Each bit represents ports on the switch.
These bits restrict where this port can send frames to, setting the
bits to zero will disable this port's ability to egress frames out of the
indicated port.
Ex: Port 0 is represented by bit 0 in the bitmap.
By default all ports can send to all ports.
Parsed from file TNI-MIB.mib
Module: TNI-MIB
Vendor: Transition Engineering Inc.
Module: TNI-MIB
[Automatically extracted from oidview.com]
sfbrm100PortBasedVLANTbl OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Each bit represents ports on the switch. These bits restrict where this port can send frames to, setting the bits to zero will disable this port's ability to egress frames out of the indicated port. Ex: Port 0 is represented by bit 0 in the bitmap. By default all ports can send to all ports." ::= { sfbrm100PortEntry 55 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.868.2.3.1.3.1.1.1 | sfbrm100PortLocIndex | 0 | 0 | Uniquely indentifies each port on the device. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.2 | sfbrm100PortRmtIndex | 0 | 0 | Uniquely indentifies each port on the peer device. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.3 | sfbrm100PortGrpString | 0 | 0 | Description string for each port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.4 | sfbrm100PortConnType | 0 | 0 | The actual physical connector on the port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.5 | sfbrm100PortOAMState | 0 | 0 | This object is used to provision the default administrative enable/disable of OAM on this interface. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.6 | sfbrm100PortOAMModeCtrl | 0 | 0 | This object can be used to provision the OAM mode for this interface. In auto(1) mode , the interface is set to active/passive d… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.7 | sfbrm100PortRmtLoopback | 0 | 0 | Initiates remote loopback, if supported by remote peer. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.8 | sfbrm100PortIgnoreLoopback | 0 | 0 | If enabled, the device ignores any loopback requests. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.9 | sfbrm100PortAdvPause | 0 | 0 | Specifies the Pause frame advertisement capability. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.10 | sfbrm100PortAdv1000FDX | 0 | 0 | This configuration setting controls whether or not this port advertises willingness to connect at 1000Mbps, full duplex. This is… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.11 | sfbrm100PortAdv1000HDX | 0 | 0 | This configuration setting controls whether or not this port advertises willingness to connect at 1000Mbps, half duplex. This is… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.12 | sfbrm100PortAdv100FDX | 0 | 0 | This configuration setting controls whether or not this port advertises willingness to connect at 100Mbps, full duplex. This is … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.13 | sfbrm100PortAdv100HDX | 0 | 0 | This configuration setting controls whether or not this port advertises willingness to connect at 100Mbps, half duplex. This is … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.14 | sfbrm100PortAdv10FDX | 0 | 0 | This configuration setting controls whether or not this port advertises willingness to connect at 10Mbps, full duplex. This is i… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.15 | sfbrm100PortAdv10HDX | 0 | 0 | This configuration setting controls whether or not this port advertises willingness to connect at 100Mbps, half duplex. This is … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.16 | sfbrm100PortAutoneg | 0 | 0 | Enable/Disable autonegotiation on this port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.17 | sfbrm100PortFDuplex | 0 | 0 | This is a configuration setting that controls the duplex mode; fullDuplex is full duplex and halfDuplex is half duplex. This is v… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.18 | sfbrm100PortFSpeed | 0 | 0 | This is a configuration setting that controls the speed; This is valid only when autonegotiation is disabled. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.19 | sfbrm100PortLpPauseAbility | 0 | 0 | Link Partner's pause capability. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.20 | sfbrm100PortLpAutonegAbility | 0 | 0 | The autonegotiation advertisement mode can be set using the options of this variable. spdAutoDupAuto(1) - Advertise all speed a… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.21 | sfbrm100PortLinkState | 0 | 0 | Link status on this port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.22 | sfbrm100PortAutonegState | 0 | 0 | The autonegotiation state or if autonegotiation is disabled it returns resolved(1). |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.23 | sfbrm100PortDuplex | 0 | 0 | The port's duplex value when autonegotiation is resolved. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.24 | sfbrm100PortSpeed | 0 | 0 | The port's duplex value when autonegotiation is resolved |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.25 | sfbrm100PortFEFI | 0 | 0 | Enabled/Disable Far-end Fault detection. Read-only value notApplicable is returned for unsupported Ethernet PHY's. