This attribute displays whether a Loss Of Frame (LOF) alarm state
has been entered. An LOF alarm state is entered when Severely
Errored Frame (SEF) defects have been observed and accumulated
for a period of 2.5 seconds +/- 0.5 seconds. A SEF defect is
detected when 3 (or more) out of 16 (or fewer) F-bits are in error, or
one (or more) M-bits in two (or more) out of four (or fewer)
consecutive M-frames are in error. If the LOF defects are
intermittently occurring, the LOF defect accumulator is
decremented at a rate of 1/10 of the incrementing rate (alarm
integration ratio of 1/10), with all measurements based on a 200 ms
polling cycle.
The DS3 component goes into an operational state of disabled until
the LOF alarm condition is cleared. The condition is cleared when
framing has been achieved for a period of 10 seconds +/- 0.5
seconds. As long as SEF defects are detected, the node also
transmits the far-end SEF/AIS defect indicator over the outgoing
line. When not running in C-Bit Parity mode, the txRai attribute is
also set to on when transmitting the far-end SEF/AIS defect
indicator on the outgoing line.
The lofAlarm attribute is always set to off when the component has
been locked and left offline.
Parsed from file nortelPC-logicalProcessorV1.mib.txt
Company: None
Module: Nortel-MsCarrier-MscPassport-LogicalProcessorMIB
This attribute displays whether a Loss Of Frame (LOF) alarm state
has been entered. An LOF alarm state is entered when Severely
Errored Frame (SEF) defects have been observed and accumulated
for a period of 2.5 seconds +/- 0.5 seconds. A SEF defect is
detected when 3 (or more) out of 16 (or fewer) F-bits are in error, or
one (or more) M-bits in two (or more) out of four (or fewer)
consecutive M-frames are in error. If the LOF defects are
intermittently occurring, the LOF defect accumulator is
decremented at a rate of 1/10 of the incrementing rate (alarm
integration ratio of 1/10), with all measurements based on a 200 ms
polling cycle.
The DS3 component goes into an operational state of disabled until
the LOF alarm condition is cleared. The condition is cleared when
framing has been achieved for a period of 10 seconds +/- 0.5
seconds. As long as SEF defects are detected, the node also
transmits the far-end SEF/AIS defect indicator over the outgoing
line. When not running in C-Bit Parity mode, the txRai attribute is
also set to on when transmitting the far-end SEF/AIS defect
indicator on the outgoing line.
The lofAlarm attribute is always set to off when the component has
been locked and left offline.
Parsed from file Nortel-MsCarrier-MscPassport-LogicalProcessorMIB.mib
Module: Nortel-MsCarrier-MscPassport-LogicalProcessorMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-MsCarrier-MscPassport-LogicalProcessorMIB
[Automatically extracted from oidview.com]
mscLpDS3LofAlarm OBJECT-TYPE SYNTAX INTEGER { on(0), off(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether a Loss Of Frame (LOF) alarm state has been entered. An LOF alarm state is entered when Severely Errored Frame (SEF) defects have been observed and accumulated for a period of 2.5 seconds +/- 0.5 seconds. A SEF defect is detected when 3 (or more) out of 16 (or fewer) F-bits are in error, or one (or more) M-bits in two (or more) out of four (or fewer) consecutive M-frames are in error. If the LOF defects are intermittently occurring, the LOF defect accumulator is decremented at a rate of 1/10 of the incrementing rate (alarm integration ratio of 1/10), with all measurements based on a 200 ms polling cycle. The DS3 component goes into an operational state of disabled until the LOF alarm condition is cleared. The condition is cleared when framing has been achieved for a period of 10 seconds +/- 0.5 seconds. As long as SEF defects are detected, the node also transmits the far-end SEF/AIS defect indicator over the outgoing line. When not running in C-Bit Parity mode, the txRai attribute is also set to on when transmitting the far-end SEF/AIS defect indicator on the outgoing line. The lofAlarm attribute is always set to off when the component has been locked and left offline." DEFVAL { off } ::= { mscLpDS3OperEntry 2 }
mscLpDS3LofAlarm OBJECT-TYPE SYNTAX INTEGER { on(0), off(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute displays whether a Loss Of Frame (LOF) alarm state has been entered. An LOF alarm state is entered when Severely Errored Frame (SEF) defects have been observed and accumulated for a period of 2.5 seconds +/- 0.5 seconds. A SEF defect is detected when 3 (or more) out of 16 (or fewer) F-bits are in error, or one (or more) M-bits in two (or more) out of four (or fewer) consecutive M-frames are in error. If the LOF defects are intermittently occurring, the LOF defect accumulator is decremented at a rate of 1/10 of the incrementing rate (alarm integration ratio of 1/10), with all measurements based on a 200 ms polling cycle. The DS3 component goes into an operational state of disabled until the LOF alarm condition is cleared. The condition is cleared when framing has been achieved for a period of 10 seconds +/- 0.5 seconds. As long as SEF defects are detected, the node also transmits the far-end SEF/AIS defect indicator over the outgoing line. When not running in C-Bit Parity mode, the txRai attribute is also set to on when transmitting the far-end SEF/AIS defect indicator on the outgoing line. The lofAlarm attribute is always set to off when the component has been locked and left offline." DEFVAL { off } ::= { mscLpDS3OperEntry 2 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.36.2.1.12.5.16.1.1 | mscLpDS3LosAlarm | 0 | 0 | This attribute displays whether a Loss Of Signal (LOS) alarm state has been entered. An LOS alarm state is entered when LOS defe… |
| 1.3.6.1.4.1.562.36.2.1.12.5.16.1.3 | mscLpDS3RxAisAlarm | 0 | 0 | This attribute displays whether an Alarm Indication Signal (AIS) alarm state has been entered. An AIS alarm state is entered whe… |
| 1.3.6.1.4.1.562.36.2.1.12.5.16.1.4 | mscLpDS3RxRaiAlarm | 0 | 0 | This attribute displays whether a Remote Alarm Indication (RAI) alarm state has been entered. When not running the C-Bit Parity m… |
| 1.3.6.1.4.1.562.36.2.1.12.5.16.1.5 | mscLpDS3RxIdle | 0 | 0 | This attribute displays whether an Idle failure condition has been reported on the DS3 port. An Idle condition is reported when … |
| 1.3.6.1.4.1.562.36.2.1.12.5.16.1.6 | mscLpDS3TxAis | 0 | 0 | This attribute displays whether an Alarm Indication Signal (AIS) alarm is being transmitted on the DS3 line. Currently, AIS is n… |
| 1.3.6.1.4.1.562.36.2.1.12.5.16.1.7 | mscLpDS3TxRai | 0 | 0 | When not running C-Bit Parity mode, this attribute displays whether the far-end SEF/AIS defect indicator is transmitted over the… |
| 1.3.6.1.4.1.562.36.2.1.12.5.16.1.8 | mscLpDS3TxIdle | 0 | 0 | This attribute displays whether the DS3 Idle signal is transmitted over the outgoing line. DS3 Idle is sent when the DS3 compone… |