This object specifies a delay in seconds between every
dial-out failure. The value zero indicates an infinite
delay. Normally, the switch will attempt a dial-out
if the netMgmtModemDialString object is non-empty. If the
remote site then fails to answer, and auto-answer has
been disabled on this system, the system will retry the
dial-out attempt after this delay has passed.
If auto-answer is enabled and the first dial-out attempt
fails, the system will stop further dial-out attempts and
immediately go into auto-answer mode. The default value
is 300 seconds, or 5 minutes.
This object specifies a delay in seconds between every
dial-out failure. The value zero indicates an infinite
delay. Normally, the switch will attempt a dial-out
if the netMgmtModemDialString object is non-empty. If the
remote site then fails to answer, and auto-answer has
been disabled on this system, the system will retry the
dial-out attempt after this delay has passed.
If auto-answer is enabled and the first dial-out attempt
fails, the system will stop further dial-out attempts and
immediately go into auto-answer mode. The default value
is 300 seconds, or 5 minutes.
Parsed from file ESSWITCH-MIB.my.txt
Company: None
Module: STAND-ALONE-ETHERNET-SWITCH-MIB
This object specifies a delay in seconds between every
dial-out failure. The value zero indicates an infinite
delay. Normally, the switch will attempt a dial-out
if the netMgmtModemDialString object is non-empty. If the
remote site then fails to answer, and auto-answer has
been disabled on this system, the system will retry the
dial-out attempt after this delay has passed.
If auto-answer is enabled and the first dial-out attempt
fails, the system will stop further dial-out attempts and
immediately go into auto-answer mode. The default value
is 300 seconds, or 5 minutes.
Parsed from file STAND-ALONE-ETHERNET-SWITCH-MIB.mib
Module: STAND-ALONE-ETHERNET-SWITCH-MIB
netMgmtModemDialDelay OBJECT-TYPE SYNTAX INTEGER (0..65500) ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies a delay in seconds between every dial-out failure. The value zero indicates an infinite delay. Normally, the switch will attempt a dial-out if the netMgmtModemDialString object is non-empty. If the remote site then fails to answer, and auto-answer has been disabled on this system, the system will retry the dial-out attempt after this delay has passed. If auto-answer is enabled and the first dial-out attempt fails, the system will stop further dial-out attempts and immediately go into auto-answer mode. The default value is 300 seconds, or 5 minutes." ::= { netMgmt 11 }
Vendor: Grand Junction Networks
Module: STAND-ALONE-ETHERNET-SWITCH-MIB
[Automatically extracted from oidview.com]
netMgmtModemDialDelay OBJECT-TYPE SYNTAX INTEGER (0..65500) ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies a delay in seconds between every dial-out failure. The value zero indicates an infinite delay. Normally, the switch will attempt a dial-out if the netMgmtModemDialString object is non-empty. If the remote site then fails to answer, and auto-answer has been disabled on this system, the system will retry the dial-out attempt after this delay has passed. If auto-answer is enabled and the first dial-out attempt fails, the system will stop further dial-out attempts and immediately go into auto-answer mode. The default value is 300 seconds, or 5 minutes." ::= { netMgmt 11 }
netMgmtModemDialDelay OBJECT-TYPE SYNTAX INTEGER (0..65500) ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies a delay in seconds between every dial-out failure. The value zero indicates an infinite delay. Normally, the switch will attempt a dial-out if the netMgmtModemDialString object is non-empty. If the remote site then fails to answer, and auto-answer has been disabled on this system, the system will retry the dial-out attempt after this delay has passed. If auto-answer is enabled and the first dial-out attempt fails, the system will stop further dial-out attempts and immediately go into auto-answer mode. The default value is 300 seconds, or 5 minutes." ::= { netMgmt 11 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.437.1.1.3.4.11.0 | netMgmtModemDialDelay | 0 | 0 | None |
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.437.1.1.3.4.1 | netMgmtIpAddress | 1 | 1 | The switch's administrative IP address. The switch may automatically discover a value for this object using the BootStrap protoc… |
