A mibanswerProfile entry containing objects that
maps to the parameters of mibanswerProfile profile.
Parsed from file mibanswer.mib.txt
Company: None
Module: ASCEND-MIBANSWERPROFILE-MIB
A mibanswerProfile entry containing objects that
maps to the parameters of mibanswerProfile profile.
Parsed from file ASCEND-MIBANSWER-MIB.mib
Module: ASCEND-MIBANSWER-MIB
Vendor: Ascend Communications Inc.
Module: ASCEND-MIBANSWER-MIB
[Automatically extracted from oidview.com]
mibanswerProfileEntry OBJECT-TYPE SYNTAX MibanswerProfileEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A mibanswerProfile entry containing objects that maps to the parameters of mibanswerProfile profile." INDEX { answerProfile__index__ } ::= { mibanswerProfileTable 1 }
mibanswerProfileEntry OBJECT-TYPE SYNTAX MibanswerProfileEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A mibanswerProfile entry containing objects that maps to the parameters of mibanswerProfile profile." INDEX { answerProfile-Index-o } ::= { mibanswerProfileTable 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.529.23.3.1.1.1 | answerProfile-Index-o, answerProfile__index__ | 0 | 0 | None |
| 1.3.6.1.4.1.529.23.3.1.1.2 | answerProfile-UseAnswerForAllDefaults, answerProfile__use_answer_for_all_defaults | 0 | 0 | When set to Yes, this profile will provide the default values for fields when building profiles. When set to No the factory pro… |
| 1.3.6.1.4.1.529.23.3.1.1.3 | answerProfile-Force56kbps, answerProfile__force_56kbps | 0 | 0 | If yes then inbound 64 kbps calls are connected at 56 kbps. |
| 1.3.6.1.4.1.529.23.3.1.1.4 | answerProfile-ProfilesRequired, answerProfile__profiles_required | 0 | 0 | Unused when incoming authentication is used. When authentication is not used a No value in this field indicates that we will cr… |
| 1.3.6.1.4.1.529.23.3.1.1.5 | answerProfile-ClidAuthMode, answerProfile__clid_auth_mode | 0 | 0 | Specifies how calling line identification (CLID) will be used for incoming call authentication. |
| 1.3.6.1.4.1.529.23.3.1.1.6 | answerProfile-PppAnswer-Enabled, answerProfile__ppp_answer__enabled | 0 | 0 | Set to Yes to enable incoming PPP calls. This includes the PPP variants, MP and MPP. |
| 1.3.6.1.4.1.529.23.3.1.1.7 | answerProfile-PppAnswer-ReceiveAuthMode, answerProfile__ppp_answer__receive_auth_mode | 0 | 0 | The type of PPP authentication to use for incoming calls. |
| 1.3.6.1.4.1.529.23.3.1.1.8 | answerProfile-PppAnswer-DisconnectOnAuthTimeout, answerProfile__ppp_answer__disconnect_on_auth_timeout | 0 | 0 | ???. |
| 1.3.6.1.4.1.529.23.3.1.1.9 | answerProfile-PppAnswer-BridgingGroup, answerProfile__ppp_answer__bridging_group | 0 | 0 | The default bridging group. Interfaces with the same bridging group can bridge to each other. Set to 0 to disable bridging. |
| 1.3.6.1.4.1.529.23.3.1.1.10 | answerProfile-PppAnswer-LinkCompression, answerProfile__ppp_answer__link_compression | 0 | 0 | The default type of link compression to use for PPP, MP, and MPP calls. |
| 1.3.6.1.4.1.529.23.3.1.1.11 | answerProfile-PppAnswer-Mru, answerProfile__ppp_answer__mru | 0 | 0 | The Maximum Receive Unit, i.e. the largest frame we will accept. |
