This parameter is used to specify how the entries
in this table are used.
If this object is set to primary(1), the system
will use only the primary boot source when
rebooting. (note, this is the entry where
a3sysUblSource = primary(1)).
If this object is set to primaryAndSecondary(2),
the system will attempt to boot first from the
primary boot source, and, if that fails (after
a3sysUblMaxRetries attemps), the system will
try the secondary boot source.
If this object has the value testWithPrimaryBackup(3),
the system, when rebooting, will perform a test boot
using the 'test' boot source. Note, the NetBuilder
Remote Office uses entry 3 in a3sysUserBootListTable
as the 'test' boot source (a3sysUblSource = test(3)),
while other 3Com routers (NetBuilder II, NetBuilder Remote,
NetBuilder Remote Control, NetBuilder Local, and NetBuilder
Remote Access) don't support all 4 rows in a3sysUserBootListTable,
and simply use the secondary boot source (a3sysUblSource = secondary(2))
to identify the 'test' boot source.
After booting from the 'test' boot source, if the
Test Recovery Timer (a3sysTestRecoveryTimer) is
allowed to count down to zero, the system will
reboot using the primary boot source. (see the
reference guide for details about test booting).
When in this mode, to prevent the system from rebooting
using the primary boot source, the Test Recovery Timer
(a3sysTestRecoveryTimer) must be set to zero.
Note, this object cannot be set to testWithPrimaryBackup(3)
explicitly. Instead, by setting a3sysTestBootTimer to a
non-zero value, the system will automatically go into
'Test Boot' mode and this object will be given the
value testWithPrimaryBackup(3).
If this object has the value secondary(4), the system will
use only the secondary boot source when rebooting.
Parsed from file a3Com-sys.mib.txt
Company: None
Module: A3Com-System-r4-MIB
This parameter is used to specify how the entries
in this table are used.
If this object is set to primary(1), the system
will use only the primary boot source when
rebooting. (note, this is the entry where
a3sysUblSource = primary(1)).
If this object is set to primaryAndSecondary(2),
the system will attempt to boot first from the
primary boot source, and, if that fails (after
a3sysUblMaxRetries attemps), the system will
try the secondary boot source.
If this object has the value testWithPrimaryBackup(3),
the system, when rebooting, will perform a test boot
using the 'test' boot source. Note, the NetBuilder Remote
Office and NetBuilder II use entry 3 in a3sysUserBootListTable
as the 'test' boot source (a3sysUblSource = test(3)),
while other 3Com routers (NetBuilder Remote, NetBuilder
Remote Control, NetBuilder Local, and NetBuilder Remote
Access) don't support all 4 rows in a3sysUserBootListTable,
and simply use the secondary boot source (a3sysUblSource = secondary(2))
to identify the 'test' boot source.
After booting from the 'test' boot source, if the
Test Recovery Timer (a3sysTestRecoveryTimer) is
allowed to count down to zero, the system will
reboot using the primary boot source. (see the
reference guide for details about test booting).
When in this mode, to prevent the system from rebooting
using the primary boot source, the Test Recovery Timer
(a3sysTestRecoveryTimer) must be set to zero.
Note, this object cannot be set to testWithPrimaryBackup(3)
explicitly. Instead, by setting a3sysTestBootTimer to a
non-zero value, the system will automatically go into
'Test Boot' mode and this object will be given the
value testWithPrimaryBackup(3).
If this object has the value secondary(4), the system will
use only the secondary boot source when rebooting.
Parsed from file A3Com-System-r8-MIB.mib
Module: A3Com-System-r8-MIB
Child arc 0 is used to translate between SNMPv1 and SNMPv2 notification parameters as explained in IETF RFC 2576, section 3.
