The interface out which a PVC-based VNIP diagnostic
will be run. This must be an interface with a valid
and stable VNIP topology for a VNIP Diagnostic.
Parsed from file TFRAP.MIB.txt
Company: None
Module: TFRAP-MIB
The interface out which a PVC-based VNIP diagnostic
will be run. This must be an interface with a valid
and stable VNIP topology for a VNIP Diagnostic.
Parsed from file TFRAP-MIB.mib
Module: TFRAP-MIB
Vendor: Sync Research, Inc.
Module: TFRAP-MIB
[Automatically extracted from oidview.com]
tfrapDiagVnipInterface OBJECT-TYPE SYNTAX INTEGER { dte-interface (1), t1-interface (2) } ACCESS read-write STATUS mandatory DESCRIPTION "The interface out which a PVC-based VNIP diagnostic will be run. This must be an interface with a valid and stable VNIP topology for a VNIP Diagnostic." ::= { tfrapDiagVnipEntry 1 }
tfrapDiagVnipInterface OBJECT-TYPE SYNTAX INTEGER { dte-interface (1), t1-interface (2) } ACCESS read-write STATUS mandatory DESCRIPTION "The interface out which a PVC-based VNIP diagnostic will be run. This must be an interface with a valid and stable VNIP topology for a VNIP Diagnostic." ::= { tfrapDiagVnipEntry 1 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.485.5.3.6.1.2 | tfrapDiagVnipIndex | 0 | 0 | The index to the external VNIP peer as presented by the VNIP topology database for the given interface. Refer to VnipTopologyTabl… |
1.3.6.1.4.1.485.5.3.6.1.3 | tfrapDiagVnipDlci | 0 | 0 | This is the DLCI value for the given interface/index combination. This comes from the VniptTopologyTable. |
1.3.6.1.4.1.485.5.3.6.1.4 | tfrapDiagVnipIpAddr | 0 | 0 | This is the ip address for the given interface/index combination. This comes from the VniptTopologyTable. |
1.3.6.1.4.1.485.5.3.6.1.5 | tfrapDiagVLOOP | 0 | 0 | Controls execution of the Vnip Logical Loopback (VLOOP) test. VLOOP is designed as an intrusive test and customer data on the DLC… |
1.3.6.1.4.1.485.5.3.6.1.6 | tfrapDiagVBERT | 0 | 0 | Controls execution of the Vnip Virtual Bit Eror Rate (VBERT) test. VBERT is designed to be a non-intrusive test and will attempt… |
1.3.6.1.4.1.485.5.3.6.1.7 | tfrapDiagVBERTRate | 0 | 0 | Specifies the throughput bit rate applied by VBERT or VLOOP to the DLCI-under-test. For DTE Rates or configured CIR up to 64K the… |
1.3.6.1.4.1.485.5.3.6.1.8 | tfrapDiagVBERTSize | 0 | 0 | Specifies the size of framed data that will be used during the VBERT test, measured in Bytes. (64) 64-byte frames (128) 128-byte f… |
1.3.6.1.4.1.485.5.3.6.1.9 | tfrapDiagVBERTPktPercent | 0 | 0 | Specifies percentage of VBERT packets that will have the Frame Relay Discard Eligibility bit set. Frames with this bit set may be… |
1.3.6.1.4.1.485.5.3.6.1.10 | tfrapDiagVBERTTestPeriod | 0 | 0 | Specifies the duration of a VBERT test. Note that VBERT is subjected to the unit's Loopback Timer and will be terminated by which… |