Used to enable or disable encryption of the wireless radio
signals if the installed PC Card supports encryption, and
the Access Point is in the 'trusted' security mode. After
changing this value, it will not be loaded onto the card
until reset is performed.
This value varies from wliEncSelect in that it shows the
future value of the encryption mode after the next reset,
and wliEncSelect is read-only.
If the Access Point is in the 'non-trusted' security mode,
this parameter cannot be set via SNMP, only through the
console port.
Parsed from file RoamAbout-MIB.mib
Module: RoamAbout-MIB
Vendor: DEC
Module: RoamAbout-MIB
[Automatically extracted from oidview.com]
rabtEncryptionEnable OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Used to enable or disable encryption of the wireless radio signals if the installed PC Card supports encryption, and the Access Point is in the 'trusted' security mode. After changing this value, it will not be loaded onto the card until reset is performed. This value varies from wliEncSelect in that it shows the future value of the encryption mode after the next reset, and wliEncSelect is read-only. If the Access Point is in the 'non-trusted' security mode, this parameter cannot be set via SNMP, only through the console port." ::= { roamabout 13 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.36.2.18.35.1 | rabtPCCardType | 0 | 0 | The type of PC card inserted in the Access Point. |
| 1.3.6.1.4.1.36.2.18.35.2 | rabtIPAddressState | 0 | 0 | Determines the state of IP Address storage. A value of 2 causes the current IP address to be stored in NVRAM. |
| 1.3.6.1.4.1.36.2.18.35.3 | rabtBridgeMode | 0 | 0 | CURRENT Access Point bridge mode state. LAN-to-LAN mode is the improved name for 802.11. LAN-to-LAN used to be called full-brid… |
| 1.3.6.1.4.1.36.2.18.35.4 | rabtUplineDumpMode | 0 | 0 | Determines whether or not a dump file is created on an Access Point crash. |
| 1.3.6.1.4.1.36.2.18.35.5 | rabtMemorySize | 0 | 0 | The size of the memory in the Access Point in Mbytes. |
| 1.3.6.1.4.1.36.2.18.35.6 | rabtUpgradeFlash | 0 | 0 | Causes the Access Point to attempt a flash upgrade. Be aware that this causes the Access Point to reset. |
| 1.3.6.1.4.1.36.2.18.35.7 | rabtForceUplineDump | 0 | 0 | Causes the Access Point to attempt a upline dump. Be aware that this causes the Access Point to reset. |
| 1.3.6.1.4.1.36.2.18.35.8 | rabtStationName | 0 | 0 | The wireless station name sent out as part of the beacon messages. Valid only when a DS card is inserted in the Access Point. |
| 1.3.6.1.4.1.36.2.18.35.9 | rabtIPSubnetMask | 0 | 0 | The IP subnet mask for this access Point. |
| 1.3.6.1.4.1.36.2.18.35.10 | rabtDSChannel | 0 | 0 | The channel number for the wireless non-IEEE 2400DS card. This value is only valid currently if a 2400DS card is installed. Afte… |
| 1.3.6.1.4.1.36.2.18.35.11 | rabtDSCountryVariant | 0 | 0 | Describes the country variant of the 2400DS card. This value is only valid currently if a 2400DS card is installed. |
| 1.3.6.1.4.1.36.2.18.35.12 | rabtDSCurrentNWID | 0 | 0 | The WaveLAN Network ID (NWID) this RF-modem is currently operating with. |
| 1.3.6.1.4.1.36.2.18.35.14 | rabtPTPDiag | 9 | 9 | None |
| 1.3.6.1.4.1.36.2.18.35.15 | rabtDot11 | 5 | 56 | None |
| 1.3.6.1.4.1.36.2.18.35.16 | roamaboutLoader | 7 | 7 | None |
| 1.3.6.1.4.1.36.2.18.35.17 | roamaboutConsole | 1 | 1 | None |