Resets all the port counters for this port. A read returns read-only value donothing(2).
Parsed from file TNI-MIB.mib
Module: TNI-MIB
Vendor: Transition Engineering Inc.
Module: TNI-MIB
[Automatically extracted from oidview.com]
sfbrm100PortResetCounters OBJECT-TYPE SYNTAX INTEGER { reset(1), donothing(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Resets all the port counters for this port. A read returns read-only value donothing(2)." ::= { sfbrm100PortEntry 73 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.868.2.3.1.3.1.1.1 | sfbrm100PortLocIndex | 0 | 0 | Uniquely indentifies each port on the device. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.2 | sfbrm100PortRmtIndex | 0 | 0 | Uniquely indentifies each port on the peer device. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.3 | sfbrm100PortGrpString | 0 | 0 | Description string for each port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.4 | sfbrm100PortConnType | 0 | 0 | The actual physical connector on the port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.5 | sfbrm100PortOAMState | 0 | 0 | This object is used to provision the default administrative enable/disable of OAM on this interface. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.6 | sfbrm100PortOAMModeCtrl | 0 | 0 | This object can be used to provision the OAM mode for this interface. In auto(1) mode , the interface is set to active/passive d… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.7 | sfbrm100PortRmtLoopback | 0 | 0 | Initiates remote loopback, if supported by remote peer. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.8 | sfbrm100PortIgnoreLoopback | 0 | 0 | If enabled, the device ignores any loopback requests. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.9 | sfbrm100PortAdvPause | 0 | 0 | Specifies the Pause frame advertisement capability. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.10 | sfbrm100PortAdv1000FDX | 0 | 0 | This configuration setting controls whether or not this port advertises willingness to connect at 1000Mbps, full duplex. This is… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.11 | sfbrm100PortAdv1000HDX | 0 | 0 | This configuration setting controls whether or not this port advertises willingness to connect at 1000Mbps, half duplex. This is… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.12 | sfbrm100PortAdv100FDX | 0 | 0 | This configuration setting controls whether or not this port advertises willingness to connect at 100Mbps, full duplex. This is … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.13 | sfbrm100PortAdv100HDX | 0 | 0 | This configuration setting controls whether or not this port advertises willingness to connect at 100Mbps, half duplex. This is … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.14 | sfbrm100PortAdv10FDX | 0 | 0 | This configuration setting controls whether or not this port advertises willingness to connect at 10Mbps, full duplex. This is i… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.15 | sfbrm100PortAdv10HDX | 0 | 0 | This configuration setting controls whether or not this port advertises willingness to connect at 100Mbps, half duplex. This is … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.16 | sfbrm100PortAutoneg | 0 | 0 | Enable/Disable autonegotiation on this port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.17 | sfbrm100PortFDuplex | 0 | 0 | This is a configuration setting that controls the duplex mode; fullDuplex is full duplex and halfDuplex is half duplex. This is v… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.18 | sfbrm100PortFSpeed | 0 | 0 | This is a configuration setting that controls the speed; This is valid only when autonegotiation is disabled. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.19 | sfbrm100PortLpPauseAbility | 0 | 0 | Link Partner's pause capability. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.20 | sfbrm100PortLpAutonegAbility | 0 | 0 | The autonegotiation advertisement mode can be set using the options of this variable. spdAutoDupAuto(1) - Advertise all speed a… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.21 | sfbrm100PortLinkState | 0 | 0 | Link status on this port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.22 | sfbrm100PortAutonegState | 0 | 0 | The autonegotiation state or if autonegotiation is disabled it returns resolved(1). |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.23 | sfbrm100PortDuplex | 0 | 0 | The port's duplex value when autonegotiation is resolved. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.24 | sfbrm100PortSpeed | 0 | 0 | The port's duplex value when autonegotiation is resolved |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.25 | sfbrm100PortFEFI | 0 | 0 | Enabled/Disable Far-end Fault detection. Read-only value notApplicable is returned for unsupported Ethernet PHY's. