Allows you to control the PCL 5e print environment across print jobs.
Choices
Off: Resets PCL to its default state at the end of each
PCL print job, executes an implicit
start and end of the job, and deletes any temporary
fonts, macros, and patterns.
On: Resets PCL to its default state at the end of each
PCL print job. Temporary fonts, macros, and patterns
from previous PCL jobs are retained in memory after
the print job has completed. You can recall these
downloaded fonts, macros, or patterns from within
your PCL file without having to download them again.
On Compatibility: Retains the entire state of PCL as
well as the temporary macros, fonts,
and patterns from previous PCL jobs.
Default
Off
Notes
A retained state is cleared if you do any of the following:
* Explicitly clear the PCL state by sending an
* Turn off the printer. (Note that if Retain Temporary
is set to On or On Compatibility and power is turned
off and back on again, all temporary objects on the
disk's standard resource will become permanent.
RAM-based temporary objects are lost).
* Change any PCL front panel option.
* Send any PCL-specific DOC commands (except
the DOC emulation command).
* Send a PCL job from a different communications
port. For example, the state set up by a PCL job
using the parallel port is cleared if a subsequent
PCL job arrives at the serial port).
Parsed from file QMS-MIB.mib
Module: QMS-MIB
Vendor: QMS, Inc.
Module: QMS-MIB
[Automatically extracted from oidview.com]
qmsHPPCLPreJobReset OBJECT-TYPE SYNTAX INTEGER { off(1), on(2), oncompatibility(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Allows you to control the PCL 5e print environment across print jobs. Choices Off: Resets PCL to its default state at the end of each PCL print job, executes an implicit
E at the start and end of the job, and deletes any temporary fonts, macros, and patterns. On: Resets PCL to its default state at the end of each PCL print job. Temporary fonts, macros, and patterns from previous PCL jobs are retained in memory after the print job has completed. You can recall these downloaded fonts, macros, or patterns from within your PCL file without having to download them again. On Compatibility: Retains the entire state of PCL as well as the temporary macros, fonts, and patterns from previous PCL jobs. Default Off Notes A retained state is cleared if you do any of the following: * Explicitly clear the PCL state by sending an E or Printer Job Language. * Turn off the printer. (Note that if Retain Temporary is set to On or On Compatibility and power is turned off and back on again, all temporary objects on the disk's standard resource will become permanent. RAM-based temporary objects are lost). * Change any PCL front panel option. * Send any PCL-specific DOC commands (except the DOC emulation command). * Send a PCL job from a different communications port. For example, the state set up by a PCL job using the parallel port is cleared if a subsequent PCL job arrives at the serial port)." ::= { qmsHPPCL 10 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.480.1.525.2 | qmsHPPCLLineTermination | 0 | 0 | Indicates the default line termination mode. This setting specifies the treatment of line feeds and carriage returns. Choices CR=C… |
1.3.6.1.4.1.480.1.525.4 | qmsHPPCLFontNumber | 0 | 0 | Sets the printer's default font. Choices Courier12, Courier12bold, Courier12italic, Courier10, Courier10bold, Courier10italic, Lin… |
1.3.6.1.4.1.480.1.525.6 | qmsHPPCLLinesPerInch | 0 | 0 | Sets the default lines printed per inch in PCL jobs, regardless of page size. Choices 100 to 4800 Default 600 Notes You must enter the… |
1.3.6.1.4.1.480.1.525.8 | qmsHPPCLDefaultSymbolSet | 0 | 0 | Selects the default symbol set for the emulation. Not all symbol sets are available with certain resident fonts. In particular, … |
1.3.6.1.4.1.480.1.525.12 | qmsHPPCLPointSize | 0 | 0 | Sets the point size for scalable default fonts in units of hundreths of a point. For example, a 24 point default point size is s… |
1.3.6.1.4.1.480.1.525.16 | qmsHPPCLDefaultFontID | 0 | 0 | Sets the Default Font Index when the Default Font is set to selectbyindex. Choices 0 to 32767 Default 0 Note The index number can be o… |
1.3.6.1.4.1.480.1.525.18 | qmsHPPCLGL2Plotter | 0 | 0 | Allows your printer to emulate a monochrome or color plotter. Choices On: Sets the printer to monochrome (2 pen). Off: Sets the pr… |
1.3.6.1.4.1.480.1.525.24 | qmsHPPCLDiskOrRam | 0 | 0 | Controls the default storage location of PCL objects (fonts, macros, and patterns) when it is not otherwise specified through DO… |