| 1.3.6.1.4.1.529.23.3.1.1.12 | answerProfile-PppAnswer-Lqm, answerProfile__ppp_answer__lqm | 0 | 0 | Link Quality Monitoring. Set to Yes to enable the PPP LQM protocol. |
| 1.3.6.1.4.1.529.23.3.1.1.13 | answerProfile-PppAnswer-LqmMinimumPeriod, answerProfile__ppp_answer__lqm_minimum_period | 0 | 0 | The minimum period, in 1/100 of a second, that we will accept/send link quality monitoring packets. |
| 1.3.6.1.4.1.529.23.3.1.1.14 | answerProfile-PppAnswer-LqmMaximumPeriod, answerProfile__ppp_answer__lqm_maximum_period | 0 | 0 | The maximum period, in 1/100 of a second, that we will accept/send link quality monitoring packets. |
| 1.3.6.1.4.1.529.23.3.1.1.15 | answerProfile-MpAnswer-Enabled, answerProfile__mp_answer__enabled | 0 | 0 | Set to Yes to enable incoming MP calls. This includes the MP variant, MPP. |
| 1.3.6.1.4.1.529.23.3.1.1.16 | answerProfile-MpAnswer-MinimumChannels, answerProfile__mp_answer__minimum_channels | 0 | 0 | The default value for the minimum number of channels in a multi-channel call. |
| 1.3.6.1.4.1.529.23.3.1.1.17 | answerProfile-MpAnswer-MaximumChannels, answerProfile__mp_answer__maximum_channels | 0 | 0 | The default value for the maximum number of channels in a multi-channel call. |
| 1.3.6.1.4.1.529.23.3.1.1.18 | answerProfile-MpAnswer-BacpEnable, answerProfile__mp_answer__bacp_enable | 0 | 0 | Enable Bandwidth Allocation Control Protocol (BACP). |
| 1.3.6.1.4.1.529.23.3.1.1.19 | answerProfile-MppAnswer-Enabled, answerProfile__mpp_answer__enabled | 0 | 0 | Set to Yes to enable incoming MPP calls. |
| 1.3.6.1.4.1.529.23.3.1.1.20 | answerProfile-MppAnswer-DynamicAlgorithm, answerProfile__mpp_answer__dynamic_algorithm | 0 | 0 | The algorithm to use to calculate the average link utilization. Bandwidth changes are performed on the average utilization, not… |
| 1.3.6.1.4.1.529.23.3.1.1.21 | answerProfile-MppAnswer-BandwidthMonitorDirection, answerProfile__mpp_answer__bandwidth_monitor_direction | 0 | 0 | The direction to monitor link utilization. A unit can monitor transmit, transmit and receive, or turn off monitoring entirely. |
| 1.3.6.1.4.1.529.23.3.1.1.22 | answerProfile-MppAnswer-IncrementChannelCount, answerProfile__mpp_answer__increment_channel_count | 0 | 0 | Number of channels to increment as a block. |
| 1.3.6.1.4.1.529.23.3.1.1.23 | answerProfile-MppAnswer-DecrementChannelCount, answerProfile__mpp_answer__decrement_channel_count | 0 | 0 | Number of channels to decrement as a block. |
| 1.3.6.1.4.1.529.23.3.1.1.24 | answerProfile-MppAnswer-SecondsHistory, answerProfile__mpp_answer__seconds_history | 0 | 0 | The number of seconds of history that link utilization is averaged over to make bandwidth changes. |
| 1.3.6.1.4.1.529.23.3.1.1.25 | answerProfile-MppAnswer-AddPersistence, answerProfile__mpp_answer__add_persistence | 0 | 0 | The number of seconds of that the average line utilization must exceed the target utilization before bandwidth will be added. |
| 1.3.6.1.4.1.529.23.3.1.1.26 | answerProfile-MppAnswer-SubPersistence, answerProfile__mpp_answer__sub_persistence | 0 | 0 | The number of seconds of that the average line utilization must fall below the target utilization before bandwidth will be redu… |
