The value of configuration register that will be
used by the supervisor module when the system is
restarted.
This MIB object is only supported in systems with
supervisor modules having ROMMON support.
The lowest four bits of the configuration register
(bits 3,2,1, and 0) form the boot field and the
boot field determines whether the system boots
from as the following:
0000
0001
images on the bootflash
0010 to 1111
images specified in the sysBootVariable
The bit 5(0x0020) indicates whether the
configuration file specified in
sysStartupConfigSourceFile will beused recurringly
or not whenever the system resets. If this bit is
not set, the configuration file(s) specified in
sysStartupConfigSourceFile will only be used once
and the value of sysStartupConfigSourceFile will
be reset to empty string automatically during the
next system reset.
If the bit 6(0x0040) is set, the system will start
with default configuration.
The bits 11,12 (0x0800, 0x1000) are used to
specify the console line speed in ROM monitor mode
as the following:
00
01
10
11
The unspecified bits are not used.
Parsed from file CISCO-STACK-MIB.mib
Module: CISCO-STACK-MIB
The value of configuration register that will be
used by the supervisor module when the system is
restarted.
This MIB object is only supported in systems with
supervisor modules having ROMMON support.
The lowest four bits of the configuration register
(bits 3,2,1, and 0) form the boot field and the
boot field determines whether the system boots
from as the following:
0000
0001
images on the bootflash
0010 to 1111
images specified in the sysBootVariable
The bit 5(0x0020) indicates whether the
configuration file specified in
sysStartupConfigSourceFile will beused recurringly
or not whenever the system resets. If this bit is
not set, the configuration file(s) specified in
sysStartupConfigSourceFile will only be used once
and the value of sysStartupConfigSourceFile will
be reset to empty string automatically during the
next system reset.
If the bit 6(0x0040) is set, the system will start
with default configuration.
The bits 11,12 (0x0800, 0x1000) are used to
specify the console line speed in ROM monitor mode
as the following:
00
01
10
11
The unspecified bits are not used.
sysConfigRegister OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (2))
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The value of configuration register that will be used
by the supervisor module when the system is restarted.
This MIB object is only supported in systems with
supervisor modules having ROMMON support.
The lowest four bits of the configuration register
(bits 3,2,1, and 0) form the boot field and the boot
field determines whether the system boots from as the
following:
0000 -- stay in ROM monitor
0001 -- boot from the first bootable system images
on the bootflash
0010 to 1111
-- boot from the first bootable system images
specified in the sysBootVariable
The bit 5(0x0020) indicates whether the configuration
file specified in sysStartupConfigSourceFile will be
be used recurringly or not whenever the the system
resets. If this bit is not set, the configuration
file(s) specified in sysStartupConfigSourceFile will
only be used once and the value of
sysStartupConfigSourceFile will be reset to empty
string automatically during the next system reset.
If the bit 6(0x0040) is set, the system will start with
default configuration.
The bits 11,12 (0x0800, 0x1000) are used to specify the
console line speed in ROM monitor mode as the following:
00 -- 9600
01 -- 1200
10 -- 4800
11 -- 2400
The unspecified bits are not used."
DEFVAL { fh } -- "01 0F"
View at oid-info.com
The value of configuration register that will be
used by the supervisor module when the system is
restarted.
This MIB object is only supported in systems with
supervisor modules having ROMMON support.
The lowest four bits of the configuration register
(bits 3,2,1, and 0) form the boot field and the
boot field determines whether the system boots
from as the following:
0000
0001
images on the bootflash
0010 to 1111
images specified in the sysBootVariable
The bit 5(0x0020) indicates whether the
configuration file specified in
sysStartupConfigSourceFile will beused recurringly
or not whenever the system resets. If this bit is
not set, the configuration file(s) specified in
sysStartupConfigSourceFile will only be used once
and the value of sysStartupConfigSourceFile will
be reset to empty string automatically during the
next system reset.
If the bit 6(0x0040) is set, the system will start
with default configuration.
The bits 11,12 (0x0800, 0x1000) are used to
specify the console line speed in ROM monitor mode
as the following:
00
01
10
11
The unspecified bits are not used.
Parsed from file cisco-stack-mib.mib.txt
Company: None
Module: CISCO-STACK-MIB
The value of configuration register that will be
used by the supervisor module when the system is
restarted.
