When this mode is set to enabled, the AP will only associate
with stations that have the same network name as the AP.
When this mode is set to disabled, a station with the
network name of ANY is allowed to associate.
The term future means that a change takes effect after the
next reset of the Access Point. The current multicast PM
buffering state is read from
rabtDot11CurrentMulticastPMBuffering.
Parsed from file RoamAbout-MIB.mib
Module: RoamAbout-MIB
Vendor: DEC
Module: RoamAbout-MIB
[Automatically extracted from oidview.com]
rabtDot11FutureSecureAccess OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "When this mode is set to enabled, the AP will only associate with stations that have the same network name as the AP. When this mode is set to disabled, a station with the network name of ANY is allowed to associate. The term future means that a change takes effect after the next reset of the Access Point. The current multicast PM buffering state is read from rabtDot11CurrentMulticastPMBuffering." ::= { rabtDot11Future 10 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.36.2.18.35.15.2.1 | rabtDot11FutureChannel | 0 | 0 | Defines the FUTURE channel (communication frequency) to be used for creating a BSS. Note that different subsets of channels are … |
| 1.3.6.1.4.1.36.2.18.35.15.2.2 | rabtDot11FutureNetworkName | 0 | 0 | Defines the FUTURE Service Set IDentifier to be used for the BSS. The term future means that a change takes effect after the next… |
| 1.3.6.1.4.1.36.2.18.35.15.2.3 | rabtDot11FutureStationName | 0 | 0 | Defines the FUTURE station name of the radio interface, used by client utilities. The term future means that a change takes effec… |
| 1.3.6.1.4.1.36.2.18.35.15.2.4 | rabtDot11FutureOperationalRate | 0 | 0 | This attribute shall specify the set of data rates at which the station may transmit data. Each octet contains a value represent… |
| 1.3.6.1.4.1.36.2.18.35.15.2.5 | rabtDot11FutureSystemScale | 0 | 0 | Specifies the FUTURE Access Point density in the ESS. The term future means that the change takes effect after the next reset of … |
| 1.3.6.1.4.1.36.2.18.35.15.2.6 | rabtDot11FutureDTIMPeriod | 0 | 0 | Defines the FUTURE number of beacon intervals between successive DTIMs. The term future means that a change takes effect after t… |
| 1.3.6.1.4.1.36.2.18.35.15.2.7 | rabtDot11FutureFragmentationThreshold | 0 | 0 | This attribute shall specify the mandatory maximum size, in octets, of the MPDU that may be delivered to the PHY. An MSDU shall b… |
| 1.3.6.1.4.1.36.2.18.35.15.2.8 | rabtDot11FutureRTSThreshold | 0 | 0 | This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed. An RTS/CT… |
| 1.3.6.1.4.1.36.2.18.35.15.2.9 | rabtDot11FutureMulticastPMBuffering | 0 | 0 | Defines if multicast MAC frames are to be buffered for transmission after DTIM in the FUTURE. If disabled, MAC frames will be im… |
| 1.3.6.1.4.1.36.2.18.35.15.2.11 | rabtDot11FutureTransmitRate | 0 | 0 | This value specifies the transmission rate of the AP. It is implemented when cards that operate faster than the 2Mbit 802.11 stan… |
| 1.3.6.1.4.1.36.2.18.35.15.2.12 | rabtDot11FuturePrivacyInvoked | 0 | 0 | This value specifies the future setting of the dot11PrivacyInvoked attribute in the AP. |
| 1.3.6.1.4.1.36.2.18.35.15.2.13 | rabtDot11FutureExcludeUnencrypted | 0 | 0 | This value specifies the future value of the dot11ExcludeUnencrypted attribute in the AP. |