The Firmware file to be downloaded from the TFTP Server
for upgrading.
Parsed from file TNI-MIB.mib
Module: TNI-MIB
Vendor: Transition Engineering Inc.
Module: TNI-MIB
[Automatically extracted from oidview.com]
sfbrm100SysTFTPfilename OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "The Firmware file to be downloaded from the TFTP Server for upgrading." ::= { sfbrm100SystemEntry 27 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.868.2.3.1.1.1.1.1 | sfbrm100SysLocPortIndex | 0 | 0 | The local port index of the port to which the peer is connected. The local device has an index of 0. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.2 | sfbrm100SysSecIndex | 0 | 0 | Secondary index for the table. It is always 1. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.3 | sfbrm100SysGrpString | 0 | 0 | Group membership string. See http://www.transition.com/pshelp/configmgmt1.html |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.4 | sfbrm100SysMRevision | 0 | 0 | The marketing revision of this device. See http://www.transition.com/pshelp/mrevision.html |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.5 | sfbrm100SysCfgMatch | 0 | 0 | See http://www.transition.com/pshelp/configmgmt1.html |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.6 | sfbrm100SysBootLoaderRevision | 0 | 0 | The bootloader revision level for this device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.7 | sfbrm100SysFirmwareRevision | 0 | 0 | The firmware revision level for this device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.8 | sfbrm100SysSerialNumber | 0 | 0 | The serial number of this device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.9 | sfbrm100SysBIAddress | 0 | 0 | The serial number (BIA) of the cabinet in which the device is installed. If it is a stand-alone this is zero. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.10 | sfbrm100SysSlotIndex | 0 | 0 | The Slot number if installed in a chassis. Zero if stand-alone. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.11 | sfbrm100SysNumPorts | 0 | 0 | The Number of ports on this device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.12 | sfbrm100SysMACAddress | 0 | 0 | The MAC address used in MGMT frames and IP Packets. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.13 | sfbrm100SystemReset | 0 | 0 | Set this to reset(1) to cause the system to reboot. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.14 | sfbrm100SysIPaddress | 0 | 0 | The IPV4 address of the device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.15 | sfbrm100SysSubnetMask | 0 | 0 | The subnet mask associated with the IP address of the device. The value of the mask is an IP address with all the network bits s… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.16 | sfbrm100SysDefGateway | 0 | 0 | The default gateway for the device |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.17 | sfbrm100SysSNMPTrapMgr | 0 | 0 | The IPV4 address of the SNMP trap manager. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.18 | sfbrm100SysRadiusAuth | 0 | 0 | RADIUS authentication can be enabled or disabled using this variable. RADIUS Authentication is used for management access only. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.19 | sfbrm100SysRadiusServerAddr | 0 | 0 | The IPV4 address of the Radius Server. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.20 | sfbrm100SysRadiusSecret | 0 | 0 | The shared secret between the device and RADIUS server. A read returns 'xxx' for security. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.21 | sfbrm100SysRadiusRetry | 0 | 0 | The number of times the device would try to contact the RADIUS server, when there is any communication problem. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.22 | sfbrm100SysRadiusTimeout | 0 | 0 | The number of seconds the device would wait for the server response before it times out. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.23 | sfbrm100SysDHCPEnable | 0 | 0 | Enable/Disable DHCP. A reset of the system is needed. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.24 | sfbrm100SysSerialAccess | 0 | 0 | Enable/Disable access to USB Port. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.25 | sfbrm100SysTLPT | 0 | 0 | Enable/disable Transparent Link Pass through. If the Peer's remote link goes down, the link down is passed on to the other end wh… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.26 | sfbrm100SysTFTPServerAddr | 0 | 0 | The IPV4 address of the TFTP Server. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.28 | sfbrm100SysTFTPCmd | 0 | 0 | To initiate a TFTP upgrading, set the value to perform(1), the systems resets and the bootloader is invoked to perform the upgrad… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.29 | sfbrm100SysTFTPServerIgnore | 0 | 0 | In some configuration, when the device uses DHCP to get its IP address, it also receives the tftpserver address for upgrading. Wh… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.30 | sfbrm100SysMgmtVlanId | 0 | 0 | VLAN Id for the management frames. This is valid only when vlan is enabled. This creates a secure channel for all management traf… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.31 | sfbrm100SysSNMPAccess | 0 | 0 | The SNMP access to the device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.32 | sfbrm100SysIPAccess | 0 | 0 | IP management access to the device. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.33 | sfbrm100SysLastGaspPdu | 0 | 0 | This mib variable is used to choose the type of PDU to be generated on the last gasp event. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.34 | sfbrm100SysLastGaspPort | 0 | 0 | When there are multiple OAM enabled ports, this variable decides which port to send the Dying gasp OAM PDU. The default is Port 2… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.35 | sfbrm100SysLocalLPT | 0 | 0 | When the monitored port (sfbrm100SysLPTPort)link goes down, the other port is brought down when this is enabled. This is also na… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.36 | sfbrm100SysLPTPort | 0 | 0 | This determines the port, on which the Transparent Link pass through and the Selective/local Link pass through will be active. A… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.37 | sfbrm100SysAutoUpgrade | 0 | 0 | When enabled, auto upgrade of this device can be done by its peer. By default this is 'enabled(1)'. When disabled, the peer shou… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.38 | sfbrm100SysFormFactorSlot | 0 | 0 | This read-only variable gives the number of slots in a chassis this unit occupies if its a chassis card. |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.39 | sfbrm100SysFormFactorPort | 0 | 0 | This read-only variables gives type of ports present on this board. The values and description for each board : 1 - xFBRM 10/100… |
| 1.3.6.1.4.1.868.2.3.1.1.1.1.40 | sfbrm100SysOAMPort | 0 | 0 | When only one OAM session is allowed, this determines the port that will be used for sending and receiving OAM messages. This als… |