| 1.3.6.1.4.1.529.23.3.1.1.27 | answerProfile-MppAnswer-TargetUtilization, answerProfile__mpp_answer__target_utilization | 0 | 0 | The default value for the target utilization. Bandwidth changes occur when the average utilization exceeds or falls below this … |
| 1.3.6.1.4.1.529.23.3.1.1.28 | answerProfile-FrAnswer-Enabled, answerProfile__fr_answer__enabled | 0 | 0 | Set to yes to enable incoming FR calls. |
| 1.3.6.1.4.1.529.23.3.1.1.29 | answerProfile-TcpClearAnswer-Enabled, answerProfile__tcp_clear_answer__enabled | 0 | 0 | If enabled, incoming calls that match a local profile with a call management type of tcp-raw will automatically be connected vi… |
| 1.3.6.1.4.1.529.23.3.1.1.30 | answerProfile-AraAnswer-Enabled, answerProfile__ara_answer__enabled | 0 | 0 | Set to yes to enable incoming ARA calls. |
| 1.3.6.1.4.1.529.23.3.1.1.31 | answerProfile-V120Answer-Enabled, answerProfile__v120_answer__enabled | 0 | 0 | Set to yes to enable incoming V120 calls. |
| 1.3.6.1.4.1.529.23.3.1.1.32 | answerProfile-V120Answer-FrameLength, answerProfile__v120_answer__frame_length | 0 | 0 | The default frame length to use for incoming V.120 connections. |
| 1.3.6.1.4.1.529.23.3.1.1.33 | answerProfile-X25Answer-Enabled, answerProfile__x25_answer__enabled | 0 | 0 | If enabled, incoming calls that match a local profile with a call management type of x25 will be accepted. |
| 1.3.6.1.4.1.529.23.3.1.1.34 | answerProfile-X25Answer-X25Profile, answerProfile__x25_answer__x25_profile | 0 | 0 | Name of the x25 profile that this profile is associated with. |
| 1.3.6.1.4.1.529.23.3.1.1.35 | answerProfile-X25Answer-X3Profile, answerProfile__x25_answer__x3_profile | 0 | 0 | X.3 profile parameter index |
| 1.3.6.1.4.1.529.23.3.1.1.36 | answerProfile-X25Answer-MaxCalls, answerProfile__x25_answer__max_calls | 0 | 0 | Max number of unsuccessful calls |
| 1.3.6.1.4.1.529.23.3.1.1.37 | answerProfile-X25Answer-VcTimerEnable, answerProfile__x25_answer__vc_timer_enable | 0 | 0 | PAD VCE enable flag |
| 1.3.6.1.4.1.529.23.3.1.1.38 | answerProfile-X25Answer-AutoCallX121Address, answerProfile__x25_answer__auto_call_x121_address | 0 | 0 | X.121 address to auto-call upon session startup. |
| 1.3.6.1.4.1.529.23.3.1.1.39 | answerProfile-X25Answer-ReverseCharge, answerProfile__x25_answer__reverse_charge | 0 | 0 | Reverse charge request |
| 1.3.6.1.4.1.529.23.3.1.1.40 | answerProfile-X25Answer-X3CustomProf, answerProfile__x25_answer__x3_custom_prof | 0 | 0 | Custom profile enter a string for a custom X.3 profile if x3Prof says custom. |
| 1.3.6.1.4.1.529.23.3.1.1.41 | answerProfile__comb_answer__enabled | 0 | 0 | If enabled, incoming calls that match a local profile with a call management type of comb will be accepted. |
| 1.3.6.1.4.1.529.23.3.1.1.42 | answerProfile__comb_answer__password_required | 0 | 0 | If enabled, the far end must supply a password when initiating a call. |
| 1.3.6.1.4.1.529.23.3.1.1.43 | answerProfile__comb_answer__interval | 0 | 0 | The combinet link integrety interval. |
