This attribute describes the current power management bit test mode of
the AP. The allowed values are DISABLED (for normal mode
of operation), and ENABLED.
Parsed from file BREEZECOM-MIB.mib
Module: BREEZECOM-MIB
Vendor: Lannair Ltd.
Module: BREEZECOM-MIB
[Automatically extracted from oidview.com]
brzPowerMngBitTestMode OBJECT-TYPE SYNTAX INTEGER{ disabled (1), enabled (2) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute describes the current power management bit test mode of the AP. The allowed values are DISABLED (for normal mode of operation), and ENABLED." ::= { sysParams 18 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.710.3.2.1.2.1 | brzHWMacAddress | 0 | 0 | The Hardware MAC address of the device. |
| 1.3.6.1.4.1.710.3.2.1.2.2 | brzApplTunneling | 0 | 0 | This attribute specifies the device tunneling mode, as follows: ipx - The device will enable IPX tunneling only. apple-ta… |
| 1.3.6.1.4.1.710.3.2.1.2.3 | brzPositiveBrg | 0 | 0 | This attribute specifies the Wired to Wireless LAN bridging mode at the AP, as follows: reject-unknown - The AP forwards to the … |
| 1.3.6.1.4.1.710.3.2.1.2.4 | brzIpFilter | 0 | 0 | Setting the value of this attribute to ON will cause the system to filter all non-IP traffic to the Wireless LAN. This should be … |
| 1.3.6.1.4.1.710.3.2.1.2.5 | brzTranslationMode | 0 | 0 | When this attribute is set to ON, data frames are being translated for the Wireless LAN transmission. If it is set to OFF, tunne… |
| 1.3.6.1.4.1.710.3.2.1.2.6 | brzWIXSupport | 0 | 0 | This attribute applies to installations with collocated APs. When it is set to ON, a load balancing algorithm is activated, resu… |
| 1.3.6.1.4.1.710.3.2.1.2.7 | brzWlanNetID | 0 | 0 | This attribute identifies the Wireless LAN network name (Extended Service Set ID) for that device. Stations are not allowed to as… |
| 1.3.6.1.4.1.710.3.2.1.2.8 | brzAuthenticationType | 0 | 0 | This attribute indicates the authentication algorithm used during the authentication sequence. The value of this attribute is one… |
| 1.3.6.1.4.1.710.3.2.1.2.9 | brzWlanRTNetID | 0 | 0 | This attribute identifies the run-time Wireless LAN network name (Extended Service Set ID) for that device. Stations are not allo… |
| 1.3.6.1.4.1.710.3.2.1.2.10 | brzApRedundancySupport | 0 | 0 | Setting the value of this attribute to ON will cause the Access-Point to discontinue sending beacons to the Wireless LAN after no… |
| 1.3.6.1.4.1.710.3.2.1.2.11 | brzWlanRelayUnicast | 0 | 0 | This attribute enables the relaying of unicast frames on the WLAN within the BSS. Setting this attribute to OFF means that unicas… |
| 1.3.6.1.4.1.710.3.2.1.2.12 | brzWlanRelayBroadcast | 0 | 0 | This attribute enables the relaying of broadcast frames on the WLAN within the BSS. Setting this attribute to OFF means that broa… |
| 1.3.6.1.4.1.710.3.2.1.2.13 | brzApRedundancyLimit | 0 | 0 | This attribute sets the time until an Access-Point discontinues sending beacons to the Wireless LAN when no multicast or unicast… |
| 1.3.6.1.4.1.710.3.2.1.2.14 | brzStaNumForLargeCW | 0 | 0 | This attribute sets the minimum number of stations in this cell that will cause this unit to use large CW, else this unit will us… |
| 1.3.6.1.4.1.710.3.2.1.2.15 | brzPowerMngMode | 0 | 0 | This attribute describes the current power management mode of the station. The allowed values are ACTIVE (for normal mode of oper… |
| 1.3.6.1.4.1.710.3.2.1.2.16 | brzACKDelayed | 0 | 0 | This attribute applies to installations with collocated APs. When it is set to ON, a load balancing algorithm is activated, resu… |
| 1.3.6.1.4.1.710.3.2.1.2.17 | brzDTIMPperiod | 0 | 0 | This attribute defines the rate of DTIM frames. The value is expressed in Beacon Intervals. This attribute is applicable only in… |
| 1.3.6.1.4.1.710.3.2.1.2.19 | brzBeaconInterval | 0 | 0 | This attribute defines the rate of Beacon frames. The value is expressed in Dwells. This attribute is applicable only in AP's. |
| 1.3.6.1.4.1.710.3.2.1.2.20 | brzPowerSaveSupport | 0 | 0 | This attribute defines the power save support. 0 - Power Save support disabled 1 - Power Save support enabled 2 - Enable Power Sav… |
| 1.3.6.1.4.1.710.3.2.1.2.21 | brzWlanAssocAge | 0 | 0 | This attribute defines the Association Aging Period. |
| 1.3.6.1.4.1.710.3.2.1.2.22 | brzEnableVoice | 0 | 0 | This attribute Enables voice priority over other transmissions. This attribute is applicable only in AP's. |
| 1.3.6.1.4.1.710.3.2.1.2.26 | brzNonActiveCodeState | 0 | 0 | This attribute displays the current non active code state. WARNING: Activate this attribute will cause substantial degradation in… |
| 1.3.6.1.4.1.710.3.2.1.2.27 | brzDisplayNonActiveCodeVersion | 0 | 0 | This attribute displays the active code version and the non active code version. |
| 1.3.6.1.4.1.710.3.2.1.2.28 | brzIntelligentBridgingPeriod | 0 | 0 | This attribute defines the Intelligent Bridging Period in seconds. |