Enhanced Congestion Control (ECC) reduces the transmit
back-off period to allow the port to transmit more quickly,
thereby reducing the transmit queue congestion
on the port. When set to disabled(2), ECC is disabled.
When set to adaptive(1), ECC is enabled when the ports
transmit queue is full. Set to moderate-aggressive(3)
to enable ECC with a back-off period that is divided by
a factor of 32. Set to aggressive(4) to enable ECC with
a back-off period that is divided by a factor of 1024.
This object controls the setting on all 10Mbps ports of
the switch.
The default value is disabled(1).
Acceleration Congestion Resolution (ACR)
reduces the transmit back-off period to
allow a port to transmit packets more quickly,
This object configures ACR for all 10 Mbps ports.
The options are as follows:
disabled: ACR is disabled.
adaptive: ACR is enabled when transmit queue is full.
moderate-aggressive: ACR is enabled with a backoff
period that is divided by a factor of ??.
aggressive: ACR is enabled with a backoff period that is
divided by a factor of ??.
The default value is disabled(1).
Parsed from file ESSWITCH-MIB.my.txt
Company: None
Module: STAND-ALONE-ETHERNET-SWITCH-MIB
Enhanced Congestion Control (ECC) reduces the transmit
back-off period to allow the port to transmit more quickly,
thereby reducing the transmit queue congestion
on the port. When set to disabled(2), ECC is disabled.
When set to adaptive(1), ECC is enabled when the ports
transmit queue is full. Set to moderate-aggressive(3)
to enable ECC with a back-off period that is divided by
a factor of 32. Set to aggressive(4) to enable ECC with
a back-off period that is divided by a factor of 1024.
This object controls the setting on all 10Mbps ports of
the switch.
The default value is disabled(1).
Parsed from file STAND-ALONE-ETHERNET-SWITCH-MIB.mib
Module: STAND-ALONE-ETHERNET-SWITCH-MIB
sysConfig10MbpsEnhancedCongestionControl OBJECT-TYPE SYNTAX INTEGER { adaptive(1), disabled(2), moderate-aggressive(3), aggressive(4)} ACCESS read-write STATUS mandatory DESCRIPTION "Enhanced Congestion Control (ECC) reduces the transmit back-off period to allow the port to transmit more quickly, thereby reducing the transmit queue congestion on the port. When set to disabled(2), ECC is disabled. When set to adaptive(1), ECC is enabled when the ports transmit queue is full. Set to moderate-aggressive(3) to enable ECC with a back-off period that is divided by a factor of 32. Set to aggressive(4) to enable ECC with a back-off period that is divided by a factor of 1024. This object controls the setting on all 10Mbps ports of the switch. The default value is disabled(1)." ::= { sysConfig 19 }
Vendor: Grand Junction Networks
Module: STAND-ALONE-ETHERNET-SWITCH-MIB
[Automatically extracted from oidview.com]
sysConfig10MbpsACR OBJECT-TYPE SYNTAX INTEGER { adaptive(1), disabled(2), moderate-aggressive(3), aggressive(4)} ACCESS read-write STATUS mandatory DESCRIPTION "Acceleration Congestion Resolution (ACR) reduces the transmit back-off period to allow a port to transmit packets more quickly, This object configures ACR for all 10 Mbps ports. The options are as follows: disabled: ACR is disabled. adaptive: ACR is enabled when transmit queue is full. moderate-aggressive: ACR is enabled with a backoff period that is divided by a factor of ??. aggressive: ACR is enabled with a backoff period that is divided by a factor of ??. The default value is disabled(1)." ::= { sysConfig 19 }
sysConfig10MbpsEnhancedCongestionControl OBJECT-TYPE SYNTAX INTEGER { adaptive(1), disabled(2), moderate-aggressive(3), aggressive(4)} ACCESS read-write STATUS mandatory DESCRIPTION "Enhanced Congestion Control (ECC) reduces the transmit back-off period to allow the port to transmit more quickly, thereby reducing the transmit queue congestion on the port. When set to disabled(2), ECC is disabled. When set to adaptive(1), ECC is enabled when the ports transmit queue is full. Set to moderate-aggressive(3) to enable ECC with a back-off period that is divided by a factor of 32. Set to aggressive(4) to enable ECC with a back-off period that is divided by a factor of 1024. This object controls the setting on all 10Mbps ports of the switch. The default value is disabled(1)." ::= { sysConfig 19 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.437.1.1.3.2.19.0 | sysConfig10MbpsACR | 0 | 0 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.437.1.1.3.2.1 | sysConfigReset | 1 | 1 | Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self T… |
