This attribute displays whether a Loss Of Signal (LOS) alarm state
has been entered. An LOS alarm state is entered when LOS defects
have been observed and accumulated for a period of 2.5 seconds +/-
0.5 seconds. An LOS defect is detected at the DS3 line interface
upon observing 175 +/- 75 continuous pulse positions with no
pulses of either positive or negative polarity. If the LOS defects are
intermittently occurring, the LOS defect accumulator is
decremented at a rate of 1/10 of the incrementing rate (alarm
integration ratio of 1/10), with all measurements based on a 200 ms
polling cycle.
The DS3 component goes into an operational state of disabled until
the LOS alarm condition is cleared. The LOS alarm state is cleared
after LOS defects have been absent for a period of 10 seconds +/-
0.5 seconds.
The losAlarm attribute is always set to off when the component has
been locked and left offline.
Parsed from file nortelPC-logicalProcessorV1.mib.txt
Company: None
Module: Nortel-MsCarrier-MscPassport-LogicalProcessorMIB
This attribute displays whether a Loss Of Signal (LOS) alarm state
has been entered. An LOS alarm state is entered when LOS defects
have been observed and accumulated for a period of 2.5 seconds +/-
0.5 seconds. An LOS defect is detected at the DS3 line interface
upon observing 175 +/- 75 continuous pulse positions with no
pulses of either positive or negative polarity. If the LOS defects are
intermittently occurring, the LOS defect accumulator is
decremented at a rate of 1/10 of the incrementing rate (alarm
integration ratio of 1/10), with all measurements based on a 200 ms
polling cycle.
The DS3 component goes into an operational state of disabled until
the LOS alarm condition is cleared. The LOS alarm state is cleared
after LOS defects have been absent for a period of 10 seconds +/-
0.5 seconds.
The losAlarm attribute is always set to off when the component has
been locked and left offline.
Parsed from file Nortel-MsCarrier-MscPassport-LogicalProcessorMIB.mib
Module: Nortel-MsCarrier-MscPassport-LogicalProcessorMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-MsCarrier-MscPassport-LogicalProcessorMIB
[Automatically extracted from oidview.com]
mscLpDS3LosAlarm OBJECT-TYPE SYNTAX INTEGER { on(0), off(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether a Loss Of Signal (LOS) alarm state has been entered. An LOS alarm state is entered when LOS defects have been observed and accumulated for a period of 2.5 seconds +/- 0.5 seconds. An LOS defect is detected at the DS3 line interface upon observing 175 +/- 75 continuous pulse positions with no pulses of either positive or negative polarity. If the LOS defects are intermittently occurring, the LOS defect accumulator is decremented at a rate of 1/10 of the incrementing rate (alarm integration ratio of 1/10), with all measurements based on a 200 ms polling cycle. The DS3 component goes into an operational state of disabled until the LOS alarm condition is cleared. The LOS alarm state is cleared after LOS defects have been absent for a period of 10 seconds +/- 0.5 seconds. The losAlarm attribute is always set to off when the component has been locked and left offline." DEFVAL { off } ::= { mscLpDS3OperEntry 1 }
mscLpDS3LosAlarm OBJECT-TYPE SYNTAX INTEGER { on(0), off(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether a Loss Of Signal (LOS) alarm state has been entered. An LOS alarm state is entered when LOS defects have been observed and accumulated for a period of 2.5 seconds +/- 0.5 seconds. An LOS defect is detected at the DS3 line interface upon observing 175 +/- 75 continuous pulse positions with no pulses of either positive or negative polarity. If the LOS defects are intermittently occurring, the LOS defect accumulator is decremented at a rate of 1/10 of the incrementing rate (alarm integration ratio of 1/10), with all measurements based on a 200 ms polling cycle. The DS3 component goes into an operational state of disabled until the LOS alarm condition is cleared. The LOS alarm state is cleared after LOS defects have been absent for a period of 10 seconds +/- 0.5 seconds. The losAlarm attribute is always set to off when the component has been locked and left offline." DEFVAL { off } ::= { mscLpDS3OperEntry 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.36.2.1.12.5.16.1.2 | mscLpDS3LofAlarm | 0 | 0 | This attribute displays whether a Loss Of Frame (LOF) alarm state has been entered. An LOF alarm state is entered when Severely E… |
| 1.3.6.1.4.1.562.36.2.1.12.5.16.1.3 | mscLpDS3RxAisAlarm | 0 | 0 | This attribute displays whether an Alarm Indication Signal (AIS) alarm state has been entered. An AIS alarm state is entered whe… |
| 1.3.6.1.4.1.562.36.2.1.12.5.16.1.4 | mscLpDS3RxRaiAlarm | 0 | 0 | This attribute displays whether a Remote Alarm Indication (RAI) alarm state has been entered. When not running the C-Bit Parity m… |
| 1.3.6.1.4.1.562.36.2.1.12.5.16.1.5 | mscLpDS3RxIdle | 0 | 0 | This attribute displays whether an Idle failure condition has been reported on the DS3 port. An Idle condition is reported when … |
| 1.3.6.1.4.1.562.36.2.1.12.5.16.1.6 | mscLpDS3TxAis | 0 | 0 | This attribute displays whether an Alarm Indication Signal (AIS) alarm is being transmitted on the DS3 line. Currently, AIS is n… |
| 1.3.6.1.4.1.562.36.2.1.12.5.16.1.7 | mscLpDS3TxRai | 0 | 0 | When not running C-Bit Parity mode, this attribute displays whether the far-end SEF/AIS defect indicator is transmitted over the… |
| 1.3.6.1.4.1.562.36.2.1.12.5.16.1.8 | mscLpDS3TxIdle | 0 | 0 | This attribute displays whether the DS3 Idle signal is transmitted over the outgoing line. DS3 Idle is sent when the DS3 compone… |