This attribute specifies how ingress voice traffic is encoded.
If voiceEncoding is g711G726, ingress voice traffic is encoded
using either pulse code modulation (PCM) defined by ITU-T G.711
or adaptive differential pulse code modulation (ADPCM) defined by
ITU-T G.726. The actual encoding and rates performed depends on
congestion in the network and the minimum and maximum
negotiated ingress voice rates in negotiatedIgRates.
If voiceEncoding is g728at16, ingress voice traffic is encoded using
the Low Delay Coded Excited Linear Predictive Coder (LD-CELP)
algorithm defined by ITU-T G.728. If voiceEncoding is g728at16,
the bit rate of all voice traffic is fixed at 16 kbit/s.
minVoiceG711G726Rate and maxVoiceG711G726Rate do not apply
if voiceEncoding is g728at16.
If voiceEncoding is g729at8, ingress voice traffic is encoded using
the Conjugated Structure Algebraic Code Excited Linear Predictive
Coder (CS-ACELP) algorithm defined by ITU-T G.729. If
voiceEncoding is g729at8, the bit rate of all voice traffic is fixed at
8 kbit/s. minVoiceG711G726Rate and maxVoiceG711G726Rate do
not apply if voiceEncoding is g729at8.
The current ingress encoding and encoding rate are available in
currentEncoding and currentRate.
voiceEncoding cannot be set to g728at16 or g729at8 if this
VoiceService is running on a DS1V, E1V, 1pDS1V, 1pE1V or J2MV
card. Also, voiceEncoding can only be set to g728at16 or g729at8 if
the corresponding feature exists in the featureList of the Sw Lpt.
The negotiated ingress voice encoding is available in
negotiatedIgEncoding.
voiceEncoding must have the same value at both ends of a
VoiceService. If voiceEncoding does not have the same value at
both ends of a VoiceService, the VoiceService will be out of service.
In this case, serviceFailureReason is mismatchedVoiceEncoding.
Parsed from file nortelPP-voiceV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-VoiceMIB
This attribute specifies how ingress voice traffic is encoded.
If voiceEncoding is g711G726, ingress voice traffic is encoded
using either pulse code modulation (PCM) defined by ITU-T G.711
or adaptive differential pulse code modulation (ADPCM) defined by
ITU-T G.726. The actual encoding and rates performed depends on
congestion in the network and the minimum and maximum
negotiated ingress voice rates in negotiatedIgRates.
If voiceEncoding is g728at16, ingress voice traffic is encoded using
the Low Delay Coded Excited Linear Predictive Coder (LD-CELP)
algorithm defined by ITU-T G.728. If voiceEncoding is g728at16,
the bit rate of all voice traffic is fixed at 16 kbit/s.
minVoiceG711G726Rate and maxVoiceG711G726Rate do not apply
if voiceEncoding is g728at16.
If voiceEncoding is g729at8, ingress voice traffic is encoded using
the Conjugated Structure Algebraic Code Excited Linear Predictive
Coder (CS-ACELP) algorithm defined by ITU-T G.729. If
voiceEncoding is g729at8, the bit rate of all voice traffic is fixed at
8 kbit/s. minVoiceG711G726Rate and maxVoiceG711G726Rate do
not apply if voiceEncoding is g729at8.
The current ingress encoding and encoding rate are available in
currentEncoding and currentRate.
voiceEncoding cannot be set to g728at16 or g729at8 if this
VoiceService is running on a DS1V, E1V, 1pDS1V, 1pE1V or J2MV
card. Also, voiceEncoding can only be set to g728at16 or g729at8 if
the corresponding feature exists in the featureList of the Sw Lpt.
The negotiated ingress voice encoding is available in
negotiatedIgEncoding.
voiceEncoding must have the same value at both ends of a
VoiceService. If voiceEncoding does not have the same value at
both ends of a VoiceService, the VoiceService will be out of service.
In this case, serviceFailureReason is mismatchedVoiceEncoding.