| 1.3.6.1.4.1.437.1.1.3.2.2 | sysConfigDefaultReset | 1 | 1 | Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self T… |
| 1.3.6.1.4.1.437.1.1.3.2.3 | sysConfigClearPortStats | 1 | 1 | Setting this object to noClear(1) results in no action. When set to clear(2), the switch will reset all port statistics to zero. … |
| 1.3.6.1.4.1.437.1.1.3.2.4 | sysConfigAddressViolationAction | 1 | 1 | Indicates what action to take when an address violation (an address mismatch or duplication) occurs on a secured port. The defau… |
| 1.3.6.1.4.1.437.1.1.3.2.5 | sysConfigAddressViolationAlert | 1 | 1 | When set to enabled(1), the switch will generate an addressViolation trap upon detecting an address violation on a secured port. … |
| 1.3.6.1.4.1.437.1.1.3.2.6 | sysConfigSwitchingMode | 1 | 1 | The switch can operate as a high speed cut-through switch, or as a traditional store-and-forward switch. Cut-through switching of… |
| 1.3.6.1.4.1.437.1.1.3.2.7 | sysConfigMulticastStoreAndForward | 1 | 1 | When set to enabled(1), the switching of multicast frames will use the store-and-forward method, regardless of the setting of sys… |
| 1.3.6.1.4.1.437.1.1.3.2.8 | sysConfigMonitor | 1 | 1 | Selects whether frames to/from certain ports are sent to sysConfigMonitorPort. A port is selected for monitoring purpose when it… |
| 1.3.6.1.4.1.437.1.1.3.2.9 | sysConfigMonitorPort | 1 | 1 | Port number to which all frames to/from monitored ports are sent. Frames are only monitored if the sysConfigMonitor object is se… |
| 1.3.6.1.4.1.437.1.1.3.2.10 | sysConfigHigherProtocolMonitor | 1 | 1 | Selects whether frames addressed to and from the higher- layer protocol processor of the switch are to be monitored. The higher-… |
| 1.3.6.1.4.1.437.1.1.3.2.11 | sysConfigPort25Connector | 1 | 1 | Specify which of the two connector types is providing active connection on port 25. Setting the connector to self-sensing allows… |
| 1.3.6.1.4.1.437.1.1.3.2.12 | sysConfigHeuristics | 1 | 1 | A value which enables special heuristic functions. The value is a sum. This sum initially takes the value zero, Then, for each h… |
| 1.3.6.1.4.1.437.1.1.3.2.13 | sysConfigEnableSTP | 1 | 1 | The switch implements the 802.1d Spanning Tree Algorithm & Protocol (STP) on all its port to detect loops in the bridge topology.… |
| 1.3.6.1.4.1.437.1.1.3.2.14 | sysConfigStrictSTPTransition | 1 | 1 | The 802.1d Spanning Tree Protocol dictates that a port must start out in the blocking state and transition through two other inte… |
| 1.3.6.1.4.1.437.1.1.3.2.15 | sysConfigBroadcastStormAction | 1 | 1 | Indicates what action to take when broadcast threshold is exceeded at a port. block : broadcast packets received from the port a… |
| 1.3.6.1.4.1.437.1.1.3.2.16 | sysConfigBroadcastStormAlert | 1 | 1 | When set to enabled(1), the switch will generate a broadcastStormTrap upon detecting that a port is receiving broadcast packets a… |
| 1.3.6.1.4.1.437.1.1.3.2.17 | sysConfigBroadcastThreshold | 1 | 1 | This object allows user to set the upper limit for Broadcast storm control function. The broadcast rate is the number of broadcas… |
| 1.3.6.1.4.1.437.1.1.3.2.18 | sysConfigBroadcastReEnableThreshold | 1 | 1 | This object allows user to set the re-enable threshold for Broadcast Storm Control function. Once a port has been blocked, the nu… |
| 1.3.6.1.4.1.437.1.1.3.2.20 | sysConfigNetworkPort | 1 | 1 | If a network port is configured, all unknown unicast packets are sent only to the network port. Only one port in the switch can b… |
| 1.3.6.1.4.1.437.1.1.3.2.21 | sysConfigHalfDuplexBackPressure | 1 | 1 | Back-pressure allows a port to force a collision when there are no buffers to receive frames. Because collision is only meaningf… |
| 1.3.6.1.4.1.437.1.1.3.2.22 | sysConfigFastEthcParmsPort | 1 | 1 | The parameters of port to use for Fast EtherChannel. Defaults to 26. When Fast EtherChannel is enabled, the following object valu… |
| 1.3.6.1.4.1.437.1.1.3.2.23 | sysConfigTftpServerName | 1 | 1 | The TFTP server host name or IP address. The value of this object is the same as upgradeTFTPServerName object. |
| 1.3.6.1.4.1.437.1.1.3.2.24 | sysConfigConfigFileAuto | 1 | 1 | Selects whether the system should attempt to retrieve the configuration file on system power-up. When enabled, the system will at… |
| 1.3.6.1.4.1.437.1.1.3.2.25 | sysConfigPortGroupingMode | 1 | 1 | When set to bridge-groups (1), the switch allows ports to be assigned to bridge groups. Bridge Group configuration is local to th… |