This MIB object is only supported in systems with
supervisor modules having ROMMON support.
The lowest four bits of the configuration register
(bits 3,2,1, and 0) form the boot field and the
boot field determines whether the system boots
from as the following:
0000
0001
images on the bootflash
0010 to 1111
images specified in the sysBootVariable
The bit 5(0x0020) indicates whether the
configuration file specified in
sysStartupConfigSourceFile will beused recurringly
or not whenever the system resets. If this bit is
not set, the configuration file(s) specified in
sysStartupConfigSourceFile will only be used once
and the value of sysStartupConfigSourceFile will
be reset to empty string automatically during the
next system reset.
If the bit 6(0x0040) is set, the system will start
with default configuration.
The bits 11,12 (0x0800, 0x1000) are used to
specify the console line speed in ROM monitor mode
as the following:
00
01
10
11
The unspecified bits are not used.
sysConfigRegister OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of configuration register that will be used by the supervisor module when the system is restarted. This MIB object is only supported in systems with supervisor modules having ROMMON support. The lowest four bits of the configuration register (bits 3,2,1, and 0) form the boot field and the boot field determines whether the system boots from as the following: 0000 0001 images on the bootflash 0010 to 1111 images specified in the sysBootVariable The bit 5(0x0020) indicates whether the configuration file specified in sysStartupConfigSourceFile will beused recurringly or not whenever the system resets. If this bit is not set, the configuration file(s) specified in sysStartupConfigSourceFile will only be used once and the value of sysStartupConfigSourceFile will be reset to empty string automatically during the next system reset. If the bit 6(0x0040) is set, the system will start with default configuration. The bits 11,12 (0x0800, 0x1000) are used to specify the console line speed in ROM monitor mode as the following: 00 01 10 11 The unspecified bits are not used." DEFVAL { '010f'h } ::= { systemGrp 36 }
sysConfigRegister OBJECT-TYPE SYNTAX OCTET STRING(SIZE(2)) ACCESS read-write STATUS mandatory DESCRIPTION "The value of configuration register that will be used by the supervisor module when the system is restarted. This MIB object is only supported in systems with supervisor modules having ROMMON support. The lowest four bits of the configuration register (bits 3,2,1, and 0) form the boot field and the boot field determines whether the system boots from as the following: 0000 0001 images on the bootflash 0010 to 1111 images specified in the sysBootVariable The bit 5(0x0020) indicates whether the configuration file specified in sysStartupConfigSourceFile will beused recurringly or not whenever the system resets. If this bit is not set, the configuration file(s) specified in sysStartupConfigSourceFile will only be used once and the value of sysStartupConfigSourceFile will be reset to empty string automatically during the next system reset. If the bit 6(0x0040) is set, the system will start with default configuration. The bits 11,12 (0x0800, 0x1000) are used to specify the console line speed in ROM monitor mode as the following: 00 01 10 11 The unspecified bits are not used." DEFVAL { '010f'H } ::= { systemGrp 36 }
Automatically extracted from Cisco "SNMP v2 MIBs".