a3sysBootSources OBJECT-TYPE SYNTAX INTEGER { primary (1), primaryAndSecondary (2), testWithPrimaryBackup (3), secondary (4) } ACCESS read-write STATUS mandatory DESCRIPTION "This parameter is used to specify how the entries in this table are used. If this object is set to primary(1), the system will use only the primary boot source when rebooting. (note, this is the entry where a3sysUblSource = primary(1)). If this object is set to primaryAndSecondary(2), the system will attempt to boot first from the primary boot source, and, if that fails (after a3sysUblMaxRetries attemps), the system will try the secondary boot source. If this object has the value testWithPrimaryBackup(3), the system, when rebooting, will perform a test boot using the 'test' boot source. Note, the NetBuilder Remote Office uses entry 3 in a3sysUserBootListTable as the 'test' boot source (a3sysUblSource = test(3)), while other 3Com routers (NetBuilder II, NetBuilder Remote, NetBuilder Remote Control, NetBuilder Local, and NetBuilder Remote Access) don't support all 4 rows in a3sysUserBootListTable, and simply use the secondary boot source (a3sysUblSource = secondary(2)) to identify the 'test' boot source. After booting from the 'test' boot source, if the Test Recovery Timer (a3sysTestRecoveryTimer) is allowed to count down to zero, the system will reboot using the primary boot source. (see the reference guide for details about test booting). When in this mode, to prevent the system from rebooting using the primary boot source, the Test Recovery Timer (a3sysTestRecoveryTimer) must be set to zero. Note, this object cannot be set to testWithPrimaryBackup(3) explicitly. Instead, by setting a3sysTestBootTimer to a non-zero value, the system will automatically go into 'Test Boot' mode and this object will be given the value testWithPrimaryBackup(3). If this object has the value secondary(4), the system will use only the secondary boot source when rebooting." ::= { a3ComBoot 8 }
a3sysBootSources OBJECT-TYPE SYNTAX INTEGER { primary (1), primaryAndSecondary (2), testWithPrimaryBackup (3), secondary (4) } ACCESS read-write STATUS mandatory DESCRIPTION "This parameter is used to specify how the entries in this table are used. If this object is set to primary(1), the system will use only the primary boot source when rebooting. (note, this is the entry where a3sysUblSource = primary(1)). If this object is set to primaryAndSecondary(2), the system will attempt to boot first from the primary boot source, and, if that fails (after a3sysUblMaxRetries attemps), the system will try the secondary boot source. If this object has the value testWithPrimaryBackup(3), the system, when rebooting, will perform a test boot using the 'test' boot source. Note, the NetBuilder Remote Office and NetBuilder II use entry 3 in a3sysUserBootListTable as the 'test' boot source (a3sysUblSource = test(3)), while other 3Com routers (NetBuilder Remote, NetBuilder Remote Control, NetBuilder Local, and NetBuilder Remote Access) don't support all 4 rows in a3sysUserBootListTable, and simply use the secondary boot source (a3sysUblSource = secondary(2)) to identify the 'test' boot source. After booting from the 'test' boot source, if the Test Recovery Timer (a3sysTestRecoveryTimer) is allowed to count down to zero, the system will reboot using the primary boot source. (see the reference guide for details about test booting). When in this mode, to prevent the system from rebooting using the primary boot source, the Test Recovery Timer (a3sysTestRecoveryTimer) must be set to zero. Note, this object cannot be set to testWithPrimaryBackup(3) explicitly. Instead, by setting a3sysTestBootTimer to a non-zero value, the system will automatically go into 'Test Boot' mode and this object will be given the value testWithPrimaryBackup(3). If this object has the value secondary(4), the system will use only the secondary boot source when rebooting." ::= { a3ComBoot 8 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.43.2.13.10.8.0 | a3sysBootSources | 0 | 0 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.43.2.13.10.1 | a3sysReBoot | 1 | 1 | This object can be used to reboot the system. If this object is set to stdReboot(2), the system's action is determined by the val… |
| 1.3.6.1.4.1.43.2.13.10.2 | a3sysTestBootTime | 1 | 1 | The Test Boot Time indicates the number of seconds after a test reboot the system will automatically reboot. Upon reboot, the sy… |
| 1.3.6.1.4.1.43.2.13.10.3 | a3sysStartUpAction | 1 | 1 | This parameter determines the boot source when the system is powered on or reset. If monitor (1) is chosen, the system enters mon… |
| 1.3.6.1.4.1.43.2.13.10.4 | a3sysTestRecoveryTimer | 1 | 1 | This object contains the real time value of the Test Recovery Timer. When the system is performing a 'test boot' (ie, a boot whe… |
| 1.3.6.1.4.1.43.2.13.10.5 | a3sysDirectedReBoots | 1 | 1 | This is a counter that tracks the number of times the system has completed successfully a boot, no matter how the boot was initia… |
| 1.3.6.1.4.1.43.2.13.10.6 | a3sysExceptionReBoots | 1 | 1 | This is a counter that tracks the number of times the system has crashed and a reboot sequence is begun by the exception handler.… |
| 1.3.6.1.4.1.43.2.13.10.7 | a3sysBootDump | 1 | 1 | This determines whether or not a memory dump is performed if the system fails due to a software problem. If noDump (1) is select… |
| 1.3.6.1.4.1.43.2.13.10.9 | a3sysUserBootListTable | 1 | 28 | This table defines a list of boot sources (and for the NetBuilder Remote Office There are two other parameters that dictate how t… |
| 1.3.6.1.4.1.43.2.13.10.10 | a3sysIioBootTable | 1 | 6 | This table specifies where each IIO card obtains its boot image. |