1.3.6.1.4.1.437.1.1.3.4.2 | netMgmtIpSubnetMask | 1 | 1 | The switch's administrative IP subnet mask. The switch may automatically discover a value for this object using the BootStrap pr… |
1.3.6.1.4.1.437.1.1.3.4.3 | netMgmtDefaultGateway | 1 | 1 | The default gateway IP address is the address of the next hop router the switch uses to reach a non-local IP host when the switch… |
1.3.6.1.4.1.437.1.1.3.4.4 | netMgmtEnableAuthenTraps | 1 | 1 | Indicates whether the switch is permitted to generate authenticationFailure traps. The value of this object overrides any configur… |
1.3.6.1.4.1.437.1.1.3.4.5 | netMgmtEnableLinkTraps | 1 | 1 | Indicates whether the switch is permitted to generate linkUp/linkDown traps. The value of this object overrides any configuration… |
1.3.6.1.4.1.437.1.1.3.4.6 | netMgmtConsoleInactTime | 1 | 1 | The number of seconds of Management Console session inactivity to wait before ending the session. Once a session has ended, the … |
1.3.6.1.4.1.437.1.1.3.4.7 | netMgmtConsolePasswordThresh | 1 | 1 | The number of consecutive invalid password attempts allowed before the Management Console is shut down (kept silent) for a config… |
1.3.6.1.4.1.437.1.1.3.4.8 | netMgmtConsoleSilentTime | 1 | 1 | The number of minutes during which the Management Console will be unavailable after repeated failed attempts to logon. A zero va… |
1.3.6.1.4.1.437.1.1.3.4.9 | netMgmtModemInitString | 1 | 1 | This is the initialization string used to configure an attached modem. Specify this string if the modem is not Hayes compatible.… |
1.3.6.1.4.1.437.1.1.3.4.10 | netMgmtModemDialString | 1 | 1 | This string contains a phone number which is used to establish a modem connection with a remote site. Only the phone number need… |
1.3.6.1.4.1.437.1.1.3.4.12 | netMgmtModemAutoAnswer | 1 | 1 | This object specifies whether the system should be in auto-answer mode and only accepts incoming calls. Note that the system wil… |
1.3.6.1.4.1.437.1.1.3.4.13 | netMgmtSetClientTable | 1 | 5 | Table (4 entries) containing a list of IP addresses or DNS name of workstations permitted to issue SET requests. Such a workstat… |
1.3.6.1.4.1.437.1.1.3.4.14 | netMgmtTrapClientTable | 1 | 6 | Table (4 entries) containing a list of Network Management Stations that are to receive traps generated by this Network Management… |
1.3.6.1.4.1.437.1.1.3.4.15 | netMgmtCdpHoldTime | 1 | 1 | The hold time is the amount of time that a neighboring device keeps the CDP neighbor information received from this switch. If th… |
1.3.6.1.4.1.437.1.1.3.4.16 | netMgmtCdpTransmissionTime | 1 | 1 | The transmission time specifies the interval that the switch will trasnmit CDP messages from its ports. The default value is 60 s… |
1.3.6.1.4.1.437.1.1.3.4.17 | netMgmtCgmpEnable | 1 | 1 | This variable allows user to enable or disable Cisco Group Management Protocol (CGMP). Enabling CGMP will result in the deletion … |
1.3.6.1.4.1.437.1.1.3.4.18 | netMgmtCgmpRouterHoldTime | 1 | 1 | Multicast routers that support CGMP will send CGMP join message to advertise themselves to switches within a network. A switch th… |
1.3.6.1.4.1.437.1.1.3.4.19 | netMgmtVlan | 1 | 1 | The current VLAN for network management. This defaults to 1. |
1.3.6.1.4.1.437.1.1.3.4.20 | netMgmtEnableRIP | 1 | 1 | This object enables and disables Routing Information Protocol (RIP) listener to automatically discover IP gateways. The default v… |
1.3.6.1.4.1.437.1.1.3.4.21 | netMgmtDomainServer1IpAddress | 1 | 1 | The IP address of a Domain Name Server (DNS) which the system uses to resolve domain names to IP addresses. A set on this object … |
1.3.6.1.4.1.437.1.1.3.4.22 | netMgmtDomainServer2IpAddress | 1 | 1 | The IP address of a second Domain Name Server (DNS) which the system uses to resolve domain names to IP addresses. A set on this … |
1.3.6.1.4.1.437.1.1.3.4.23 | netMgmtDefaultSearchDomain | 1 | 1 | A string of up to 63 characters specifying a default domain search path. When switch needs to resolve a domain name that is not f… |
1.3.6.1.4.1.437.1.1.3.4.24 | netMgmtHttpServerAdminState | 1 | 1 | This variable enables or disables the HTTP server interface. The default value is enabled(1). |
1.3.6.1.4.1.437.1.1.3.4.25 | netMgmtHttpPort | 1 | 1 | This variable allows the user to configure a specific port on which the HTTP server will listen for TCP connections. By default, … |