Vendor: Juniper Networks/Unisphere
Module: Juniper-BGP-MIB
[Automatically extracted from oidview.com]
usdBgpGeneralGroup OBJECT IDENTIFIER ::= { usdBgpObjects 1 }
usdBgpGeneralGroup OBJECT IDENTIFIER ::= { usdBgpObjects 1 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.4874.2.2.29.1.1.1 | juniBgpLocalAsNumber, usdBgpLocalAsNumber | 1 | 1 | The local autonomous system number. This object cannot be modified if BGP is enabled. |
1.3.6.1.4.1.4874.2.2.29.1.1.2 | juniBgpEnabled, usdBgpEnabled | 1 | 1 | Set this object to true(1) in order to have BGP router enabled. |
1.3.6.1.4.1.4874.2.2.29.1.1.3 | juniBgpIdentifier, usdBgpIdentifier | 1 | 1 | The BGP identifier of the local system. The identifier is the system router ID by default. |
1.3.6.1.4.1.4874.2.2.29.1.1.4 | juniBgpAlwaysCompareMed, usdBgpAlwaysCompareMed | 1 | 1 | Set this object to true(1) in order to compare metrics for paths from neighors of different ASs. |
1.3.6.1.4.1.4874.2.2.29.1.1.5 | juniBgpDefaultLocalPreference, usdBgpDefaultLocalPreference | 1 | 1 | The default local preference. |
1.3.6.1.4.1.4874.2.2.29.1.1.6 | juniBgpEqualCostLimit, usdBgpEqualCostLimit | 1 | 1 | The maximum equal cost paths to store in routing table. |
1.3.6.1.4.1.4874.2.2.29.1.1.7 | juniBgpClientToClientReflection, usdBgpClientToClientReflection | 1 | 1 | Set this object to true(1) in order to have client-to-client route reflection enabled. |
1.3.6.1.4.1.4874.2.2.29.1.1.8 | juniBgpClusterId, usdBgpClusterId | 1 | 1 | The cluster ID. When this object is zero, the router ID will be used. |
1.3.6.1.4.1.4874.2.2.29.1.1.9 | juniBgpConfederationId, usdBgpConfederationId | 1 | 1 | The confederation ID. When this object is zero, the router is not in a confederation. |
1.3.6.1.4.1.4874.2.2.29.1.1.10 | juniBgpMissingAsWorst, usdBgpMissingAsWorst | 1 | 1 | If this object is set to true(1) routes without a MED attribute are considered worse than routes with a MED attribute. If this … |
1.3.6.1.4.1.4874.2.2.29.1.1.11 | juniBgpResetAllConnectionType, usdBgpResetAllConnectionType | 1 | 1 | Writing a value to this object causes all sessions to all peers to be cleared; the value determines what type of clear is execut… |
1.3.6.1.4.1.4874.2.2.29.1.1.12 | juniBgpAdvertiseInactive, usdBgpAdvertiseInactive | 1 | 1 | Set this object to true(1) in order to propagate received BGP routes which are not the best route in the IP forwarding table. |
1.3.6.1.4.1.4874.2.2.29.1.1.13 | juniBgpEnforceFirstAs, usdBgpEnforceFirstAs | 1 | 1 | Set this object to true(1) in order to check whether the first AS number in the AS-path in routes from EBGP peers is consistent … |
1.3.6.1.4.1.4874.2.2.29.1.1.14 | juniBgpConfedCompareMed, usdBgpConfedCompareMed | 1 | 1 | Set this object to true(1) in order to compare metrics for paths from neighors of different sub-ASs in the same confederation. |
1.3.6.1.4.1.4874.2.2.29.1.1.15 | juniBgpGlobalRetryInterval, usdBgpGlobalRetryInterval | 1 | 1 | The default number of seconds before BGP retries to establish an outgoing BGP session. |
1.3.6.1.4.1.4874.2.2.29.1.1.16 | juniBgpGlobalConfigKeepAliveInterval, usdBgpGlobalConfigKeepAliveInterval | 1 | 1 | Default time interval in seconds for the KeepAlive timer for all peers. Zero means don't send KeepAlive messages. |
1.3.6.1.4.1.4874.2.2.29.1.1.17 | juniBgpGlobalConfigHoldTime, usdBgpGlobalConfigHoldTime | 1 | 1 | Default time interval in seconds for the Hold timer for all peers. Zero means don't expect KeepAlive message to be received. |
