This attribute sets the time until an Access-Point discontinues
sending beacons to the Wireless LAN when no multicast or unicast
frames for the cell arrive from the Ethernet.
This option is available ONLY on AP (na value assigned in
non-AP devices).
Parsed from file BREEZECOM-MIB.mib
Module: BREEZECOM-MIB
Vendor: Lannair Ltd.
Module: BREEZECOM-MIB
[Automatically extracted from oidview.com]
brzApRedundancyLimit OBJECT-TYPE SYNTAX INTEGER {na(255)} ACCESS read-write STATUS mandatory DESCRIPTION "This attribute sets the time until an Access-Point discontinues sending beacons to the Wireless LAN when no multicast or unicast frames for the cell arrive from the Ethernet. This option is available ONLY on AP (na value assigned in non-AP devices)." ::= { sysParams 13 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.710.3.2.1.2.1 | brzHWMacAddress | 0 | 0 | The Hardware MAC address of the device. |
1.3.6.1.4.1.710.3.2.1.2.2 | brzApplTunneling | 0 | 0 | This attribute specifies the device tunneling mode, as follows: ipx - The device will enable IPX tunneling only. apple-ta… |
1.3.6.1.4.1.710.3.2.1.2.3 | brzPositiveBrg | 0 | 0 | This attribute specifies the Wired to Wireless LAN bridging mode at the AP, as follows: reject-unknown - The AP forwards to the … |
1.3.6.1.4.1.710.3.2.1.2.4 | brzIpFilter | 0 | 0 | Setting the value of this attribute to ON will cause the system to filter all non-IP traffic to the Wireless LAN. This should be … |
1.3.6.1.4.1.710.3.2.1.2.5 | brzTranslationMode | 0 | 0 | When this attribute is set to ON, data frames are being translated for the Wireless LAN transmission. If it is set to OFF, tunne… |
1.3.6.1.4.1.710.3.2.1.2.6 | brzWIXSupport | 0 | 0 | This attribute applies to installations with collocated APs. When it is set to ON, a load balancing algorithm is activated, resu… |
1.3.6.1.4.1.710.3.2.1.2.7 | brzWlanNetID | 0 | 0 | This attribute identifies the Wireless LAN network name (Extended Service Set ID) for that device. Stations are not allowed to as… |
1.3.6.1.4.1.710.3.2.1.2.8 | brzAuthenticationType | 0 | 0 | This attribute indicates the authentication algorithm used during the authentication sequence. The value of this attribute is one… |
1.3.6.1.4.1.710.3.2.1.2.9 | brzWlanRTNetID | 0 | 0 | This attribute identifies the run-time Wireless LAN network name (Extended Service Set ID) for that device. Stations are not allo… |
1.3.6.1.4.1.710.3.2.1.2.10 | brzApRedundancySupport | 0 | 0 | Setting the value of this attribute to ON will cause the Access-Point to discontinue sending beacons to the Wireless LAN after no… |
1.3.6.1.4.1.710.3.2.1.2.11 | brzWlanRelayUnicast | 0 | 0 | This attribute enables the relaying of unicast frames on the WLAN within the BSS. Setting this attribute to OFF means that unicas… |
1.3.6.1.4.1.710.3.2.1.2.12 | brzWlanRelayBroadcast | 0 | 0 | This attribute enables the relaying of broadcast frames on the WLAN within the BSS. Setting this attribute to OFF means that broa… |
1.3.6.1.4.1.710.3.2.1.2.14 | brzStaNumForLargeCW | 0 | 0 | This attribute sets the minimum number of stations in this cell that will cause this unit to use large CW, else this unit will us… |
1.3.6.1.4.1.710.3.2.1.2.15 | brzPowerMngMode | 0 | 0 | This attribute describes the current power management mode of the station. The allowed values are ACTIVE (for normal mode of oper… |
1.3.6.1.4.1.710.3.2.1.2.16 | brzACKDelayed | 0 | 0 | This attribute applies to installations with collocated APs. When it is set to ON, a load balancing algorithm is activated, resu… |
1.3.6.1.4.1.710.3.2.1.2.17 | brzDTIMPperiod | 0 | 0 | This attribute defines the rate of DTIM frames. The value is expressed in Beacon Intervals. This attribute is applicable only in… |
1.3.6.1.4.1.710.3.2.1.2.18 | brzPowerMngBitTestMode | 0 | 0 | This attribute describes the current power management bit test mode of the AP. The allowed values are DISABLED (for normal mode o… |
1.3.6.1.4.1.710.3.2.1.2.19 | brzBeaconInterval | 0 | 0 | This attribute defines the rate of Beacon frames. The value is expressed in Dwells. This attribute is applicable only in AP's. |
1.3.6.1.4.1.710.3.2.1.2.20 | brzPowerSaveSupport | 0 | 0 | This attribute defines the power save support. 0 - Power Save support disabled 1 - Power Save support enabled 2 - Enable Power Sav… |
1.3.6.1.4.1.710.3.2.1.2.21 | brzWlanAssocAge | 0 | 0 | This attribute defines the Association Aging Period. |
1.3.6.1.4.1.710.3.2.1.2.22 | brzEnableVoice | 0 | 0 | This attribute Enables voice priority over other transmissions. This attribute is applicable only in AP's. |
1.3.6.1.4.1.710.3.2.1.2.26 | brzNonActiveCodeState | 0 | 0 | This attribute displays the current non active code state. WARNING: Activate this attribute will cause substantial degradation in… |
1.3.6.1.4.1.710.3.2.1.2.27 | brzDisplayNonActiveCodeVersion | 0 | 0 | This attribute displays the active code version and the non active code version. |
1.3.6.1.4.1.710.3.2.1.2.28 | brzIntelligentBridgingPeriod | 0 | 0 | This attribute defines the Intelligent Bridging Period in seconds. |