Controls execution of the Vnip Virtual Bit Eror Rate (VBERT) test.
VBERT is designed to be a non-intrusive test and will attempt to
statistically multiplex VBERT test data and customer data on the
DLCI-under-test. However, VBERT data is given priority over customer
data when the selected VBERT volume causes internal congestion.
The test is run using the profile configured within this table.
(1) start test
(2) stop test (override VBERT test duration)
Parsed from file TFRAP.MIB.txt
Company: None
Module: TFRAP-MIB
Controls execution of the Vnip Virtual Bit Eror Rate (VBERT) test.
VBERT is designed to be a non-intrusive test and will attempt to
statistically multiplex VBERT test data and customer data on the
DLCI-under-test. However, VBERT data is given priority over customer
data when the selected VBERT volume causes internal congestion.
The test is run using the profile configured within this table.
(1) start test
(2) stop test (override VBERT test duration)
Parsed from file TFRAP-MIB.mib
Module: TFRAP-MIB
Vendor: Sync Research, Inc.
Module: TFRAP-MIB
[Automatically extracted from oidview.com]
tfrapDiagVBERT OBJECT-TYPE SYNTAX INTEGER { start (1), stop (2) } ACCESS write-only STATUS mandatory DESCRIPTION "Controls execution of the Vnip Virtual Bit Eror Rate (VBERT) test. VBERT is designed to be a non-intrusive test and will attempt to statistically multiplex VBERT test data and customer data on the DLCI-under-test. However, VBERT data is given priority over customer data when the selected VBERT volume causes internal congestion. The test is run using the profile configured within this table. (1) start test (2) stop test (override VBERT test duration)" ::= { tfrapDiagVnipEntry 6 }
tfrapDiagVBERT OBJECT-TYPE SYNTAX INTEGER { start (1), stop (2) } ACCESS write-only STATUS mandatory DESCRIPTION "Controls execution of the Vnip Virtual Bit Eror Rate (VBERT) test. VBERT is designed to be a non-intrusive test and will attempt to statistically multiplex VBERT test data and customer data on the DLCI-under-test. However, VBERT data is given priority over customer data when the selected VBERT volume causes internal congestion. The test is run using the profile configured within this table. (1) start test (2) stop test (override VBERT test duration)" ::= { tfrapDiagVnipEntry 6 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.485.5.3.6.1.1 | tfrapDiagVnipInterface | 0 | 0 | The interface out which a PVC-based VNIP diagnostic will be run. This must be an interface with a valid and stable VNIP topology … |
| 1.3.6.1.4.1.485.5.3.6.1.2 | tfrapDiagVnipIndex | 0 | 0 | The index to the external VNIP peer as presented by the VNIP topology database for the given interface. Refer to VnipTopologyTabl… |
| 1.3.6.1.4.1.485.5.3.6.1.3 | tfrapDiagVnipDlci | 0 | 0 | This is the DLCI value for the given interface/index combination. This comes from the VniptTopologyTable. |
| 1.3.6.1.4.1.485.5.3.6.1.4 | tfrapDiagVnipIpAddr | 0 | 0 | This is the ip address for the given interface/index combination. This comes from the VniptTopologyTable. |
| 1.3.6.1.4.1.485.5.3.6.1.5 | tfrapDiagVLOOP | 0 | 0 | Controls execution of the Vnip Logical Loopback (VLOOP) test. VLOOP is designed as an intrusive test and customer data on the DLC… |
| 1.3.6.1.4.1.485.5.3.6.1.7 | tfrapDiagVBERTRate | 0 | 0 | Specifies the throughput bit rate applied by VBERT or VLOOP to the DLCI-under-test. For DTE Rates or configured CIR up to 64K the… |
| 1.3.6.1.4.1.485.5.3.6.1.8 | tfrapDiagVBERTSize | 0 | 0 | Specifies the size of framed data that will be used during the VBERT test, measured in Bytes. (64) 64-byte frames (128) 128-byte f… |
| 1.3.6.1.4.1.485.5.3.6.1.9 | tfrapDiagVBERTPktPercent | 0 | 0 | Specifies percentage of VBERT packets that will have the Frame Relay Discard Eligibility bit set. Frames with this bit set may be… |
| 1.3.6.1.4.1.485.5.3.6.1.10 | tfrapDiagVBERTTestPeriod | 0 | 0 | Specifies the duration of a VBERT test. Note that VBERT is subjected to the unit's Loopback Timer and will be terminated by which… |