1.3.6.1.4.1.4874.2.2.29.1.1.18 | juniBgpGlobalAsOriginationInterval, usdBgpGlobalAsOriginationInterval | 1 | 1 | Default time interval in seconds for the MinASOriginationInterval timer for all peers. |
1.3.6.1.4.1.4874.2.2.29.1.1.19 | juniBgpExternalAdvertisementInterval, usdBgpExternalAdvertisementInterval | 1 | 1 | Default time interval in seconds for the MinRouteAdvertisementInterval timer for all external peers. |
1.3.6.1.4.1.4874.2.2.29.1.1.20 | juniBgpGlobalRibOutEnabled, usdBgpGlobalRibOutEnabled | 1 | 1 | Set this object to true(1) in order to enable RIB-out by default for all peers, or to false(2) to disable RIB-out by default for… |
1.3.6.1.4.1.4874.2.2.29.1.1.21 | juniBgpOverloadShutdown, usdBgpOverloadShutdown | 1 | 1 | Set this object to true(1) for BGP to shut itself down when it runs out of memory. Set this object to false(2) for BGP to conti… |
1.3.6.1.4.1.4874.2.2.29.1.1.22 | juniBgpLogNeighborChanges, usdBgpLogNeighborChanges | 1 | 1 | Set this object to true(1) for BGP log a message whenever a peer enters or leaves the established state. |
1.3.6.1.4.1.4874.2.2.29.1.1.23 | juniBgpFastExternalFallover, usdBgpFastExternalFallover | 1 | 1 | Set this object to true(1) for BGP to immediately bring down any directly adjacent EBGP session on a link down. |
1.3.6.1.4.1.4874.2.2.29.1.1.24 | juniBgpInternalAdvertisementInterval, usdBgpInternalAdvertisementInterval | 1 | 1 | Default time interval in seconds for the MinRouteAdvertisementInterval timer for all internal peers. |
1.3.6.1.4.1.4874.2.2.29.1.1.25 | juniBgpMaxAsLimit, usdBgpMaxAsLimit | 1 | 1 | Maximum length of received AS-path. Received routes with an AS-path longer than this are not placed in the IP forwarding table … |
1.3.6.1.4.1.4874.2.2.29.1.1.26 | juniBgpOperationalState, usdBgpOperationalState | 1 | 1 | The BGP instance operational state. |
1.3.6.1.4.1.4874.2.2.29.1.1.27 | juniBgpPreviousOperationalState, usdBgpPreviousOperationalState | 1 | 1 | The BGP instance previous operational state. |
1.3.6.1.4.1.4874.2.2.29.1.1.28 | juniBgpAutomaticRouteTargetFilter, usdBgpAutomaticRouteTargetFilter | 1 | 1 | Set this object to true(1) for BGP to enable automatic route-target filtering. |
1.3.6.1.4.1.4874.2.2.29.1.1.29 | juniBgpDefaultIPv4Unicast, usdBgpDefaultIPv4Unicast | 1 | 1 | Set this object to true(1) for BGP to automatically activate peers in the IPv4 unicast address family. |
1.3.6.1.4.1.4874.2.2.29.1.1.30 | juniBgpRedistributeInternal, usdBgpRedistributeInternal | 1 | 1 | Set this object to true(1) for BGP to automatically redistribute iBGP routes to IGP protocols. |
1.3.6.1.4.1.4874.2.2.29.1.1.31 | juniBgpFourOctetLocalAsNumber | 1 | 1 | The four-octet local autonomous system number. This attribute replaces the old two-octet local autonomous system number. |
1.3.6.1.4.1.4874.2.2.29.1.1.32 | juniBgpConfederationPeersFilterList | 1 | 1 | The confederation peers filter-list contains the name of an as-path access-list. Every neighbor whose remote-AS number matches … |
1.3.6.1.4.1.4874.2.2.29.1.1.33 | juniBgpUnconfiguredAttributes, usdBgpUnconfiguredAttributes | 1 | 1 | On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e… |
1.3.6.1.4.1.4874.2.2.29.1.1.34 | juniBgpAdvertiseBestExternalToInternal | 1 | 1 | If this object is set to true(1) then BGP advertises the best route received from external (and confederation) peers to internal… |
