An entry consisting of port information for a
particular async port.
Parsed from file SYNC-RESEARCH-MIB.mib
Module: SYNC-RESEARCH-MIB
Vendor: Sync Research, Inc.
Module: SYNC-RESEARCH-MIB
[Automatically extracted from oidview.com]
asyncConfigEntry OBJECT-TYPE SYNTAX AsyncConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry consisting of port information for a particular async port." INDEX { asyncConfigPortIndex } ::= { asyncConfigTable 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.485.3.5.6.1.1.1 | asyncConfigPortIndex | 0 | 0 | The port number that uniquely identifies this port. |
| 1.3.6.1.4.1.485.3.5.6.1.1.2 | asyncConfigType | 0 | 0 | The port type. HASC (Host Async) ports are for attaching to an Async Alarm Central Processor. TASC ports (Terminal Async) ports ar… |
| 1.3.6.1.4.1.485.3.5.6.1.1.3 | asyncNAUName | 0 | 0 | The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters). |
| 1.3.6.1.4.1.485.3.5.6.1.1.4 | asyncInitState | 0 | 0 | The initial state of the async port. If configured for 'in-service', then the Async port will be brougt up automattically when th… |
| 1.3.6.1.4.1.485.3.5.6.1.1.5 | asyncCarrier | 0 | 0 | This field indicates whether Carrier (a.k.a. CD or DCD, RS-232 pin 8) is constant or switched for DCE devices (internally clocked… |
| 1.3.6.1.4.1.485.3.5.6.1.1.6 | asyncSpeed | 0 | 0 | The ports speed in bits per second. The default value is 300 bits per second. Speeds higher than 19200 are not supported. |
| 1.3.6.1.4.1.485.3.5.6.1.1.7 | asyncPhysicalType | 0 | 0 | Physical RS-232 type emulated by the port. The default value is 2 or DCE. |
| 1.3.6.1.4.1.485.3.5.6.1.1.8 | asyncStopBits | 0 | 0 | Number of stop bits generated for transmit characters (received characters may have any number of bits regardless of the configur… |
| 1.3.6.1.4.1.485.3.5.6.1.1.9 | asyncParity | 0 | 0 | Parity type generated for transmit characters and checked for receive characters. If ODD or EVEN, then if a character is received… |
| 1.3.6.1.4.1.485.3.5.6.1.1.10 | asyncDataBits | 0 | 0 | Number of data bits (not including the parity bit). The default value is 8. |
| 1.3.6.1.4.1.485.3.5.6.1.1.11 | asyncIdleTimer | 0 | 0 | The idle timer is amount of time (in milliseconds) used to determine when a complete message has been received from the line. If… |
| 1.3.6.1.4.1.485.3.5.6.1.1.12 | asyncTxFrameGap | 0 | 0 | The TX frame gap is analogous to the idle timer, but is used to separate messages received from the network by gaps in time so th… |
| 1.3.6.1.4.1.485.3.5.6.1.1.13 | asyncRxForwardingCount | 0 | 0 | The Async receive forwarding count is used to forward messages when a configured number of characters is received from the Async … |
| 1.3.6.1.4.1.485.3.5.6.1.1.14 | asyncEiaSignalForwarding | 0 | 0 | The Async EIA signal forwarding is used to cause receive data to be forwarding based on a change of EIA RS-232 control signals. I… |
| 1.3.6.1.4.1.485.3.5.6.1.1.15 | asyncAddressOffset | 0 | 0 | If the address offset is specified as zero, then the data is not parsed to find a device address in order to direct the data to a… |
| 1.3.6.1.4.1.485.3.5.6.1.1.16 | asyncRTC | 0 | 0 | Defines whether the alarms system protocol has a record termination(forwarding character). The valid range is from hex 01 to hex … |
| 1.3.6.1.4.1.485.3.5.6.1.1.17 | asyncCTS | 0 | 0 | Defines whether CTS is an input signal used to determine the port status. This parameter is applicable if clocking is set to exte… |
| 1.3.6.1.4.1.485.3.5.6.1.1.18 | asyncDCD | 0 | 0 | Defines whether DCD is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For… |
| 1.3.6.1.4.1.485.3.5.6.1.1.19 | asyncDSR | 0 | 0 | Defines whether DSR is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For… |
| 1.3.6.1.4.1.485.3.5.6.1.1.20 | asyncDTR | 0 | 0 | Defines whether DTR is required as input signal or ignored. This parameter is applicable if the clocking is set to internal. For… |
| 1.3.6.1.4.1.485.3.5.6.1.1.21 | asyncRTS | 0 | 0 | Defines whether RTS is an input signal to determine the port status. This parameter is applicable if the clocking is set to inter… |
| 1.3.6.1.4.1.485.3.5.6.1.1.22 | asyncReturnClock | 0 | 0 | Defines whether Return Clock (SCTE) is available as input signal or ignored. This parameter is applicable if the clocking is set … |
| 1.3.6.1.4.1.485.3.5.6.1.1.23 | asyncOrt | 0 | 0 | The ORT command is a new port level command. By default, the setting will be YES to set the N2 value to zero, but can be set to … |