This attribute displays whether an Alarm Indication Signal (AIS)
alarm state has been entered. An AIS alarm state is entered when
AIS defects have been observed and accumulated for 2.5 seconds +/
- 0.5 seconds. An AIS defect is the occurrence of AIS (valid DS3
frame with payload containing the 1010...sequence and with C-Bits
set to zero) in contiguous M-frames for a time greater than 100
milliseconds. If the AIS defects are intermittently occurring, the
AIS defect accumulator is decremented at a rate of 1/10 of the
incrementing rate (alarm integration ratio of 1/10), with all
measurements based on a 200 ms polling cycle.
The DS3 component goes into an operational state of disabled until
the AIS alarm condition is cleared (after AIS has been no longer
detected for a period of 10 seconds +/- 0.5 seconds). As long as AIS
is detected, the node also transmits the far-end SEF/AIS defect
indicator over the outgoing line. When not running in C-Bit Parity
mode, the txRai attribute is also set to on when transmitting the far-
end SEF/AIS defect indicator on the outgoing line.
The rxAisAlarm attribute is always set to off when the component
has been locked and left offline.
Parsed from file nortelPP-logicalProcessorV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-LogicalProcessorMIB
This attribute displays whether an Alarm Indication Signal (AIS)
alarm state has been entered. An AIS alarm state is entered when
AIS defects have been observed and accumulated for 2.5 seconds +/
- 0.5 seconds. An AIS defect is the occurrence of AIS (valid DS3
frame with payload containing the 1010...sequence and with C-Bits
set to zero) in contiguous M-frames for a time greater than 100
milliseconds. If the AIS defects are intermittently occurring, the
AIS defect accumulator is decremented at a rate of 1/10 of the
incrementing rate (alarm integration ratio of 1/10), with all
measurements based on a 200 ms polling cycle.
The DS3 component goes into an operational state of disabled until
the AIS alarm condition is cleared (after AIS has been no longer
detected for a period of 10 seconds +/- 0.5 seconds). As long as AIS
is detected, the node also transmits the far-end SEF/AIS defect
indicator over the outgoing line. When not running in C-Bit Parity
mode, the txRai attribute is also set to on when transmitting the far-
end SEF/AIS defect indicator on the outgoing line.
The rxAisAlarm attribute is always set to off when the component
has been locked and left offline.
Parsed from file Nortel-Magellan-Passport-LogicalProcessorMIB.mib
Module: Nortel-Magellan-Passport-LogicalProcessorMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-LogicalProcessorMIB
[Automatically extracted from oidview.com]
lpDS3RxAisAlarm OBJECT-TYPE SYNTAX INTEGER { on(0), off(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether an Alarm Indication Signal (AIS) alarm state has been entered. An AIS alarm state is entered when AIS defects have been observed and accumulated for 2.5 seconds +/ - 0.5 seconds. An AIS defect is the occurrence of AIS (valid DS3 frame with payload containing the 1010...sequence and with C-Bits set to zero) in contiguous M-frames for a time greater than 100 milliseconds. If the AIS defects are intermittently occurring, the AIS defect accumulator is decremented at a rate of 1/10 of the incrementing rate (alarm integration ratio of 1/10), with all measurements based on a 200 ms polling cycle. The DS3 component goes into an operational state of disabled until the AIS alarm condition is cleared (after AIS has been no longer detected for a period of 10 seconds +/- 0.5 seconds). As long as AIS is detected, the node also transmits the far-end SEF/AIS defect indicator over the outgoing line. When not running in C-Bit Parity mode, the txRai attribute is also set to on when transmitting the far- end SEF/AIS defect indicator on the outgoing line. The rxAisAlarm attribute is always set to off when the component has been locked and left offline." DEFVAL { off } ::= { lpDS3OperEntry 3 }
lpDS3RxAisAlarm OBJECT-TYPE SYNTAX INTEGER { on(0), off(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether an Alarm Indication Signal (AIS) alarm state has been entered. An AIS alarm state is entered when AIS defects have been observed and accumulated for 2.5 seconds +/ - 0.5 seconds. An AIS defect is the occurrence of AIS (valid DS3 frame with payload containing the 1010...sequence and with C-Bits set to zero) in contiguous M-frames for a time greater than 100 milliseconds. If the AIS defects are intermittently occurring, the AIS defect accumulator is decremented at a rate of 1/10 of the incrementing rate (alarm integration ratio of 1/10), with all measurements based on a 200 ms polling cycle. The DS3 component goes into an operational state of disabled until the AIS alarm condition is cleared (after AIS has been no longer detected for a period of 10 seconds +/- 0.5 seconds). As long as AIS is detected, the node also transmits the far-end SEF/AIS defect indicator over the outgoing line. When not running in C-Bit Parity mode, the txRai attribute is also set to on when transmitting the far- end SEF/AIS defect indicator on the outgoing line. The rxAisAlarm attribute is always set to off when the component has been locked and left offline." DEFVAL { off } ::= { lpDS3OperEntry 3 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.2.4.1.12.5.16.1.1 | lpDS3LosAlarm | 0 | 0 | This attribute displays whether a Loss Of Signal (LOS) alarm state has been entered. An LOS alarm state is entered when LOS defe… |
| 1.3.6.1.4.1.562.2.4.1.12.5.16.1.2 | lpDS3LofAlarm | 0 | 0 | This attribute displays whether a Loss Of Frame (LOF) alarm state has been entered. An LOF alarm state is entered when Severely E… |
| 1.3.6.1.4.1.562.2.4.1.12.5.16.1.4 | lpDS3RxRaiAlarm | 0 | 0 | This attribute displays whether a Remote Alarm Indication (RAI) alarm state has been entered. When not running the C-Bit Parity m… |
| 1.3.6.1.4.1.562.2.4.1.12.5.16.1.5 | lpDS3RxIdle | 0 | 0 | This attribute displays whether an Idle failure condition has been reported on the DS3 port. An Idle condition is reported when … |
| 1.3.6.1.4.1.562.2.4.1.12.5.16.1.6 | lpDS3TxAis | 0 | 0 | This attribute displays whether an Alarm Indication Signal (AIS) alarm is being transmitted on the DS3 line. Currently, AIS is n… |
| 1.3.6.1.4.1.562.2.4.1.12.5.16.1.7 | lpDS3TxRai | 0 | 0 | When not running C-Bit Parity mode, this attribute displays whether the far-end SEF/AIS defect indicator is transmitted over the… |
| 1.3.6.1.4.1.562.2.4.1.12.5.16.1.8 | lpDS3TxIdle | 0 | 0 | This attribute displays whether the DS3 Idle signal is transmitted over the outgoing line. DS3 Idle is sent when the DS3 compone… |