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.26 | sfbrm100PortAutocross | 0 | 0 | This is applicable for supporting PHY's. If set to mdi(1) the transmit happens on pair 1 & 2 and receive on 3 & 4. If set to md… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.27 | sfbrm100PortLock | 0 | 0 | When enabled, it disables the automatic learning of source addresses on this port and drops frames where the SA does not exist i… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.28 | sfbrm100PortIgnoreWrongData | 0 | 0 | Ignores interrupts caused by reception of frames whose source address is not assigned to this port. When disabled(2), generates … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.29 | sfbrm100PortIGMPSnoop | 0 | 0 | When enabled all IGMP frames are directed to the CPU overriding the Destination address. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.30 | sfbrm100PortDoubleTagging | 0 | 0 | When set to enabled, the frames which have 802.3ac tag with IEEE standard ether-type of 0x8100 are examined for tags. On Ingress … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.31 | sfbrm100PortUseIPTC | 0 | 0 | When enabled, IP priority fields are used for Traffic class of priority data. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.32 | sfbrm100PortUseTagTC | 0 | 0 | When enabled, the IEEE 802.1p fields are used for traffic class of priority data if the frame is IEEE 802.1ac tagged. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.33 | sfbrm100PortUseBothTC | 0 | 0 | sfbrm100PortUseBothtC |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.34 | sfbrm100PortVLANTunnel | 0 | 0 | For all unicast and multicast frames with destination address defined as 'static' in the address database port-based VLAN maskin… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.35 | sfbrm100PortFwdUnknown | 0 | 0 | When enabled, all unicast frames with unknown destination address are allowed to egress this port( assuming VLAN settings allow … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.36 | sfbrm100PortDefForward | 0 | 0 | When enabled, all multicast frames with unknown destination address are allowed to egress this port( assuming VLAN settings allo… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.37 | sfbrm100PortAdminState | 0 | 0 | Set port state administratively up or down. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.38 | sfbrm100PortVTUPriOverride | 0 | 0 | When disabled, normal switch operation is done. When enabled, VTU Priority override occurs. i.e The determined VID priority takes… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.39 | sfbrm100PortSAPriOverride | 0 | 0 | When enabled, Source address decides the priority as per the address database entry rules. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.40 | sfbrm100PortDAPriOverride | 0 | 0 | When enabled, Destination address decides the priority as per the address database entry rules. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.41 | sfbrm100PortVLANStatus | 0 | 0 | 802.1Q VLAN setting : vlanDisabled - 802.1Q is disabled. fallback - The frame is not discarded if the VID is not in the VLAN Db… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.42 | sfbrm100PortDiscardTagged | 0 | 0 | All ingress tagged frames are discarded if enabled. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.43 | sfbrm100PortDiscardUntagged | 0 | 0 | All untagged ingress frames are discarded if enabled. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.44 | sfbrm100PortEgressMonitor | 0 | 0 | Any frame that egress this port is also sent to the egress monitor destination port. Not applicable for 2-port device. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.45 | sfbrm100PortIngressMonitor | 0 | 0 | Any frame that ingress this port is also sent to the ingress monitor destination port. Not applicable for 2-port device |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.46 | sfbrm100PortPri3IngressRateCtrl | 0 | 0 | Ingress rate limit for Priority 3 frames, but not faster than port speed. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.47 | sfbrm100PortPri2IngressRateCtrl | 0 | 0 | Ingress rate limit for Priority 2 frames, but not faster than port speed. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.48 | sfbrm100PortPri1IngressRateCtrl | 0 | 0 | Ingress rate limit for Priority 1 frames, but not faster than port speed. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.49 | sfbrm100PortPri0IngressRate | 0 | 0 | Ingress rate for Priority 0 frames in bits per second, but not faster than port speed. Priority 0 frames are discarded after the … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.50 | sfbrm100PortIngressLimitMode | 0 | 0 | Ingress Limit mode. all(1) - Limits and counts all frames bCastMCastFloodedUCast(2) - Limits and counts all broadcast, mul… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.51 | sfbrm100PortEgressRate | 0 | 0 | Egress priority rate in bits per seconds. This affects the port's effective transmission rate. