This attribute displays whether an Idle failure condition has been
reported on the DS3 port. An Idle condition is reported when DS3
Idle defects have been observed and accumulated for a period of 2.5
seconds +/- 0.5 seconds. The DS3 Idle defect is the occurrence of a
valid DS3 frame with the information bits set to a 11001100..
sequence. If the DS3 Idle defects are intermittently occurring, the
DS3 Idle defect accumulator is decremented at a rate of 1/10 of the
incrementing rate (alarm integration ratio of 1/10), with all
measurements based on a 200 ms polling cycle.
The DS3 component goes into an operational state of disabled until
the Idle failure condition is cleared. The failure condition is cleared
when the DS3 idle pattern has not been detected for at least 10
seconds +/- 0.5 seconds.
The rxIdle attribute is always set to off when the component has
been locked and left offline.
The idle pattern indicates that the far-end is physically connected
but not put in service. For instance, DS3 idle is transmitted on the
outgoing line when the DS3 component is locked and not used for
operational testing.
Parsed from file nortelPP-logicalProcessorV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-LogicalProcessorMIB
This attribute displays whether an Idle failure condition has been
reported on the DS3 port. An Idle condition is reported when DS3
Idle defects have been observed and accumulated for a period of 2.5
seconds +/- 0.5 seconds. The DS3 Idle defect is the occurrence of a
valid DS3 frame with the information bits set to a 11001100..
sequence. If the DS3 Idle defects are intermittently occurring, the
DS3 Idle defect accumulator is decremented at a rate of 1/10 of the
incrementing rate (alarm integration ratio of 1/10), with all
measurements based on a 200 ms polling cycle.
The DS3 component goes into an operational state of disabled until
the Idle failure condition is cleared. The failure condition is cleared
when the DS3 idle pattern has not been detected for at least 10
seconds +/- 0.5 seconds.
The rxIdle attribute is always set to off when the component has
been locked and left offline.
The idle pattern indicates that the far-end is physically connected
but not put in service. For instance, DS3 idle is transmitted on the
outgoing line when the DS3 component is locked and not used for
operational testing.
Parsed from file Nortel-Magellan-Passport-LogicalProcessorMIB.mib
Module: Nortel-Magellan-Passport-LogicalProcessorMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-LogicalProcessorMIB
[Automatically extracted from oidview.com]
lpDS3RxIdle OBJECT-TYPE SYNTAX INTEGER { on(0), off(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether an Idle failure condition has been reported on the DS3 port. An Idle condition is reported when DS3 Idle defects have been observed and accumulated for a period of 2.5 seconds +/- 0.5 seconds. The DS3 Idle defect is the occurrence of a valid DS3 frame with the information bits set to a 11001100.. sequence. If the DS3 Idle defects are intermittently occurring, the DS3 Idle defect accumulator is decremented at a rate of 1/10 of the incrementing rate (alarm integration ratio of 1/10), with all measurements based on a 200 ms polling cycle. The DS3 component goes into an operational state of disabled until the Idle failure condition is cleared. The failure condition is cleared when the DS3 idle pattern has not been detected for at least 10 seconds +/- 0.5 seconds. The rxIdle attribute is always set to off when the component has been locked and left offline. The idle pattern indicates that the far-end is physically connected but not put in service. For instance, DS3 idle is transmitted on the outgoing line when the DS3 component is locked and not used for operational testing." DEFVAL { off } ::= { lpDS3OperEntry 5 }
lpDS3RxIdle OBJECT-TYPE SYNTAX INTEGER { on(0), off(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether an Idle failure condition has been reported on the DS3 port. An Idle condition is reported when DS3 Idle defects have been observed and accumulated for a period of 2.5 seconds +/- 0.5 seconds. The DS3 Idle defect is the occurrence of a valid DS3 frame with the information bits set to a 11001100.. sequence. If the DS3 Idle defects are intermittently occurring, the DS3 Idle defect accumulator is decremented at a rate of 1/10 of the incrementing rate (alarm integration ratio of 1/10), with all measurements based on a 200 ms polling cycle. The DS3 component goes into an operational state of disabled until the Idle failure condition is cleared. The failure condition is cleared when the DS3 idle pattern has not been detected for at least 10 seconds +/- 0.5 seconds. The rxIdle attribute is always set to off when the component has been locked and left offline. The idle pattern indicates that the far-end is physically connected but not put in service. For instance, DS3 idle is transmitted on the outgoing line when the DS3 component is locked and not used for operational testing." DEFVAL { off } ::= { lpDS3OperEntry 5 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.2.4.1.12.5.16.1.1 | lpDS3LosAlarm | 0 | 0 | This attribute displays whether a Loss Of Signal (LOS) alarm state has been entered. An LOS alarm state is entered when LOS defe… |
| 1.3.6.1.4.1.562.2.4.1.12.5.16.1.2 | lpDS3LofAlarm | 0 | 0 | This attribute displays whether a Loss Of Frame (LOF) alarm state has been entered. An LOF alarm state is entered when Severely E… |
| 1.3.6.1.4.1.562.2.4.1.12.5.16.1.3 | lpDS3RxAisAlarm | 0 | 0 | This attribute displays whether an Alarm Indication Signal (AIS) alarm state has been entered. An AIS alarm state is entered whe… |
| 1.3.6.1.4.1.562.2.4.1.12.5.16.1.4 | lpDS3RxRaiAlarm | 0 | 0 | This attribute displays whether a Remote Alarm Indication (RAI) alarm state has been entered. When not running the C-Bit Parity m… |
| 1.3.6.1.4.1.562.2.4.1.12.5.16.1.6 | lpDS3TxAis | 0 | 0 | This attribute displays whether an Alarm Indication Signal (AIS) alarm is being transmitted on the DS3 line. Currently, AIS is n… |
| 1.3.6.1.4.1.562.2.4.1.12.5.16.1.7 | lpDS3TxRai | 0 | 0 | When not running C-Bit Parity mode, this attribute displays whether the far-end SEF/AIS defect indicator is transmitted over the… |
| 1.3.6.1.4.1.562.2.4.1.12.5.16.1.8 | lpDS3TxIdle | 0 | 0 | This attribute displays whether the DS3 Idle signal is transmitted over the outgoing line. DS3 Idle is sent when the DS3 compone… |