Address Resolution Dlcis determines which dlcis are
used for address resolution. The choices include
using the configured management dlci only (1), all
dlcis (2), all dlcis on the To-DCE port (3) or all
dlcis on the To-DTE port (4). In the last two cases,
the management dlci is used on the other port.
Multiple DLCI support only applies to piggyback mode;
in other management modes, only the configured
management dlci is used.
Parsed from file SFRAP.MIB.txt
Company: None
Module: SFRAP-MIB
Address Resolution Dlcis determines which dlcis are
used for address resolution. The choices include
using the configured management dlci only (1), all
dlcis (2), all dlcis on the To-DCE port (3) or all
dlcis on the To-DTE port (4). In the last two cases,
the management dlci is used on the other port.
Multiple DLCI support only applies to piggyback mode;
in other management modes, only the configured
management dlci is used.
Parsed from file SFRAP-MIB.mib
Module: SFRAP-MIB
Vendor: Sync Research, Inc.
Module: SFRAP-MIB
[Automatically extracted from oidview.com]
sfrapCfgFrAddrResDlcis OBJECT-TYPE SYNTAX INTEGER { single (1), multiple (2), todcemulti (3), todtemulti (4) } ACCESS read-write STATUS mandatory DESCRIPTION "Address Resolution Dlcis determines which dlcis are used for address resolution. The choices include using the configured management dlci only (1), all dlcis (2), all dlcis on the To-DCE port (3) or all dlcis on the To-DTE port (4). In the last two cases, the management dlci is used on the other port. Multiple DLCI support only applies to piggyback mode; in other management modes, only the configured management dlci is used." ::= { sfrapCfgFrTable 9 }
sfrapCfgFrAddrResDlcis OBJECT-TYPE SYNTAX INTEGER { single (1), multiple (2), todcemulti (3), todtemulti (4) } ACCESS read-write STATUS mandatory DESCRIPTION "Address Resolution Dlcis determines which dlcis are used for address resolution. The choices include using the configured management dlci only (1), all dlcis (2), all dlcis on the To-DCE port (3) or all dlcis on the To-DTE port (4). In the last two cases, the management dlci is used on the other port. Multiple DLCI support only applies to piggyback mode; in other management modes, only the configured management dlci is used." ::= { sfrapCfgFrTable 9 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.485.7.2.5.9.0 | sfrapCfgFrAddrResDlcis | 0 | 0 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.485.7.2.5.1 | sfrapCfgFrAddrLen | 1 | 1 | Defines the size of the DLCI address field of the Frame Relay header. This setting must correspond to the Frame Relay transmissio… |
| 1.3.6.1.4.1.485.7.2.5.2 | sfrapCfgFrCrcMode | 1 | 1 | This defines the manner in which the unit handles HDLC protocol errors (crc errors) in a Frame Relay application. If Discard is s… |
| 1.3.6.1.4.1.485.7.2.5.3 | sfrapCfgFrLmiType | 1 | 1 | The LMI type used in a Frame Relay application. This setting must match the attached Frame Relay device configuration. Annex-A an… |
| 1.3.6.1.4.1.485.7.2.5.4 | sfrapCfgFrLmiInactivityTimeout | 1 | 1 | Timer used by the unit to determine that an attached device is not participating in the LMI protocol and that the unit should att… |
| 1.3.6.1.4.1.485.7.2.5.5 | sfrapCfgFrLmiKeepaliveTimeout | 1 | 1 | Timer used by the unit to determine the frequency at which Status Enquiries are issued during LMI sourcing states where the unit… |
| 1.3.6.1.4.1.485.7.2.5.6 | sfrapCfgFrAddrResMode | 1 | 1 | Enable ARP (2), INARP (3), both (4), or neither (1). |
| 1.3.6.1.4.1.485.7.2.5.7 | sfrapCfgFrAddrResInarpTimer | 1 | 1 | The frequency of INARP requests in seconds from 5 seconds to 86400 seconds (24 hours). |
| 1.3.6.1.4.1.485.7.2.5.8 | sfrapCfgFrLmiFullStatus | 1 | 1 | Timer used by the unit to determine if an LMI Full Status Report is missing. In the absence of a Full Status report for the durat… |