1.3.6.1.4.1.4874.2.2.29.1.1.35 | juniBgpGracefulRestartEnabled | 1 | 1 | Set this object to true(1) to enable BGP graceful restart. |
1.3.6.1.4.1.4874.2.2.29.1.1.36 | juniBgpGracefulRestartRestartTime | 1 | 1 | The restart-time advertised in graceful-restart capabilities sent to all peers. This is the estimated time (in seconds) it will … |
1.3.6.1.4.1.4874.2.2.29.1.1.37 | juniBgpGracefulRestartStalePathsTime | 1 | 1 | The maximum amount of time in seconds we keep stale routes after a session goes down. This value is used for all peers unless it… |
1.3.6.1.4.1.4874.2.2.29.1.1.38 | juniBgpGracefulRestartPathSelectionDeferTimeLimit | 1 | 1 | The maximum amount of time in seconds route selection is deferred after a restart. |
1.3.6.1.4.1.4874.2.2.29.1.1.39 | juniBgpPlatformSupportsNonStopForwarding | 1 | 1 | Does this platform support non-stop forwarding? |
1.3.6.1.4.1.4874.2.2.29.1.1.40 | juniBgpDeviceCanPreserveForwardingState | 1 | 1 | Is this router at this moment able to do a graceful restart (i.e. is it able to switch over from the primary controller to the s… |
1.3.6.1.4.1.4874.2.2.29.1.1.41 | juniBgpLastRestartWasGraceful | 1 | 1 | Was the most recent restart graceful? (i.e. was forwarding state preserved on the line cards during the most recent switch-over f… |
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.4874.2.2.29.1.2 | juniBgpRouteTableStatisticsGroup, usdBgpRouteTableStatisticsGroup | 11 | 22 | None |
1.3.6.1.4.1.4874.2.2.29.1.3 | juniBgpConfederationPeerTable, usdBgpConfederationPeerTable | 1 | 3 | The Unisphere BGP Confederation Peer Table describes the BGP-specific characteristics of confederation peers. |
1.3.6.1.4.1.4874.2.2.29.1.4 | juniBgpPeerTable, usdBgpPeerTable | 1 | 86 | The Unisphere BGP Peer Table describes the BGP-specific characteristics of peers. |
1.3.6.1.4.1.4874.2.2.29.1.5 | juniBgpPeerProposedAfiSafiPeerTable, usdBgpPeerProposedAfiSafiPeerTable | 1 | 6 | The Unisphere BGP PeerProposedAfiSafi Peer Table describes the BGP-specific AFI and SAFIs a peer proposed. |
1.3.6.1.4.1.4874.2.2.29.1.6 | juniBgpLocalProposedAfiSafiPeerTable, usdBgpLocalProposedAfiSafiPeerTable | 1 | 6 | The Unisphere BGP LocalProposedAfiSafi Peer Table describes the BGP-specific AFI and SAFIs proposed to the peer. |
1.3.6.1.4.1.4874.2.2.29.1.7 | juniBgpExchangedAfiSafiPeerTable, usdBgpExchangedAfiSafiPeerTable | 1 | 6 | The Unisphere BGP PeerExchangedAfiSafi Peer Table describes the BGP-specific AFI and SAFIs a peer exchanged. |
1.3.6.1.4.1.4874.2.2.29.1.8 | juniBgpPeerAddressFamilyTable, usdBgpPeerAddressFamilyTable | 1 | 56 | The Unisphere BGP Peer Address Family Table describes the BGP-specific attributes of an Address Family for a peer. |
1.3.6.1.4.1.4874.2.2.29.1.9 | juniBgpPeerGroupTable, usdBgpPeerGroupTable | 1 | 46 | The Unisphere BGP Peer Group Table describes the BGP-specific characteristics of peer groups. |
1.3.6.1.4.1.4874.2.2.29.1.10 | juniBgpPeerGroupAddressFamilyTable, usdBgpPeerGroupAddressFamilyTable | 1 | 39 | The Unisphere BGP Peer Group Address Family Table describes the BGP-specific attributes of an Address Family for a peer group. |
1.3.6.1.4.1.4874.2.2.29.1.12 | juniBgpRouteFlapHistoryTable, usdBgpRouteFlapHistoryTable | 1 | 9 | The obsolete BGP Route Flap History Table contained information about recorded route flap events. This table has been replaced … |