| 1.3.6.1.4.1.529.23.3.1.1.44 | answerProfile__comb_answer__compression | 0 | 0 | Should compression be used. |
| 1.3.6.1.4.1.529.23.3.1.1.45 | answerProfile-EuAnswer-EurawEnabled, answerProfile__eu_answer__euraw_enabled | 0 | 0 | Enable/disable the EUNET raw protocol. |
| 1.3.6.1.4.1.529.23.3.1.1.46 | answerProfile-EuAnswer-EuuiEnabled, answerProfile__eu_answer__euui_enabled | 0 | 0 | Enable/disable the EUNET UI protocol. |
| 1.3.6.1.4.1.529.23.3.1.1.47 | answerProfile-EuAnswer-DceAddr, answerProfile__eu_answer__dce_addr | 0 | 0 | The address of the DCE side of the link when the EUNET UI protocol is used. |
| 1.3.6.1.4.1.529.23.3.1.1.48 | answerProfile-EuAnswer-DteAddr, answerProfile__eu_answer__dte_addr | 0 | 0 | The address of the DTE side of the link when the EUNET UI protocol is used. |
| 1.3.6.1.4.1.529.23.3.1.1.49 | answerProfile-EuAnswer-Mru, answerProfile__eu_answer__mru | 0 | 0 | The Maximum Receive Unit, i.e. the largest frame we will accept when the EUNET UI protocol is used. |
| 1.3.6.1.4.1.529.23.3.1.1.50 | answerProfile-IpAnswer-Enabled, answerProfile__ip_answer__enabled | 0 | 0 | Set to yes to enable IP routing on incoming calls using encapsulation protocols that support IP routing. |
| 1.3.6.1.4.1.529.23.3.1.1.51 | answerProfile-IpAnswer-VjHeaderPrediction, answerProfile__ip_answer__vj_header_prediction | 0 | 0 | Set to yes to enable Van Jacobson IP header prediction to be negotiated on incoming calls using encapsulation protocols that su… |
| 1.3.6.1.4.1.529.23.3.1.1.52 | answerProfile-IpAnswer-AssignAddress, answerProfile__ip_answer__assign_address | 0 | 0 | Set to yes if this unit is configured with one or more pools of IP addresses that will be used as a source of addresses to assi… |
| 1.3.6.1.4.1.529.23.3.1.1.53 | answerProfile-IpAnswer-RoutingMetric, answerProfile__ip_answer__routing_metric | 0 | 0 | The default metric assigned to routes created for incoming calls. |
| 1.3.6.1.4.1.529.23.3.1.1.54 | answerProfile-IpxAnswer-Enabled, answerProfile__ipx_answer__enabled | 0 | 0 | Set to Yes to enable incoming IPX calls. |
| 1.3.6.1.4.1.529.23.3.1.1.55 | answerProfile-IpxAnswer-PeerMode, answerProfile__ipx_answer__peer_mode | 0 | 0 | Enable/disable full routing between peer or use the pool to assign a network number. |
| 1.3.6.1.4.1.529.23.3.1.1.56 | answerProfile-SessionInfo-CallFilter, answerProfile__session_info__call_filter | 0 | 0 | The name of the filter used to determine if a packet should cause the idle timer to be reset or, when the answer profile is use… |
| 1.3.6.1.4.1.529.23.3.1.1.57 | answerProfile-SessionInfo-DataFilter, answerProfile__session_info__data_filter | 0 | 0 | The name of the filter used to determine if packets should be forwarded or dropped. |
| 1.3.6.1.4.1.529.23.3.1.1.58 | answerProfile-SessionInfo-FilterPersistence, answerProfile__session_info__filter_persistence | 0 | 0 | Determines if filters should persist between calls. |
| 1.3.6.1.4.1.529.23.3.1.1.59 | answerProfile-SessionInfo-IdleTimer, answerProfile__session_info__idle_timer | 0 | 0 | The number of seconds of no activity before a call will be dropped. The value 0 disables the idle timer. |
