sysConfig OBJECT IDENTIFIER ::= { series2000 2 }
Vendor: Grand Junction Networks
Module: STAND-ALONE-ETHERNET-SWITCH-MIB
[Automatically extracted from oidview.com]
sysConfig OBJECT IDENTIFIER ::= { series2000 2 }
sysConfig OBJECT IDENTIFIER ::= { series2000 2 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.437.1.1.3.2.1 | sysConfigReset | 1 | 1 | Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self T… |
| 1.3.6.1.4.1.437.1.1.3.2.2 | sysConfigDefaultReset | 1 | 1 | Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self T… |
| 1.3.6.1.4.1.437.1.1.3.2.3 | sysConfigClearPortStats | 1 | 1 | Setting this object to noClear(1) results in no action. When set to clear(2), the switch will reset all port statistics to zero. … |
| 1.3.6.1.4.1.437.1.1.3.2.4 | sysConfigAddressViolationAction | 1 | 1 | Indicates what action to take when an address violation (an address mismatch or duplication) occurs on a secured port. The defau… |
| 1.3.6.1.4.1.437.1.1.3.2.5 | sysConfigAddressViolationAlert | 1 | 1 | When set to enabled(1), the switch will generate an addressViolation trap upon detecting an address violation on a secured port. … |
| 1.3.6.1.4.1.437.1.1.3.2.6 | sysConfigSwitchingMode | 1 | 1 | The switch can operate as a high speed cut-through switch, or as a traditional store-and-forward switch. Cut-through switching of… |
| 1.3.6.1.4.1.437.1.1.3.2.7 | sysConfigMulticastStoreAndForward | 1 | 1 | When set to enabled(1), the switching of multicast frames will use the store-and-forward method, regardless of the setting of sys… |
| 1.3.6.1.4.1.437.1.1.3.2.8 | sysConfigMonitor | 1 | 1 | Selects whether frames to/from certain ports are sent to sysConfigMonitorPort. A port is selected for monitoring purpose when it… |
| 1.3.6.1.4.1.437.1.1.3.2.9 | sysConfigMonitorPort | 1 | 1 | Port number to which all frames to/from monitored ports are sent. Frames are only monitored if the sysConfigMonitor object is se… |
| 1.3.6.1.4.1.437.1.1.3.2.10 | sysConfigHigherProtocolMonitor | 1 | 1 | Selects whether frames addressed to and from the higher- layer protocol processor of the switch are to be monitored. The higher-… |
| 1.3.6.1.4.1.437.1.1.3.2.11 | sysConfigPort25Connector | 1 | 1 | Specify which of the two connector types is providing active connection on port 25. Setting the connector to self-sensing allows… |
| 1.3.6.1.4.1.437.1.1.3.2.12 | sysConfigHeuristics | 1 | 1 | A value which enables special heuristic functions. The value is a sum. This sum initially takes the value zero, Then, for each h… |
| 1.3.6.1.4.1.437.1.1.3.2.13 | sysConfigEnableSTP | 1 | 1 | The switch implements the 802.1d Spanning Tree Algorithm & Protocol (STP) on all its port to detect loops in the bridge topology.… |
| 1.3.6.1.4.1.437.1.1.3.2.14 | sysConfigStrictSTPTransition | 1 | 1 | The 802.1d Spanning Tree Protocol dictates that a port must start out in the blocking state and transition through two other inte… |
| 1.3.6.1.4.1.437.1.1.3.2.15 | sysConfigBroadcastStormAction | 1 | 1 | Indicates what action to take when broadcast threshold is exceeded at a port. block : broadcast packets received from the port a… |
| 1.3.6.1.4.1.437.1.1.3.2.16 | sysConfigBroadcastStormAlert | 1 | 1 | When set to enabled(1), the switch will generate a broadcastStormTrap upon detecting that a port is receiving broadcast packets a… |
| 1.3.6.1.4.1.437.1.1.3.2.17 | sysConfigBroadcastThreshold | 1 | 1 | This object allows user to set the upper limit for Broadcast storm control function. The broadcast rate is the number of broadcas… |
| 1.3.6.1.4.1.437.1.1.3.2.18 | sysConfigBroadcastReEnableThreshold | 1 | 1 | This object allows user to set the re-enable threshold for Broadcast Storm Control function. Once a port has been blocked, the nu… |
| 1.3.6.1.4.1.437.1.1.3.2.19 | sysConfig10MbpsEnhancedCongestionControl, sysConfig10MbpsACR | 1 | 1 | Acceleration Congestion Resolution (ACR) reduces the transmit back-off period to allow a port to transmit packets more quickly, Th… |
| 1.3.6.1.4.1.437.1.1.3.2.20 | sysConfigNetworkPort | 1 | 1 | If a network port is configured, all unknown unicast packets are sent only to the network port. Only one port in the switch can b… |
| 1.3.6.1.4.1.437.1.1.3.2.21 | sysConfigHalfDuplexBackPressure | 1 | 1 | Back-pressure allows a port to force a collision when there are no buffers to receive frames. Because collision is only meaningf… |
| 1.3.6.1.4.1.437.1.1.3.2.22 | sysConfigFastEthcParmsPort | 1 | 1 | The parameters of port to use for Fast EtherChannel. Defaults to 26. When Fast EtherChannel is enabled, the following object valu… |
| 1.3.6.1.4.1.437.1.1.3.2.23 | sysConfigTftpServerName | 1 | 1 | The TFTP server host name or IP address. The value of this object is the same as upgradeTFTPServerName object. |
| 1.3.6.1.4.1.437.1.1.3.2.24 | sysConfigConfigFileAuto | 1 | 1 | Selects whether the system should attempt to retrieve the configuration file on system power-up. When enabled, the system will at… |
| 1.3.6.1.4.1.437.1.1.3.2.25 | sysConfigPortGroupingMode | 1 | 1 | When set to bridge-groups (1), the switch allows ports to be assigned to bridge groups. Bridge Group configuration is local to th… |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.437.1.1.3.0 | logonIntruder | 0 | 0 | None |
| 1.3.6.1.4.1.437.1.1.3.1 | switchDiagnostic, sysInfo | 21 | 42 | None |
| 1.3.6.1.4.1.437.1.1.3.3 | port | 4 | 92 | None |
| 1.3.6.1.4.1.437.1.1.3.4 | broadcastStorm, netMgmt | 25 | 59 | None |
| 1.3.6.1.4.1.437.1.1.3.5 | rpsFailed, upgrade | 10 | 20 | None |
| 1.3.6.1.4.1.437.1.1.3.6 | ipAddressChange, vlan | 6 | 27 | None |
| 1.3.6.1.4.1.437.1.1.3.7 | bandwidthUsage | 6 | 16 | None |
| 1.3.6.1.4.1.437.1.1.3.8 | bridgeGroup, supervisorLog | 4 | 14 | None |