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.52 | sfbrm100PortDefaultPriority | 0 | 0 | The default priority of the frame if its not IEEE tagged or not IP frames or no other priority overides are active for this fram… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.53 | sfbrm100PortForceDefVLANId | 0 | 0 | Force to use the sfbrm100PortDefaultVLANId when 802.1Q is enabled on this port. The frames actual VLAN id is replaced with the de… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.54 | sfbrm100PortDefaultVLANId | 0 | 0 | The default VLAN Id of the port. All untagged frames that are to exit tagged will use the VID of the ingress port on exit. This V… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.56 | sfbrm100PortIEEEPriRemap0 | 0 | 0 | All Frames with priority 0 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.57 | sfbrm100PortIEEEPriRemap1 | 0 | 0 | All Frames with priority 1 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.58 | sfbrm100PortIEEEPriRemap2 | 0 | 0 | All Frames with priority 2 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.59 | sfbrm100PortIEEEPriRemap3 | 0 | 0 | All Frames with priority 3 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.60 | sfbrm100PortIEEEPriRemap4 | 0 | 0 | All Frames with priority 4 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.61 | sfbrm100PortIEEEPriRemap5 | 0 | 0 | All Frames with priority 5 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.62 | sfbrm100PortIEEEPriRemap6 | 0 | 0 | All Frames with priority 6 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.63 | sfbrm100PortIEEEPriRemap7 | 0 | 0 | All Frames with priority 7 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.64 | sfbrm100PortVCTest | 0 | 0 | The virtual cable test can be done using this variable set to perform(1), otherwise the Read-only value notApplicable(2) will be… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.65 | sfbrm100PortVCTxMDI0Status | 0 | 0 | The test status of the Tx pair or MDI[0](Gigabit port) depending on port type. normal(1) - Test was successful, cable is norm… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.66 | sfbrm100PortTxMDI0Dist | 0 | 0 | The cable distance of the Tx pair or MDI[0](Gigabit port) from the tested port. In case of sfbrm100PortVCRxMDIXStatus having a v… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.67 | sfbrm100PortVCRxMDI1Status | 0 | 0 | The test status of the Rx or MDI[1](Gigabit port) depending on port type. normal(1) - Test was successful, cable is normal (n… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.68 | sfbrm100PortRxMDI1Dist | 0 | 0 | The cable distance of the Rx pair or MDI[1](Gigabit port) from the tested port. In case of sfbrm100PortVCRxMDIXStatus having a v… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.69 | sfbrm100PortVCMDI2Status | 0 | 0 | The test status of the MDI[2](Gigabit port), 0 otherwise. normal(1) - Test was successful, cable is normal (no short or open … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.70 | sfbrm100PortMDI2Dist | 0 | 0 | The cable distance of the MDI[2](if Gigabit port else notApplicable(6)) from the test port. In case of sfbrm100PortVCRxMDIXStatu… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.71 | sfbrm100PortVCMDI3Status | 0 | 0 | The test status of the MDI[3](Gigabit port), 0 otherwise. normal(1) - Test was successful, cable is normal (no short or open … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.72 | sfbrm100PortMDI3Dist | 0 | 0 | The cable distance of the MDI[3](if Gigabit port else notApplicable(6)) from the tested port. In case of sfbrm100PortVCRxMDIXSta… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.73 | sfbrm100PortResetCounters | 0 | 0 | Resets all the port counters for this port. A read returns read-only value donothing(2). |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.74 | sfbrm100PortIPTrafficAccess | 0 | 0 | Allow/block IP management traffic on this port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.75 | sfbrm100PortResetOAMCounters | 0 | 0 | Resets all OAM counters for this port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.76 | sfbrm100PortForceAutoUpgrade | 0 | 0 | Force Automatic firmware upgrade on this peer, when the peer has its auto upgrade turned off. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.77 | sfbrm100PortModeType | 0 | 0 | The Interface mode. The capabilities of the interface. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.78 | sfbrm100PortOAMMode | 0 | 0 | The OAM mode for this port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.79 | sfbrm100PortPhyNumber | 0 | 0 | This gives the physical port number on the hardware switch. This is useful in computing the port based VLAN setting for this port… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.80 | sfbrm100PortIngressRateLimit2 | 0 | 0 | Ingress bandwidth limiting in bits per second, but not faster than port speed. Frames are discarded if the ingress rate selected … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.81 | sfbrm100PortEgressRateLimit2 | 0 | 0 | Egress bandwidth limiting in bits per second, but not faster than port speed. Frames are discarded if over the limit. Devices whi… |