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.26 | sfbrm100PortAutocross | 0 | 0 | This is applicable for supporting PHY's. If set to mdi(1) the transmit happens on pair 1 & 2 and receive on 3 & 4. If set to md… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.27 | sfbrm100PortLock | 0 | 0 | When enabled, it disables the automatic learning of source addresses on this port and drops frames where the SA does not exist i… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.28 | sfbrm100PortIgnoreWrongData | 0 | 0 | Ignores interrupts caused by reception of frames whose source address is not assigned to this port. When disabled(2), generates … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.29 | sfbrm100PortIGMPSnoop | 0 | 0 | When enabled all IGMP frames are directed to the CPU overriding the Destination address. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.30 | sfbrm100PortDoubleTagging | 0 | 0 | When set to enabled, the frames which have 802.3ac tag with IEEE standard ether-type of 0x8100 are examined for tags. On Ingress … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.31 | sfbrm100PortUseIPTC | 0 | 0 | When enabled, IP priority fields are used for Traffic class of priority data. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.32 | sfbrm100PortUseTagTC | 0 | 0 | When enabled, the IEEE 802.1p fields are used for traffic class of priority data if the frame is IEEE 802.1ac tagged. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.33 | sfbrm100PortUseBothTC | 0 | 0 | sfbrm100PortUseBothtC |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.34 | sfbrm100PortVLANTunnel | 0 | 0 | For all unicast and multicast frames with destination address defined as 'static' in the address database port-based VLAN maskin… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.35 | sfbrm100PortFwdUnknown | 0 | 0 | When enabled, all unicast frames with unknown destination address are allowed to egress this port( assuming VLAN settings allow … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.36 | sfbrm100PortDefForward | 0 | 0 | When enabled, all multicast frames with unknown destination address are allowed to egress this port( assuming VLAN settings allo… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.37 | sfbrm100PortAdminState | 0 | 0 | Set port state administratively up or down. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.38 | sfbrm100PortVTUPriOverride | 0 | 0 | When disabled, normal switch operation is done. When enabled, VTU Priority override occurs. i.e The determined VID priority takes… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.39 | sfbrm100PortSAPriOverride | 0 | 0 | When enabled, Source address decides the priority as per the address database entry rules. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.40 | sfbrm100PortDAPriOverride | 0 | 0 | When enabled, Destination address decides the priority as per the address database entry rules. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.41 | sfbrm100PortVLANStatus | 0 | 0 | 802.1Q VLAN setting : vlanDisabled - 802.1Q is disabled. fallback - The frame is not discarded if the VID is not in the VLAN Db… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.42 | sfbrm100PortDiscardTagged | 0 | 0 | All ingress tagged frames are discarded if enabled. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.43 | sfbrm100PortDiscardUntagged | 0 | 0 | All untagged ingress frames are discarded if enabled. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.44 | sfbrm100PortEgressMonitor | 0 | 0 | Any frame that egress this port is also sent to the egress monitor destination port. Not applicable for 2-port device. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.45 | sfbrm100PortIngressMonitor | 0 | 0 | Any frame that ingress this port is also sent to the ingress monitor destination port. Not applicable for 2-port device |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.46 | sfbrm100PortPri3IngressRateCtrl | 0 | 0 | Ingress rate limit for Priority 3 frames, but not faster than port speed. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.47 | sfbrm100PortPri2IngressRateCtrl | 0 | 0 | Ingress rate limit for Priority 2 frames, but not faster than port speed. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.48 | sfbrm100PortPri1IngressRateCtrl | 0 | 0 | Ingress rate limit for Priority 1 frames, but not faster than port speed. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.49 | sfbrm100PortPri0IngressRate | 0 | 0 | Ingress rate for Priority 0 frames in bits per second, but not faster than port speed. Priority 0 frames are discarded after the … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.50 | sfbrm100PortIngressLimitMode | 0 | 0 | Ingress Limit mode. all(1) - Limits and counts all frames bCastMCastFloodedUCast(2) - Limits and counts all broadcast, mul… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.51 | sfbrm100PortEgressRate | 0 | 0 | Egress priority rate in bits per seconds. This affects the port's effective transmission rate. