A compressor has exceeded the maximum number of starts in a
minimum time period.
Parsed from file LIEBERT_GP_COND.MIB.txt
Company: None
Module: LIEBERT-GP-CONDITIONS-MIB
A compressor has exceeded the maximum number of starts in a
minimum time period.
Parsed from file LIEBERT-GP-CONDITIONS-MIB.mib
Module: LIEBERT-GP-CONDITIONS-MIB
Vendor: Emerson Computer PowerRoger Draper
Module: LIEBERT-GP-CONDITIONS-MIB
[Automatically extracted from oidview.com]
lgpConditionCompressorShortCycle OBJECT-IDENTITY STATUS current DESCRIPTION "A compressor has exceeded the maximum number of starts in a minimum time period." ::= { lgpConditionsWellKnown 9 }
lgpConditionCompressorShortCycle OBJECT-IDENTITY STATUS current DESCRIPTION "A compressor has exceeded the maximum number of starts in a minimum time period." ::= { lgpConditionsWellKnown 9 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.476.1.42.3.2.1.9.1 | lgpConditionCompressor1ShortCycle | 0 | 0 | The system has detected a short cycle event on compressor 1. The compressor has exceeded the maximum number of starts for specifi… |
| 1.3.6.1.4.1.476.1.42.3.2.1.9.2 | lgpConditionCompressor2ShortCycle | 0 | 0 | The system has detected a short cycle event on compressor 2. The compressor has exceeded the maximum number of starts for specifi… |
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.476.1.42.3.2.1.1 | lgpConditionHighTemperature | 0 | 0 | lgpConditionHightemperature |
| 1.3.6.1.4.1.476.1.42.3.2.1.2 | lgpConditionLowTemperature | 0 | 0 | The temperature is below the low temperature threshold. |
| 1.3.6.1.4.1.476.1.42.3.2.1.3 | lgpConditionHighHumidity | 0 | 0 | The humidity has exceeded the high humidity threshold. |
| 1.3.6.1.4.1.476.1.42.3.2.1.4 | lgpConditionLowHumidity | 0 | 0 | The humidity is below the low humidity threshold. |
| 1.3.6.1.4.1.476.1.42.3.2.1.5 | lgpConditionLossOfAirflow | 3 | 3 | The system has detected a loss of air flow. |
| 1.3.6.1.4.1.476.1.42.3.2.1.6 | lgpConditionChangeFilter | 0 | 0 | The system has detected a condition indicating the air filter should be changed. |
| 1.3.6.1.4.1.476.1.42.3.2.1.7 | lgpConditionCompressorHighHeadPressure | 4 | 4 | This system has detected an excessive head pressure condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.8 | lgpConditionCompressorOverload | 2 | 2 | This system has detected a compressor overload condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.10 | lgpConditionCompressorLowSuctionPressure | 0 | 0 | The pressure at a compressor inlet has dropped below the minimum setting. |
| 1.3.6.1.4.1.476.1.42.3.2.1.11 | lgpConditionMainFanOverLoad | 0 | 0 | The system has detected a main fan overload condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.12 | lgpConditionManualOverride | 0 | 0 | The system has detected a manual override condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.13 | lgpConditionStandbyGlycoolPumpOn | 0 | 0 | The standby Glycol or Glycool pump is activated. |
| 1.3.6.1.4.1.476.1.42.3.2.1.14 | lgpConditionWaterUnderFloor | 0 | 0 | Moisture has been detected under the floor. |
| 1.3.6.1.4.1.476.1.42.3.2.1.15 | lgpConditionHumidifierProblem | 0 | 0 | The system has detected a humidifier problem. |
| 1.3.6.1.4.1.476.1.42.3.2.1.16 | lgpConditionLowWaterInHumidifier | 0 | 0 | The system has detected a low water condition in the humidifier reservoir. |
| 1.3.6.1.4.1.476.1.42.3.2.1.17 | lgpConditionSmokeDetected | 0 | 0 | The system has detected smoke. |
| 1.3.6.1.4.1.476.1.42.3.2.1.18 | lgpConditionLowWaterFlow | 0 | 0 | The system has detected a low water flow rate condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.19 | lgpConditionLostPower | 0 | 0 | The system has lost power before being switched off using the controls. This condition is activated when power is restored. |
| 1.3.6.1.4.1.476.1.42.3.2.1.20 | lgpGeneralFault | 0 | 0 | A fault condition has been detected that is not identifed in the well known list. |
| 1.3.6.1.4.1.476.1.42.3.2.1.21 | lgpConditionLocalAlarm | 8 | 8 | This system has detected a local, or customer, alarm condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.22 | lgpConditionStandbyUnitOn | 0 | 0 | The system has detected the standby unit is operating. |
| 1.3.6.1.4.1.476.1.42.3.2.1.23 | lgpConditionCompressorLowPressure | 4 | 4 | This system has detected a low head compressor condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.24 | lgpConditionHighWaterInPan | 0 | 0 | The system has detected a high water condition in the condenser pan. |
| 1.3.6.1.4.1.476.1.42.3.2.1.25 | lgpConditionFaultySensor | 0 | 0 | The system has detected a faulty temperature/humidity sensor. |
| 1.3.6.1.4.1.476.1.42.3.2.1.26 | lgpConditionServiceCooling | 0 | 0 | The Cooling system requires scheduled maintenance. |
| 1.3.6.1.4.1.476.1.42.3.2.1.27 | lgpConditionServiceHumidifier | 0 | 0 | The Humidifier requires scheduled maintenance. |