1.3.6.1.4.1.4874.2.2.29.1.13 | juniBgpRouteTable, usdBgpRouteTable | 1 | 38 | The obsolete BGP-4 Received Path Attribute Table contained additional information about paths to destination networks received f… |
1.3.6.1.4.1.4874.2.2.29.1.14 | juniBgpRouteCommunityTable, usdBgpRouteCommunityTable | 1 | 2 | The obsolete BGP-4 Path Community Table contained information about communities within destination networks received from all BG… |
1.3.6.1.4.1.4874.2.2.29.1.15 | juniBgpRouteClusterIdTable, usdBgpRouteClusterIdTable | 1 | 2 | The obsolete BGP-4 Path ClusterId Table contained information about router reflector cluster IDs. This table has been replaced … |
1.3.6.1.4.1.4874.2.2.29.1.16 | juniBgpNetworkTable, usdBgpNetworkTable | 1 | 12 | The BGP Network Table controls what networks are originated by this BGP router. |
1.3.6.1.4.1.4874.2.2.29.1.17 | juniBgpAggregateTable, usdBgpAggregateTable | 1 | 13 | The BGP Aggregate Table controls the consolidation of route information. |
1.3.6.1.4.1.4874.2.2.29.1.18 | juniBgpVrfTable, usdBgpVrfTable | 1 | 16 | juniBgpVrftable |
1.3.6.1.4.1.4874.2.2.29.1.19 | juniBgpAddressFamilyTable, usdBgpAddressFamilyTable | 1 | 28 | The BGP AddressFamily Entry describes BGP-specific characteristics of one AddressFamily. |
1.3.6.1.4.1.4874.2.2.29.1.20 | juniBgpStorageGroup, usdBgpStorageGroup | 42 | 84 | None |
1.3.6.1.4.1.4874.2.2.29.1.22 | juniBgpRouteExtendedCommunityTable, usdBgpRouteExtendedCommunityTable | 1 | 2 | The obsolete BGP-4 Path Extended Community Table contained information about communities within destination networks received fr… |
1.3.6.1.4.1.4874.2.2.29.1.23 | juniBgpNewRouteTable, usdBgpNewRouteTable | 1 | 43 | The BGP-4 Received Path Attribute Table contains additional information about paths to destination networks received from all BG… |
1.3.6.1.4.1.4874.2.2.29.1.24 | juniBgpNewRouteFlapHistoryTable, usdBgpNewRouteFlapHistoryTable | 1 | 9 | The BGP Route Flap History Table contains information about recorded route flap events. |
1.3.6.1.4.1.4874.2.2.29.1.25 | juniBgpNewRouteCommunityTable, usdBgpNewRouteCommunityTable | 1 | 2 | The BGP-4 Path Community Table contains information about communities within destination networks received from all BGP4 peers. |
1.3.6.1.4.1.4874.2.2.29.1.26 | juniBgpNewRouteExtendedCommunityTable, usdBgpNewRouteExtendedCommunityTable | 1 | 2 | The BGP-4 Path Extended Community Table contains information about communities within destination networks received from all BGP… |
1.3.6.1.4.1.4874.2.2.29.1.27 | juniBgpNewRouteClusterIdTable, usdBgpNewRouteClusterIdTable | 1 | 2 | The BGP-4 Path ClusterId Table contains information about router reflector cluster IDs. |
1.3.6.1.4.1.4874.2.2.29.1.28 | juniBgpFourOctetConfederationPeerTable | 1 | 3 | The BGP New Confederation Peer Table describes the BGP-specific characteristics of confederation peers using four-octet AS-numbe… |
1.3.6.1.4.1.4874.2.2.29.1.29 | juniBgpPeerDynamicCapabilityTable | 1 | 6 | The BGP PeerDynamicCapbility Table describes which dynamic capbilities we proposed to the peer, which the peer proposed to us, a… |
1.3.6.1.4.1.4874.2.2.29.1.30 | juniBgpPeerAddressFamilyConditionalAdvTable | 1 | 7 | The Juniper BGP Peer Address Family Conditional Advertisement Table describes the BGP conditional advertisement attributes in an… |
1.3.6.1.4.1.4874.2.2.29.1.31 | juniBgpPeerGroupAddressFamilyConditionalAdvTable | 1 | 7 | The Juniper BGP Peer Group Address Family Conditional Advertisement Table describes the BGP conditional advertisement attributes… |