The planned configuration information for a specific BOP/COP port.
Parsed from file CXBOPIO.MIB.txt
Company: None
Module: CXBOPIO-MIB
The planned configuration information for a specific BOP/COP port.
Parsed from file CXBOPIO-MIB.mib
Module: CXBOPIO-MIB
Vendor: Memotec Communications
Module: CXBOPIO-MIB
[Automatically extracted from oidview.com]
bopSapAdmEntry OBJECT-TYPE SYNTAX BopSapAdmEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The planned configuration information for a specific BOP/COP port." INDEX { bopSapAdmNumber } ::= { bopSapAdmTable 1 }
bopSapAdmEntry OBJECT-TYPE SYNTAX BopSapAdmEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The planned configuration information for a specific BOP/COP port." INDEX { bopSapAdmNumber } ::= { bopSapAdmTable 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.495.2.1.6.36.2.1.1 | bopSapAdmNumber | 0 | 0 | Defines the SAP ID using 2,3 or 4 digits. The first digit (A) is the slot #, the second digit (B) is the port #, and the remaini… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.2 | bopSapAdmAlias | 0 | 0 | Determines the textual name uniquely identifying this SAP in the BOP Driver software layer. Ranges of Values: 0-16 alphanumeric c… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.3 | bopSapAdmProtocol | 0 | 0 | Determines if the port is HDLC or Bisync. Only HDLC is supported by ISDN and T1/E1 ports. Indicates in the operative configuration… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.5 | bopSapAdmPortClockSource | 0 | 0 | Determines the bit-rate clock source of the port. Options: internal (1): Tx and Rx clocks are internally generated external (2): T… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.6 | bopSapAdmPortSpeed | 0 | 0 | Indicates the input and output speed in bits per second of the port. Note: This value is meaningful only if 'bopSapAdmPortClockSo… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.7 | bopSapAdmPortDuplex | 0 | 0 | Determines whether the port communicates simultaneously in both directions (full-duplex) or alternates between directions (half-… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.8 | bopSapAdmPortMaxFrameSize | 0 | 0 | Determines the maximum frame size supported by the port. Ranges of Values: 32-9000 Default Value: 1,600 (512 for ISDN) Configurati… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.9 | bopSapAdmPortDataEncoding | 0 | 0 | Determines the data formatting and encoding used by the port. Options: nrz (1): NRZ (locked for ISDN 'D' channel; ISDN 'B' channe… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.10 | bopSapAdmPortIdleCondition | 0 | 0 | Determines the idle line condition supported by the port. Options: flags (1): flags marks (2): marks as400 (3): AS400 Default Value:… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.11 | bopSapAdmPortPreAmbleLength | 0 | 0 | Determines the minimum number of flags or sync pairs that will be inserted between frames by the port's transmitter. For HDLC fra… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.12 | bopSapAdmPortFlagSharing | 0 | 0 | Determines whether back-to-back transmit frames will have a flag in common This value is meaningful only if 'bopSapAdmPortPreAmb… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.13 | bopSapAdmPortFilterMask | 0 | 0 | Determines which bits of the 8-bit HDLC address will be used for address filtering. Note: When a bit is set to '1', the position o… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.14 | bopSapAdmPortFilterAddress1 | 0 | 0 | Determines one of four 8-bit addresses used for address filtering. Ranges of Values: 0-255 Default Value: 126 Configuration Change… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.15 | bopSapAdmPortFilterAddress2 | 0 | 0 | Determines one of four 8-bit addresses used for address filtering. Ranges of Values: 0-255 Default Value: 126 Configuration Change… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.16 | bopSapAdmPortFilterAddress3 | 0 | 0 | Determines one of four 8-bit addresses used for address filtering. Ranges of Values: 0-255 Default Value: 126 Configuration Change… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.17 | bopSapAdmPortFilterAddress4 | 0 | 0 | Determines one of four 8-bit addresses used for address filtering. Ranges of Values: 0-255 Default Value: 126 Configuration Change… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.18 | bopSapAdmPortCrc | 0 | 0 | Determines which algorithm is used for error detection. Options: crc-ccitt (1): CRC-ITU-T (uses X15+X12+X5+1 polynomial; ITU-T fo… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.19 | bopSapAdmPortDtrUpTimer | 0 | 0 | Determines the time in seconds that the port must wait for DCD (DTR if DCE) after raising DTR (DCD if DCE) to determine if a con… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.20 | bopSapAdmPortTxWindow | 0 | 0 | Determines the maximum number of buffers that may be queued onto the port driver (for transmission) by the associated upper laye… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.21 | bopSapAdmPortThreshBandwidth | 0 | 0 | Determines the value of the minimum critical bandwidth that will determine whether Frame Relay should filter certain restricted … |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.22 | bopSapAdmPortDialMode | 0 | 0 | Identifies the operation mode when setting up connections. Options: dial-in-only (1): Only accept incoming calls; Will not make… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.28 | bopSapAdmPortLoopback | 0 | 0 | Determines whether loopback is enabled and what kind of loopback is enabled. Options: none (1): Loopback is not enabled local (2)… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.29 | bopSapAdmPortSignalSamplingPeriod | 0 | 0 | Determines the sampling period in 100 millisecond increments used to sample detectable signals. Ranges of Values: 3-100 (locked a… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.30 | bopSapAdmPortDcdDtrSignalSamples | 0 | 0 | Determines the active number of sampling periods that this port must wait before validating DCD (DTR if DCE). This object has no … |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.31 | bopSapAdmPortCtsRtsSignalSamples | 0 | 0 | Determines the active number of sampling periods that this port must wait before validating CTS (RTS if DCE). This object has no … |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.32 | bopSapAdmPortDsrDrsSignalSamples | 0 | 0 | Determines the active number of sampling periods that this port must wait before validating DSR (DRS if DCE). This object has no … |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.33 | bopSapAdmPortTmLlSignalSamples | 0 | 0 | Determines the active number of sampling periods that this port must wait before validating TM (LL if DCE). This object has no me… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.34 | bopSapAdmPortRiRlSignalSamples | 0 | 0 | Determines the active number of sampling periods that this port must wait before validating RI (RL if DCE). This object has no me… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.35 | bopSapAdmPortStatisticsTimer | 0 | 0 | Determines the period in seconds during which BOP performance statistics are measured. Note: If set to zero, BOP performance stat… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.36 | bopSapAdmPortCarrierAction | 0 | 0 | Determines if the port driver informs it's associated upper layer that service is no longer available following loss of DCD if D… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.37 | bopSapAdmPortDataGenerator | 0 | 0 | Determines whether the port will act as an internal data generator. Options: disabled (1): port is not a data generator enabled (… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.38 | bopSapAdmPortGenFrames | 0 | 0 | Determines the number of frames that the port configured as an internal data generator will generate at one time. Ranges of Value… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.39 | bopSapAdmPortGenFrameSize | 0 | 0 | Determines the size in bytes of internally generated frames (excluding flags). Ranges of Values: 2-65535 Note: When set to zero, … |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.40 | bopSapAdmPortGenFrameHeader | 0 | 0 | Determines the 16-bit header that will be inserted in the first two octets after the opening flag of each internally generated f… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.45 | bopSapAdmCodeSet | 0 | 0 | Determines in the administrative configuration the code used by the port associated with this SAP to communicate to the Bisync dev… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.46 | bopSapAdmParity | 0 | 0 | Indicates the parity used to communicate with the Bisync device Options: (1) none: No parity (2) odd: Odd parity (3) even: Even… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.47 | bopAdmPortTrap | 0 | 0 | Determines whether this port produces a 'bopPortStatusChange' trap which can be retrieved by SNMP network management. Options: dis… |
| 1.3.6.1.4.1.495.2.1.6.36.2.1.48 | bopAdmTxClockTrap | 0 | 0 | Determines whether this port produces a 'bopTxClockStatusChange' trap which can be retrieved by SNMP network management. Options:… |