This attribute displays whether a LOS (Loss of Signal) alarm state
is entered. An LOS alarm state is entered when LOS defects have
been observed and accumulated for a period of 2.5 seconds +/- 0.5
seconds. An LOS defect is declared at the JT2 line interface when
the input data is zero for 20 - 32 clock cycles. If the LOS defects are
intermittently occurring, the LOS defect accumulator is
decremented at a rate of 1/10 of the incrementing rate (alarm
integration ratio of 1/10), with all measurements based on a 200 ms
polling cycle.
An LOS failure alarm is cleared when the LOS defect is absent for a
period of 10 seconds +/- 0.5 seconds. The JT2 port goes into an
operationalState of disabled for the duration of the LOS alarm
condition. While the port is in the LOS alarm state, the port also
transmits the far-end RAI defect indicator on the out-going JT2 line.
Parsed from file nortelPP-logicalProcessorV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-LogicalProcessorMIB
This attribute displays whether a LOS (Loss of Signal) alarm state
is entered. An LOS alarm state is entered when LOS defects have
been observed and accumulated for a period of 2.5 seconds +/- 0.5
seconds. An LOS defect is declared at the JT2 line interface when
the input data is zero for 20 - 32 clock cycles. If the LOS defects are
intermittently occurring, the LOS defect accumulator is
decremented at a rate of 1/10 of the incrementing rate (alarm
integration ratio of 1/10), with all measurements based on a 200 ms
polling cycle.
An LOS failure alarm is cleared when the LOS defect is absent for a
period of 10 seconds +/- 0.5 seconds. The JT2 port goes into an
operationalState of disabled for the duration of the LOS alarm
condition. While the port is in the LOS alarm state, the port also
transmits the far-end RAI defect indicator on the out-going JT2 line.
Parsed from file Nortel-Magellan-Passport-LogicalProcessorMIB.mib
Module: Nortel-Magellan-Passport-LogicalProcessorMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-LogicalProcessorMIB
[Automatically extracted from oidview.com]
lpJT2LosAlarm OBJECT-TYPE SYNTAX INTEGER { on(0), off(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether a LOS (Loss of Signal) alarm state is entered. An LOS alarm state is entered when LOS defects have been observed and accumulated for a period of 2.5 seconds +/- 0.5 seconds. An LOS defect is declared at the JT2 line interface when the input data is zero for 20 - 32 clock cycles. If the LOS defects are intermittently occurring, the LOS defect accumulator is decremented at a rate of 1/10 of the incrementing rate (alarm integration ratio of 1/10), with all measurements based on a 200 ms polling cycle. An LOS failure alarm is cleared when the LOS defect is absent for a period of 10 seconds +/- 0.5 seconds. The JT2 port goes into an operationalState of disabled for the duration of the LOS alarm condition. While the port is in the LOS alarm state, the port also transmits the far-end RAI defect indicator on the out-going JT2 line." DEFVAL { off } ::= { lpJT2OperEntry 1 }
lpJT2LosAlarm OBJECT-TYPE SYNTAX INTEGER { on(0), off(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether a LOS (Loss of Signal) alarm state is entered. An LOS alarm state is entered when LOS defects have been observed and accumulated for a period of 2.5 seconds +/- 0.5 seconds. An LOS defect is declared at the JT2 line interface when the input data is zero for 20 - 32 clock cycles. If the LOS defects are intermittently occurring, the LOS defect accumulator is decremented at a rate of 1/10 of the incrementing rate (alarm integration ratio of 1/10), with all measurements based on a 200 ms polling cycle. An LOS failure alarm is cleared when the LOS defect is absent for a period of 10 seconds +/- 0.5 seconds. The JT2 port goes into an operationalState of disabled for the duration of the LOS alarm condition. While the port is in the LOS alarm state, the port also transmits the far-end RAI defect indicator on the out-going JT2 line." DEFVAL { off } ::= { lpJT2OperEntry 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.2.4.1.12.16.15.1.2 | lpJT2LofAlarm | 0 | 0 | This attribute indicates whether a LOF (Loss of Frame) alarm state is entered. A LOF alarm state is entered when LOF defects are… |
| 1.3.6.1.4.1.562.2.4.1.12.16.15.1.3 | lpJT2RxAisPhysicalAlarm | 0 | 0 | This attribute indicates whether a Physical AIS alarm state is entered. A Physical AIS alarm state is entered when a Physical AI… |
| 1.3.6.1.4.1.562.2.4.1.12.16.15.1.4 | lpJT2RxAisPayloadAlarm | 0 | 0 | This attribute indicates whether a Payload AIS alarm state is entered. A Payload AIS alarm state is entered when a Payload AIS de… |
| 1.3.6.1.4.1.562.2.4.1.12.16.15.1.5 | lpJT2RxRaiAlarm | 0 | 0 | This attribute indicates whether a Received RAI alarm state is entered. A received RAI alarm state is entered when the RAI signa… |
| 1.3.6.1.4.1.562.2.4.1.12.16.15.1.6 | lpJT2TxAisPhysicalAlarm | 0 | 0 | This attribute indicates whether an AIS (Alarm Indication Signal) alarm is being transmitted on the outgoing JT2 line. Currently… |
| 1.3.6.1.4.1.562.2.4.1.12.16.15.1.7 | lpJT2TxRaiAlarm | 0 | 0 | This attribute indicates whether an RAI defect indication pattern is being sent on the out-going JT2 line. The RAI alarm pattern… |