sysConfigRegister OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of configuration register that will be used by the supervisor module when the system is restarted. This MIB object is only supported in systems with supervisor modules having ROMMON support. The lowest four bits of the configuration register (bits 3,2,1, and 0) form the boot field and the boot field determines whether the system boots from as the following: 0000 0001 images on the bootflash 0010 to 1111 images specified in the sysBootVariable The bit 5(0x0020) indicates whether the configuration file specified in sysStartupConfigSourceFile will beused recurringly or not whenever the system resets. If this bit is not set, the configuration file(s) specified in sysStartupConfigSourceFile will only be used once and the value of sysStartupConfigSourceFile will be reset to empty string automatically during the next system reset. If the bit 6(0x0040) is set, the system will start with default configuration. The bits 11,12 (0x0800, 0x1000) are used to specify the console line speed in ROM monitor mode as the following: 00 01 10 11 The unspecified bits are not used." DEFVAL { '010f'h } ::= { systemGrp 36 }
sysConfigRegister OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of configuration register that will be used by the supervisor module when the system is restarted. This MIB object is only supported in systems with supervisor modules having ROMMON support. The lowest four bits of the configuration register (bits 3,2,1, and 0) form the boot field and the boot field determines whether the system boots from as the following: 0000 0001 images on the bootflash 0010 to 1111 images specified in the sysBootVariable The bit 5(0x0020) indicates whether the configuration file specified in sysStartupConfigSourceFile will beused recurringly or not whenever the system resets. If this bit is not set, the configuration file(s) specified in sysStartupConfigSourceFile will only be used once and the value of sysStartupConfigSourceFile will be reset to empty string automatically during the next system reset. If the bit 6(0x0040) is set, the system will start with default configuration. The bits 11,12 (0x0800, 0x1000) are used to specify the console line speed in ROM monitor mode as the following: 00 01 10 11 The unspecified bits are not used." DEFVAL { '010f'h } ::= { systemGrp 36 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.9.5.1.1.36.0 | sysConfigRegister | 0 | 0 | None |
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.9.5.1.1.1 | sysMgmtType | 1 | 1 | Type of network management running on this entity. |
1.3.6.1.4.1.9.5.1.1.2 | sysIpAddr | 1 | 1 | This entity's IP address. |
1.3.6.1.4.1.9.5.1.1.3 | sysNetMask | 1 | 1 | This entity's subnet mask. |
1.3.6.1.4.1.9.5.1.1.4 | sysBroadcast | 1 | 1 | This entity's broadcast address. |
1.3.6.1.4.1.9.5.1.1.5 | sysTrapReceiverTable | 1 | 4 | The trap receiver table (0 to 20 entries). This table lists the addresses of Network Management Stations that should receive trap… |
1.3.6.1.4.1.9.5.1.1.6 | sysCommunityTable | 1 | 3 | The community table (4 entries). This table lists community strings and their access levels. When an SNMP message is received by … |
1.3.6.1.4.1.9.5.1.1.7 | sysAttachType | 1 | 1 | The requested concentrator attachment type. For a dual attachment concentrator which can be connected to the trunk ring, the firs… |
1.3.6.1.4.1.9.5.1.1.8 | sysTraffic | 1 | 1 | Traffic meter value, i.e. the percentage of bandwidth utilization for the previous polling interval. |
1.3.6.1.4.1.9.5.1.1.9 | sysReset | 1 | 1 | Writing reset(2) to this object resets the control logic of all modules in the system. Writing resetMinDown(3) to this object res… |
1.3.6.1.4.1.9.5.1.1.10 | sysBaudRate | 1 | 1 | The baud rate in bits per second of the RS-232 port. |
1.3.6.1.4.1.9.5.1.1.11 | sysInsertMode | 1 | 1 | The mode for inserting M-ports into the concentrator ring. |