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.52 | sfbrm100PortDefaultPriority | 0 | 0 | The default priority of the frame if its not IEEE tagged or not IP frames or no other priority overides are active for this fram… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.53 | sfbrm100PortForceDefVLANId | 0 | 0 | Force to use the sfbrm100PortDefaultVLANId when 802.1Q is enabled on this port. The frames actual VLAN id is replaced with the de… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.54 | sfbrm100PortDefaultVLANId | 0 | 0 | The default VLAN Id of the port. All untagged frames that are to exit tagged will use the VID of the ingress port on exit. This V… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.55 | sfbrm100PortBasedVLANTbl | 0 | 0 | Each bit represents ports on the switch. These bits restrict where this port can send frames to, setting the bits to zero will di… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.56 | sfbrm100PortIEEEPriRemap0 | 0 | 0 | All Frames with priority 0 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.57 | sfbrm100PortIEEEPriRemap1 | 0 | 0 | All Frames with priority 1 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.58 | sfbrm100PortIEEEPriRemap2 | 0 | 0 | All Frames with priority 2 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.59 | sfbrm100PortIEEEPriRemap3 | 0 | 0 | All Frames with priority 3 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.60 | sfbrm100PortIEEEPriRemap4 | 0 | 0 | All Frames with priority 4 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.61 | sfbrm100PortIEEEPriRemap5 | 0 | 0 | All Frames with priority 5 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.62 | sfbrm100PortIEEEPriRemap6 | 0 | 0 | All Frames with priority 6 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.63 | sfbrm100PortIEEEPriRemap7 | 0 | 0 | All Frames with priority 7 are remapped to this set value inside the switch. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.64 | sfbrm100PortVCTest | 0 | 0 | The virtual cable test can be done using this variable set to perform(1), otherwise the Read-only value notApplicable(2) will be… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.65 | sfbrm100PortVCTxMDI0Status | 0 | 0 | The test status of the Tx pair or MDI[0](Gigabit port) depending on port type. normal(1) - Test was successful, cable is norm… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.66 | sfbrm100PortTxMDI0Dist | 0 | 0 | The cable distance of the Tx pair or MDI[0](Gigabit port) from the tested port. In case of sfbrm100PortVCRxMDIXStatus having a v… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.67 | sfbrm100PortVCRxMDI1Status | 0 | 0 | The test status of the Rx or MDI[1](Gigabit port) depending on port type. normal(1) - Test was successful, cable is normal (n… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.68 | sfbrm100PortRxMDI1Dist | 0 | 0 | The cable distance of the Rx pair or MDI[1](Gigabit port) from the tested port. In case of sfbrm100PortVCRxMDIXStatus having a v… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.69 | sfbrm100PortVCMDI2Status | 0 | 0 | The test status of the MDI[2](Gigabit port), 0 otherwise. normal(1) - Test was successful, cable is normal (no short or open … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.70 | sfbrm100PortMDI2Dist | 0 | 0 | The cable distance of the MDI[2](if Gigabit port else notApplicable(6)) from the test port. In case of sfbrm100PortVCRxMDIXStatu… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.71 | sfbrm100PortVCMDI3Status | 0 | 0 | The test status of the MDI[3](Gigabit port), 0 otherwise. normal(1) - Test was successful, cable is normal (no short or open … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.72 | sfbrm100PortMDI3Dist | 0 | 0 | The cable distance of the MDI[3](if Gigabit port else notApplicable(6)) from the tested port. In case of sfbrm100PortVCRxMDIXSta… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.74 | sfbrm100PortIPTrafficAccess | 0 | 0 | Allow/block IP management traffic on this port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.75 | sfbrm100PortResetOAMCounters | 0 | 0 | Resets all OAM counters for this port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.76 | sfbrm100PortForceAutoUpgrade | 0 | 0 | Force Automatic firmware upgrade on this peer, when the peer has its auto upgrade turned off. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.77 | sfbrm100PortModeType | 0 | 0 | The Interface mode. The capabilities of the interface. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.78 | sfbrm100PortOAMMode | 0 | 0 | The OAM mode for this port. |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.79 | sfbrm100PortPhyNumber | 0 | 0 | This gives the physical port number on the hardware switch. This is useful in computing the port based VLAN setting for this port… |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.80 | sfbrm100PortIngressRateLimit2 | 0 | 0 | Ingress bandwidth limiting in bits per second, but not faster than port speed. Frames are discarded if the ingress rate selected … |
| 1.3.6.1.4.1.868.2.3.1.3.1.1.81 | sfbrm100PortEgressRateLimit2 | 0 | 0 | Egress bandwidth limiting in bits per second, but not faster than port speed. Frames are discarded if over the limit. Devices whi… |