| 1.3.6.1.4.1.529.23.3.1.1.60 | answerProfile-SessionInfo-TsIdleMode, answerProfile__session_info__ts_idle_mode | 0 | 0 | The method used to determine when the terminal server idle session timer is reset. |
| 1.3.6.1.4.1.529.23.3.1.1.61 | answerProfile-SessionInfo-TsIdleTimer, answerProfile__session_info__ts_idle_timer | 0 | 0 | The number of seconds of no activity as defined by the idle mode before a session will be terminated. |
| 1.3.6.1.4.1.529.23.3.1.1.62 | answerProfile-SessionInfo-MaxCallDuration, answerProfile__session_info__max_call_duration | 0 | 0 | The number of minutes of connect time before a call will be dropped. The value 0 disables the connection timer. |
| 1.3.6.1.4.1.529.23.3.1.1.63 | answerProfile-X75Answer-Enabled, answerProfile__x75_answer__enabled | 0 | 0 | Set to yes to enable incoming X75 calls. |
| 1.3.6.1.4.1.529.23.3.1.1.64 | answerProfile-X75Answer-KFramesOutstanding, answerProfile__x75_answer__k_frames_outstanding | 0 | 0 | Number of frames outstanding before we require an ack. Defaults to 7. |
| 1.3.6.1.4.1.529.23.3.1.1.65 | answerProfile-X75Answer-N2Retransmissions, answerProfile__x75_answer__n2_retransmissions | 0 | 0 | Number of retransmissions allowed. Defaults to 10. |
| 1.3.6.1.4.1.529.23.3.1.1.66 | answerProfile-X75Answer-T1RetranTimer, answerProfile__x75_answer__t1_retran_timer | 0 | 0 | Number of milliseconds between retransmissions. Defaults to 1000. |
| 1.3.6.1.4.1.529.23.3.1.1.67 | answerProfile-X75Answer-FrameLength, answerProfile__x75_answer__frame_length | 0 | 0 | Frame length to use for incoming X.75 connections. Defaults to 1024. |
| 1.3.6.1.4.1.529.23.3.1.1.68 | answerProfile-FramedOnly, answerProfile__framed_only | 0 | 0 | A profile can be restricted to only doing the framed commands (ppp, mpp, slip, and quit) by setting this to YES |
| 1.3.6.1.4.1.529.23.3.1.1.69 | answerProfile-Action-o, answerProfile__action__ | 0 | 0 | None |
| 1.3.6.1.4.1.529.23.3.1.1.70 | answerProfile-PppAnswer-CbcpEnabled, answerProfile__ppp_answer__cbcp_enabled | 0 | 0 | Enable Microsoft Callback Control Protocol Negotiation. |
| 1.3.6.1.4.1.529.23.3.1.1.71 | answerProfile-HdlcNrmAnswer-Enabled, answerProfile__hdlc_nrm_answer__enabled | 0 | 0 | Set to yes to enable incoming HDLC-NRM calls. |
| 1.3.6.1.4.1.529.23.3.1.1.72 | answerProfile-Visa2Answer-Enabled, answerProfile__visa2_answer__enabled | 0 | 0 | Set to yes to enable incoming VISA2 calls. |
| 1.3.6.1.4.1.529.23.3.1.1.73 | answerProfile-ClidSelection, answerProfile__clid_selection | 0 | 0 | Selection of the CLID. An incoming call can optionally specify several CLIDs. A CLID provided by the PSTN (network provided) is… |
| 1.3.6.1.4.1.529.23.3.1.1.74 | answerProfile-PppAnswer-IpxHeaderCompression, answerProfile__ppp_answer__ipx_header_compression | 0 | 0 | Use IPX header compression if encapsulation supports it. |
| 1.3.6.1.4.1.529.23.3.1.1.75 | answerProfile-PppAnswer-Mtu, answerProfile__ppp_answer__mtu | 0 | 0 | The Maximum Transmit Unit, i.e. the largest frame we will send out. |
| 1.3.6.1.4.1.529.23.3.1.1.76 | answerProfile-IpAnswer-PrivateRouteProfileRequired, answerProfile__ip_answer__private_route_profile_required | 0 | 0 | Parameter to decide default action,if private route table not found. If set to yes, the call will be cleared if the private rou… |