1.3.6.1.4.1.9.5.1.1.12 | sysClearMacTime | 1 | 1 | The time (in hundredths of a second) since mac counters were last cleared. Writing a 0 to this object causes the mac counters to … |
1.3.6.1.4.1.9.5.1.1.13 | sysClearPortTime | 1 | 1 | The time (in hundredths of a second) since port counters were last cleared. Writing a 0 to this object causes the port counters t… |
1.3.6.1.4.1.9.5.1.1.14 | sysFddiRingTable | 1 | 4 | The fddi ring map table. This table lists the nodes in the FDDI ring(s) to which the system belongs. |
1.3.6.1.4.1.9.5.1.1.15 | sysEnableModem | 1 | 1 | Indicates whether the RS-232 port modem control lines are enabled. |
1.3.6.1.4.1.9.5.1.1.16 | sysEnableRedirects | 1 | 1 | Indicates whether ICMP redirect messages are sent or received by the system. |
1.3.6.1.4.1.9.5.1.1.17 | sysEnableRmon | 1 | 1 | Indicates whether the SNMP agent supports the RMON MIB. |
1.3.6.1.4.1.9.5.1.1.18 | sysArpAgingTime | 1 | 1 | The aging time for the ARP table. |
1.3.6.1.4.1.9.5.1.1.19 | sysTrafficPeak | 1 | 1 | Peak traffic meter value since the last time port counters were cleared or the system started (see sysClearPortTime). |
1.3.6.1.4.1.9.5.1.1.20 | sysTrafficPeakTime | 1 | 1 | The time (in hundredths of a second) since the peak traffic meter value occurred. |
1.3.6.1.4.1.9.5.1.1.21 | sysCommunityRwa | 1 | 1 | When an SNMP message is received by this entity, the community string in the message is compared with this string first. If it ma… |
1.3.6.1.4.1.9.5.1.1.22 | sysCommunityRw | 1 | 1 | When an SNMP message is received by this entity, the community string in the message is compared with this string second. If it m… |
1.3.6.1.4.1.9.5.1.1.23 | sysCommunityRo | 1 | 1 | When an SNMP message is received by this entity, the community string in the message is compared with this string third. If it ma… |
1.3.6.1.4.1.9.5.1.1.24 | sysEnableChassisTraps | 1 | 1 | Indicates whether chassisAlarmOn and chassisAlarmOff traps in this MIB should be generated. |
1.3.6.1.4.1.9.5.1.1.25 | sysEnableModuleTraps | 1 | 1 | Indicates whether moduleUp and moduleDown traps in this MIB should be generated. |
1.3.6.1.4.1.9.5.1.1.26 | sysEnableBridgeTraps | 1 | 1 | Indicates whether newRoot and topologyChange traps in the BRIDGE-MIB (RFC 1493) should be generated. |
1.3.6.1.4.1.9.5.1.1.27 | sysIpVlan | 1 | 1 | This entity's IP address Virtual LAN association. |
1.3.6.1.4.1.9.5.1.1.28 | sysConfigChangeTime | 1 | 1 | The time (in hundredths of a second) since the configuration of the system was last changed. |
1.3.6.1.4.1.9.5.1.1.29 | sysEnableRepeaterTraps | 1 | 1 | Indicates whether the traps in the REPEATER-MIB (RFC1516) should be generated. |
1.3.6.1.4.1.9.5.1.1.30 | sysBannerMotd | 1 | 1 | Message of the day banner which is displayed on the Command Line Interface before log in. |
1.3.6.1.4.1.9.5.1.1.31 | sysEnableIpPermitTraps | 1 | 1 | Indicates whether the IP permit traps in this MIB should be generated. |
1.3.6.1.4.1.9.5.1.1.32 | sysTrafficMeterTable | 1 | 5 | The system traffic meter table. This table lists the traffic meters available in the system. |
1.3.6.1.4.1.9.5.1.1.33 | sysEnableVmpsTraps | 1 | 1 | Indicates whether the vmVmpsChange trap defined in CISCO-VLAN-MEMBERSHIP-MIB should be generated. |
1.3.6.1.4.1.9.5.1.1.34 | sysConfigChangeInfo | 1 | 1 | Indicates which NVRAM block is changed by whom. |
1.3.6.1.4.1.9.5.1.1.35 | sysEnableConfigTraps | 1 | 1 | Indicates whether sysConfigChange trap in this MIB should be generated. |
1.3.6.1.4.1.9.5.1.1.37 | sysBootVariable | 1 | 1 | A list of the system boot images in the BOOT environment variable on supervisor modules with ROMMON. The format of sysBootVariabl… |
1.3.6.1.4.1.9.5.1.1.38 | sysBootedImage | 1 | 1 | The name of the system boot image which the system booted from. This MIB object is only supported in the system with Supervisor mo… |
1.3.6.1.4.1.9.5.1.1.39 | sysEnableEntityTrap | 1 | 1 | Indicates whether entConfigChange trap in the ENTITY-MIB should be generated. |
1.3.6.1.4.1.9.5.1.1.40 | sysEnableStpxTrap | 1 | 1 | Indicates whether stpxInconsistencyUpdate and stpxRootInconsistencyUpdate traps in the CISCO-STP-EXTENSIONS-MIB should be generat… |