Parsed from file Nortel-Magellan-Passport-VoiceMIB.mib
Module: Nortel-Magellan-Passport-VoiceMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-VoiceMIB
[Automatically extracted from oidview.com]
vsFramerVoiceEncoding OBJECT-TYPE SYNTAX INTEGER { g711G726(0), g728at16(1), g729at8(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies how ingress voice traffic is encoded. If voiceEncoding is g711G726, ingress voice traffic is encoded using either pulse code modulation (PCM) defined by ITU-T G.711 or adaptive differential pulse code modulation (ADPCM) defined by ITU-T G.726. The actual encoding and rates performed depends on congestion in the network and the minimum and maximum negotiated ingress voice rates in negotiatedIgRates. If voiceEncoding is g728at16, ingress voice traffic is encoded using the Low Delay Coded Excited Linear Predictive Coder (LD-CELP) algorithm defined by ITU-T G.728. If voiceEncoding is g728at16, the bit rate of all voice traffic is fixed at 16 kbit/s. minVoiceG711G726Rate and maxVoiceG711G726Rate do not apply if voiceEncoding is g728at16. If voiceEncoding is g729at8, ingress voice traffic is encoded using the Conjugated Structure Algebraic Code Excited Linear Predictive Coder (CS-ACELP) algorithm defined by ITU-T G.729. If voiceEncoding is g729at8, the bit rate of all voice traffic is fixed at 8 kbit/s. minVoiceG711G726Rate and maxVoiceG711G726Rate do not apply if voiceEncoding is g729at8. The current ingress encoding and encoding rate are available in currentEncoding and currentRate. voiceEncoding cannot be set to g728at16 or g729at8 if this VoiceService is running on a DS1V, E1V, 1pDS1V, 1pE1V or J2MV card. Also, voiceEncoding can only be set to g728at16 or g729at8 if the corresponding feature exists in the featureList of the Sw Lpt. The negotiated ingress voice encoding is available in negotiatedIgEncoding. voiceEncoding must have the same value at both ends of a VoiceService. If voiceEncoding does not have the same value at both ends of a VoiceService, the VoiceService will be out of service. In this case, serviceFailureReason is mismatchedVoiceEncoding." DEFVAL { g711G726 } ::= { vsFramerCoderEntry 11 }
vsFramerVoiceEncoding OBJECT-TYPE SYNTAX INTEGER { g711G726(0), g728at16(1), g729at8(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies how ingress voice traffic is encoded. If voiceEncoding is g711G726, ingress voice traffic is encoded using either pulse code modulation (PCM) defined by ITU-T G.711 or adaptive differential pulse code modulation (ADPCM) defined by ITU-T G.726. The actual encoding and rates performed depends on congestion in the network and the minimum and maximum negotiated ingress voice rates in negotiatedIgRates. If voiceEncoding is g728at16, ingress voice traffic is encoded using the Low Delay Coded Excited Linear Predictive Coder (LD-CELP) algorithm defined by ITU-T G.728. If voiceEncoding is g728at16, the bit rate of all voice traffic is fixed at 16 kbit/s. minVoiceG711G726Rate and maxVoiceG711G726Rate do not apply if voiceEncoding is g728at16. If voiceEncoding is g729at8, ingress voice traffic is encoded using the Conjugated Structure Algebraic Code Excited Linear Predictive Coder (CS-ACELP) algorithm defined by ITU-T G.729. If voiceEncoding is g729at8, the bit rate of all voice traffic is fixed at 8 kbit/s. minVoiceG711G726Rate and maxVoiceG711G726Rate do not apply if voiceEncoding is g729at8. The current ingress encoding and encoding rate are available in currentEncoding and currentRate. voiceEncoding cannot be set to g728at16 or g729at8 if this VoiceService is running on a DS1V, E1V, 1pDS1V, 1pE1V or J2MV card. Also, voiceEncoding can only be set to g728at16 or g729at8 if the corresponding feature exists in the featureList of the Sw Lpt. The negotiated ingress voice encoding is available in negotiatedIgEncoding. voiceEncoding must have the same value at both ends of a VoiceService. If voiceEncoding does not have the same value at both ends of a VoiceService, the VoiceService will be out of service. In this case, serviceFailureReason is mismatchedVoiceEncoding." DEFVAL { g711G726 } ::= { vsFramerCoderEntry 11 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.562.2.4.1.80.2.12.1.1 | vsFramerMaxVoiceBitRate | 0 | 0 | This attribute specifies the maximum desired ingress bit rate used during voice traffic when voiceEncoding is g711G726. The nego… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.2 | vsFramerMinVoiceBitRate | 0 | 0 | This attribute specifies the minimum desired ingress bit rate used during voice traffic when voiceEncoding is g711G726. The nego… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.3 | vsFramerMaxModemBitRate | 0 | 0 | This attribute specifies the maximum desired ingress rate used during modemFax and/or fax traffic. Voice traffic is all traffic … |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.4 | vsFramerMinModemBitRate | 0 | 0 | This attribute specifies the minimum desired ingress rate used during modemFax and/or fax traffic. Voice traffic is all traffic … |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.5 | vsFramerAudioGain | 0 | 0 | This attribute has been migrated to egressAudioGain. |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.6 | vsFramerSilenceSuppression | 0 | 0 | This attribute specifies when ingress silence suppression is desired during voice traffic. If silenceSuppression is off, silence… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.7 | vsFramerEchoCancellation | 0 | 0 | This attribute specifies whether echo cancellation is performed on this VoiceService. If echoCancellation is on, the internal ec… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.9 | vsFramerALawConversion | 0 | 0 | This attribute specifies whether mu-law to A-law PCM conversion is performed. aLawConversion only needs to be set to on when thi… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.12 | vsFramerFaxEncoding | 0 | 0 | This attribute specifies how ingress modemFax and fax traffic are encoded. Voice traffic is all traffic from the start of a call… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.13 | vsFramerTandemPassThrough | 0 | 0 | This attribute specifies whether tandem pass through is desired. If tandemPassThrough is enabled, tandem pass through is used if… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.14 | vsFramerInsertedOutputDelay | 0 | 0 | This attribute specifies the amount of added output delay used to compensate for cross network delay variations. It applies to v… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.15 | vsFramerEgressAudioGain | 0 | 0 | This attribute has been migrated to ingressAudioGain. |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.16 | vsFramerFaxIdleSuppressionG711G726 | 0 | 0 | This attribute specifies whether ingress fax idle suppression is desired during G.711 and G.726 fax traffic. It applies only if m… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.17 | vsFramerEndOfCallPattern | 0 | 0 | This attribute specifies the pattern that indicates the end of a CCS call. The pattern is specified as a hexadecimal byte. If th… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.18 | vsFramerIngressAudioGain | 0 | 0 | This attribute specifies the gain in dB that is applied to data coming from outside the network before it is transferred across … |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.19 | vsFramerEgressGain | 0 | 0 | This attribute specifies the gain in dB that is applied to data before it leaves the network. It applies to voice, modem and fax… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.20 | vsFramerComfortNoiseCap | 0 | 0 | This attribute specifies the maximum level at which comfort noise is generated. The comfort noise is limited by comfortNoiseCap … |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.21 | vsFramerEchoTailDelay | 0 | 0 | This attribute specifies the maximum echo canceller tail delay coverage. It should be selected higher than the summation of the r… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.22 | vsFramerEchoReturnLoss | 0 | 0 | This attribute specifies the echo return loss parameter of the echo canceller. 0 db is the normal value for most line conditions… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.34 | vsFramerDtmfRegeneration | 0 | 0 | This attribute specifies the DTMF regeneration parameter used during negotiation with the remote end across the subnet. If dtmfR… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.35 | vsFramerSpeechHangoverTime | 0 | 0 | This attribute specifies the time after the end of speech before silence suppression starts. It applies only to voice traffic. I… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.36 | vsFramerFaxHangoverTimeG711G726 | 0 | 0 | This attribute specifies the time after the end of fax traffic before ingress G.711/G.726 fax idle suppression starts. It applie… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.37 | vsFramerModemFaxSpeechDiscrim | 0 | 0 | This attribute specifies whether this VoiceService differentiates modemFax traffic and speech. If modemFaxSpeechDiscrim is on and… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.39 | vsFramerV17EncodedAsG711G726 | 0 | 0 | This attribute specifies the desired negotiation between this VoiceService and V.17 fax machines when modemFaxEncoding is faxRela… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.40 | vsFramerEcanBypassMode | 0 | 0 | This attribute specifies when version 2 internal echo cancellers are placed in bypass mode on this VoiceService. This attribute… |
1.3.6.1.4.1.562.2.4.1.80.2.12.1.41 | vsFramerMaxFaxRelayRate | 0 | 0 | This attribute specifies the maximum desired fax relay rate. This attribute only applies if modemFaxEncoding is faxRelayOnly or f… |