| 1.3.6.1.4.1.529.23.3.1.1.77 | answerProfile-SessionInfo-FilterRequired, answerProfile__session_info__filter_required | 0 | 0 | If No, the call will be allowed to come up even if the specified filter was not found either locally, in the cache or in RADIUS… |
| 1.3.6.1.4.1.529.23.3.1.1.78 | answerProfile-AtmAnswer-SvcEnabled, answerProfile__atm_answer__svc_enabled | 0 | 0 | Set to yes to enable ATM SVC athentication on incoming calls. |
| 1.3.6.1.4.1.529.23.3.1.1.79 | answerProfile-PppAnswer-BiDirectionalAuth, answerProfile__ppp_answer__bi_directional_auth | 0 | 0 | This parameter enables the authentication to be done in both directions. It can be used only with the CHAP, MS-CHAP or CACHE-TO… |
| 1.3.6.1.4.1.529.23.3.1.1.80 | answerProfile-PppAnswer-SubstituteSendName, answerProfile__ppp_answer__substitute_send_name | 0 | 0 | Name send to the far end, if different from the global system name. |
| 1.3.6.1.4.1.529.23.3.1.1.81 | answerProfile-PppAnswer-AuthForAsyncFramedUsers, answerProfile__ppp_answer__auth_for_async_framed_users | 0 | 0 | Determines whether we need to authenticate async framed users. |
| 1.3.6.1.4.1.529.23.3.1.1.82 | answerProfile-PppAnswer-MaxPapAuthRetry, answerProfile__ppp_answer__max_pap_auth_retry | 0 | 0 | Number of retries allowed, if PAP authentication fails. |
| 1.3.6.1.4.1.529.23.3.1.1.83 | answerProfile-IpAnswer-PoolForAsyncFramedUser, answerProfile__ip_answer__pool_for_async_framed_user | 0 | 0 | Pool number to be used for dial-in asynchronous PPP framed users with out authentication. |
| 1.3.6.1.4.1.529.23.3.1.1.85 | answerProfile-CallbackClidPrefix | 0 | 0 | Prefix to prepend to the dial number when callback is performed with the CLID number. |
| 1.3.6.1.4.1.529.23.3.1.1.87 | answerProfile-PriorityAnswer-PacketClassification | 0 | 0 | Method used to classify PPP packets. |
| 1.3.6.1.4.1.529.23.3.1.1.88 | answerProfile-PriorityAnswer-MaxRtpPacketDelay | 0 | 0 | Maximum delay for RTP packets in milli-seconds. Used for calculating the fragment size for the non-rtp traffic using the same l… |
| 1.3.6.1.4.1.529.23.3.1.1.89 | answerProfile-PriorityAnswer-MinimumRtpPort | 0 | 0 | Minimum UDP port for prioritization |
| 1.3.6.1.4.1.529.23.3.1.1.90 | answerProfile-PriorityAnswer-MaximumRtpPort | 0 | 0 | Maximum UDP port for prioritization |
| 1.3.6.1.4.1.529.23.3.1.1.91 | answerProfile-PriorityAnswer-NoHighPrioPktDuration | 0 | 0 | The number of seconds of no high priority packets before disabling IP fragmentation of low priority packets. The value 0 disabl… |
| 1.3.6.1.4.1.529.23.3.1.1.92 | answerProfile-PppAnswer-MaxPppConfigureRetry | 0 | 0 | Number of retries allowed, if LCP/NCP fails |
| 1.3.6.1.4.1.529.23.3.1.1.93 | answerProfile-PppAnswer-PppRestartTimer | 0 | 0 | Initial LCP/NCP restart timer |
| 1.3.6.1.4.1.529.23.3.1.1.94 | answerProfile-PppAnswer-MaxPppRestartTimer | 0 | 0 | Maximum LCP/NCP restart timer |
| 1.3.6.1.4.1.529.23.3.1.1.95 | answerProfile-PriorityAnswer-Enabled | 0 | 0 | Enable priority classification. |