| 1.3.6.1.4.1.476.1.42.3.2.1.28 | lgpConditionSystemControlBatteryLow | 0 | 0 | Charge level of the system control's battery is below the alarm set point. |
| 1.3.6.1.4.1.476.1.42.3.2.1.29 | lgpConditionGroundSystemFault | 0 | 0 | The system has detected a ground system fault. |
| 1.3.6.1.4.1.476.1.42.3.2.1.30 | lgpConditionGroundFailure | 0 | 0 | The system has detected a ground failure. |
| 1.3.6.1.4.1.476.1.42.3.2.1.31 | lgpConditionSecurityBreach | 0 | 0 | The system has detected a security breach. |
| 1.3.6.1.4.1.476.1.42.3.2.1.32 | lgpConditionEmergencyShutdown | 0 | 0 | The system has detected an emergency shutdown condition. The System is shutting down as a result of this emergency. |
| 1.3.6.1.4.1.476.1.42.3.2.1.33 | lgpConditionOnBypass | 6 | 6 | This system has detected the load is being powered by a bypass source. |
| 1.3.6.1.4.1.476.1.42.3.2.1.34 | lgpConditionOutputToLoadVoltTHD | 0 | 0 | The total harmonic distortion of the output voltage has exceeded a pre-determined threshold for a device, or system, defined amo… |
| 1.3.6.1.4.1.476.1.42.3.2.1.35 | lgpConditionLogicFailure | 0 | 0 | The system has detected a control logic failure. |
| 1.3.6.1.4.1.476.1.42.3.2.1.36 | lgpConditionPowerSupplyFault | 2 | 2 | This system had detected a power supply fault condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.37 | lgpConditionPowerSupplyFailure | 6 | 6 | This system has detected a power supply failure condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.38 | lgpConditionOverVoltage | 8 | 12 | This system has detected an over voltage condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.39 | lgpConditionUnderVoltage | 10 | 14 | This system has detected an under voltage condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.40 | lgpConditionOverload | 8 | 11 | This system has detected an overload condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.41 | lgpConditionScrShort | 4 | 4 | This system has detected a Silicon Controlled Rectifier (SCR) short condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.42 | lgpConditionScrOpen | 3 | 3 | This system has detected a Silicon Controlled Rectifier (SCR) open condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.43 | lgpConditionFanFailure | 3 | 3 | This system has detected a fan failure condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.44 | lgpConditionTransferInhibited | 0 | 0 | The system is preventing a transfer of the load to the alternate source. |
| 1.3.6.1.4.1.476.1.42.3.2.1.45 | lgpConditionAutoReTransferPrimed | 0 | 0 | The system is capable to retransfer to the preferred source. |
| 1.3.6.1.4.1.476.1.42.3.2.1.46 | lgpConditionSourcesOutOfSync | 0 | 0 | The system has detected that the input sources are not within the specified phase difference (synchronization window). |
| 1.3.6.1.4.1.476.1.42.3.2.1.47 | lgpConditionSourceFailure | 2 | 2 | This system has detected an input source failure condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.48 | lgpConditionAutoReTransferInhibited | 0 | 0 | The system is preventing a transfer of the load back to the prefered source. |
| 1.3.6.1.4.1.476.1.42.3.2.1.49 | lgpConditionAutoReTransferFailed | 0 | 0 | The system is failing to automatically retransfer the load back to the preferred source. |
| 1.3.6.1.4.1.476.1.42.3.2.1.50 | lgpConditionFuseOpen | 6 | 6 | This system has detected an open fuse condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.51 | lgpConditionDisconnect | 16 | 24 | The system has detected a disconnect condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.52 | lgpConditionFrequencyDeviation | 5 | 5 | This system has detected a frequency deviation condition. The frequency of a source is outside of the pre-determined thresholds f… |
| 1.3.6.1.4.1.476.1.42.3.2.1.53 | lgpConditionOverCurrent | 10 | 16 | This system has detected an current condition. The current of a source has risen above a pre-determined threshold for a device,… |
| 1.3.6.1.4.1.476.1.42.3.2.1.54 | lgpConditionSensorFailure | 17 | 17 | This system has detected a sensor failure condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.55 | lgpConditionInternalCommunicationFailure | 0 | 0 | This system has detected an internal communication failure condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.56 | lgpConditionExternalCommunicationFailure | 0 | 0 | This system has detected an external communication failure condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.57 | lgpConditionSourceGateDriveFailure | 2 | 2 | This system has detected a source gate drive failure condition. |
| 1.3.6.1.4.1.476.1.42.3.2.1.58 | lgpConditionDisconnectFailure | 5 | 5 | This system has detected a disconnect failure condition. A disconnect is a device which disconnects a conductor of a circuit from… |
| 1.3.6.1.4.1.476.1.42.3.2.1.59 | lgpConditionOverTemperature | 16 | 16 | This system has detected an over temperature condition. |
| ... | ||||