Enable/disable Transparent Link Pass through.
If the Peer's remote link goes down, the link down
is passed on to the other end while the OAM channel
is still active.
Parsed from file TNI-MIB.mib
Module: TNI-MIB
Vendor: Transition Engineering Inc.
Module: TNI-MIB
[Automatically extracted from oidview.com]
sfbrm100SysTLPT OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/disable Transparent Link Pass through. If the Peer's remote link goes down, the link down is passed on to the other end while the OAM channel is still active." ::= { sfbrm100SystemEntry 25 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.868.2.3.1.1.1.1.1 | sfbrm100SysLocPortIndex | 0 | 0 | The local port index of the port to which the peer is connected. The local device has an index of 0. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.2 | sfbrm100SysSecIndex | 0 | 0 | Secondary index for the table. It is always 1. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.3 | sfbrm100SysGrpString | 0 | 0 | Group membership string. See http://www.transition.com/pshelp/configmgmt1.html |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.4 | sfbrm100SysMRevision | 0 | 0 | The marketing revision of this device. See http://www.transition.com/pshelp/mrevision.html |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.5 | sfbrm100SysCfgMatch | 0 | 0 | See http://www.transition.com/pshelp/configmgmt1.html |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.6 | sfbrm100SysBootLoaderRevision | 0 | 0 | The bootloader revision level for this device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.7 | sfbrm100SysFirmwareRevision | 0 | 0 | The firmware revision level for this device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.8 | sfbrm100SysSerialNumber | 0 | 0 | The serial number of this device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.9 | sfbrm100SysBIAddress | 0 | 0 | The serial number (BIA) of the cabinet in which the device is installed. If it is a stand-alone this is zero. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.10 | sfbrm100SysSlotIndex | 0 | 0 | The Slot number if installed in a chassis. Zero if stand-alone. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.11 | sfbrm100SysNumPorts | 0 | 0 | The Number of ports on this device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.12 | sfbrm100SysMACAddress | 0 | 0 | The MAC address used in MGMT frames and IP Packets. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.13 | sfbrm100SystemReset | 0 | 0 | Set this to reset(1) to cause the system to reboot. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.14 | sfbrm100SysIPaddress | 0 | 0 | The IPV4 address of the device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.15 | sfbrm100SysSubnetMask | 0 | 0 | The subnet mask associated with the IP address of the device. The value of the mask is an IP address with all the network bits s… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.16 | sfbrm100SysDefGateway | 0 | 0 | The default gateway for the device |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.17 | sfbrm100SysSNMPTrapMgr | 0 | 0 | The IPV4 address of the SNMP trap manager. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.18 | sfbrm100SysRadiusAuth | 0 | 0 | RADIUS authentication can be enabled or disabled using this variable. RADIUS Authentication is used for management access only. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.19 | sfbrm100SysRadiusServerAddr | 0 | 0 | The IPV4 address of the Radius Server. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.20 | sfbrm100SysRadiusSecret | 0 | 0 | The shared secret between the device and RADIUS server. A read returns 'xxx' for security. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.21 | sfbrm100SysRadiusRetry | 0 | 0 | The number of times the device would try to contact the RADIUS server, when there is any communication problem. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.22 | sfbrm100SysRadiusTimeout | 0 | 0 | The number of seconds the device would wait for the server response before it times out. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.23 | sfbrm100SysDHCPEnable | 0 | 0 | Enable/Disable DHCP. A reset of the system is needed. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.24 | sfbrm100SysSerialAccess | 0 | 0 | Enable/Disable access to USB Port. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.26 | sfbrm100SysTFTPServerAddr | 0 | 0 | The IPV4 address of the TFTP Server. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.27 | sfbrm100SysTFTPfilename | 0 | 0 | The Firmware file to be downloaded from the TFTP Server for upgrading. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.28 | sfbrm100SysTFTPCmd | 0 | 0 | To initiate a TFTP upgrading, set the value to perform(1), the systems resets and the bootloader is invoked to perform the upgrad… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.29 | sfbrm100SysTFTPServerIgnore | 0 | 0 | In some configuration, when the device uses DHCP to get its IP address, it also receives the tftpserver address for upgrading. Wh… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.30 | sfbrm100SysMgmtVlanId | 0 | 0 | VLAN Id for the management frames. This is valid only when vlan is enabled. This creates a secure channel for all management traf… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.31 | sfbrm100SysSNMPAccess | 0 | 0 | The SNMP access to the device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.32 | sfbrm100SysIPAccess | 0 | 0 | IP management access to the device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.33 | sfbrm100SysLastGaspPdu | 0 | 0 | This mib variable is used to choose the type of PDU to be generated on the last gasp event. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.34 | sfbrm100SysLastGaspPort | 0 | 0 | When there are multiple OAM enabled ports, this variable decides which port to send the Dying gasp OAM PDU. The default is Port 2… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.35 | sfbrm100SysLocalLPT | 0 | 0 | When the monitored port (sfbrm100SysLPTPort)link goes down, the other port is brought down when this is enabled. This is also na… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.36 | sfbrm100SysLPTPort | 0 | 0 | This determines the port, on which the Transparent Link pass through and the Selective/local Link pass through will be active. A… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.37 | sfbrm100SysAutoUpgrade | 0 | 0 | When enabled, auto upgrade of this device can be done by its peer. By default this is 'enabled(1)'. When disabled, the peer shou… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.38 | sfbrm100SysFormFactorSlot | 0 | 0 | This read-only variable gives the number of slots in a chassis this unit occupies if its a chassis card. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.39 | sfbrm100SysFormFactorPort | 0 | 0 | This read-only variables gives type of ports present on this board. The values and description for each board : 1 - xFBRM 10/100… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.40 | sfbrm100SysOAMPort | 0 | 0 | When only one OAM session is allowed, this determines the port that will be used for sending and receiving OAM messages. This als… |