1.3.6.1.4.1.9.5.1.1.41 | sysExtendedRmonVlanModeEnable | 1 | 1 | Indicates whether the Extended RMON VlanMode feature is enabled or not. If it is set to enabled(1), hostTable (rmon 4) will provi… |
1.3.6.1.4.1.9.5.1.1.42 | sysExtendedRmonNetflowPassword | 1 | 1 | The password for enabling the Extended RMON Netflow feature and this object has to be set before setting sysExtendedRmonNetflowEn… |
1.3.6.1.4.1.9.5.1.1.43 | sysExtendedRmonNetflowEnable | 1 | 1 | Indicates whether the Extended RMON Netflow feature is enabled or not. Setting this object to disabled(2), will clear sysExtendedR… |
1.3.6.1.4.1.9.5.1.1.44 | sysExtendedRmonVlanAgentEnable | 1 | 1 | Indicates whether the Extended RMON VlanAgent feature is enabled or not. If it is set to enabled(1), the extended RMON will also … |
1.3.6.1.4.1.9.5.1.1.45 | sysExtendedRmonEnable | 1 | 1 | Indicates whether the SNMP agent supports the extended RMON feature. noNAMPresent(3) is a read-only value and the agent will retu… |
1.3.6.1.4.1.9.5.1.1.46 | sysConsolePrimaryLoginAuthentication | 1 | 1 | Indicates whether TACACS+ or RADIUS is the primary login authentication, i.e which method will be tried first for a console sessi… |
1.3.6.1.4.1.9.5.1.1.47 | sysConsolePrimaryEnableAuthentication | 1 | 1 | Indicates whether TACACS+ or RADIUS is the primary enable authentication, i.e which method will be tried first for a console ses… |
1.3.6.1.4.1.9.5.1.1.48 | sysTelnetPrimaryLoginAuthentication | 1 | 1 | Indicates whether TACACS+ or RADIUS is the primary login authentication, i.e which method will be tried first for a telnet sessi… |
1.3.6.1.4.1.9.5.1.1.49 | sysTelnetPrimaryEnableAuthentication | 1 | 1 | Indicates whether TACACS+ or RADIUS is the primary enable authentication, i.e which method will be tried first for a telnet sessi… |
1.3.6.1.4.1.9.5.1.1.50 | sysStartupConfigSource | 1 | 1 | Indicates whether the configuration file(s) specified in sysStartupConfigSourceFile will be used recurringly or not whenever the … |
1.3.6.1.4.1.9.5.1.1.51 | sysStartupConfigSourceFile | 1 | 1 | Indicates which configuration file(s) on the flash device will be used during the next system startup. If the value of this MIB ob… |
1.3.6.1.4.1.9.5.1.1.52 | sysConfigSupervisorModuleNo | 1 | 1 | Indicates the supervisor module (active or standby, if applicable) that the MIB objects sysConfigRegister, sysBootVariable, sysSta… |
1.3.6.1.4.1.9.5.1.1.53 | sysStandbyPortEnable | 1 | 1 | Indicates whether the standby port feature is enabled or not. If this object is set to enabled(1), the uplink ports on the standb… |
1.3.6.1.4.1.9.5.1.1.54 | sysPortFastBpduGuard | 1 | 1 | Indicates whether BPDU Guard for Spanning Tree Port Fast Start feature is enabled or not. If the value of this object is set to e… |
1.3.6.1.4.1.9.5.1.1.55 | sysErrDisableTimeoutEnable | 1 | 1 | sysErrDisableTimeoutEnable OBJECT-TYPE SYNTAX BITS { other(0), udld(1), duplexMismatch(2), bpduPortGuard(3), channelMisconfig(4… |
1.3.6.1.4.1.9.5.1.1.56 | sysErrDisableTimeoutInterval | 1 | 1 | Indicates the timeout interval in seconds for errdisable timeout feature. |
1.3.6.1.4.1.9.5.1.1.57 | sysTrafficMonitorHighWaterMark | 1 | 1 | Indicates the high watermark for the switching bus traffic in percentage. Syslog messages will be generated if the switching bus … |
1.3.6.1.4.1.9.5.1.1.58 | sysHighAvailabilityEnable | 1 | 1 | Indicates whether High System Availability feature is enabled or not. If this feature is enabled, the active supervisor's layer-2… |
1.3.6.1.4.1.9.5.1.1.59 | sysHighAvailabilityVersioningEnable | 1 | 1 | Indicates whether support for supervisor software image versioning (i.e., the capability to run different images on the active an… |
1.3.6.1.4.1.9.5.1.1.60 | sysHighAvailabilityOperStatus | 1 | 1 | Indicates the operational status of High System Availability feature. If the value of this object is notRunning(2), then the reas… |
1.3.6.1.4.1.9.5.1.1.61 | sysHighAvailabilityNotRunningReason | 1 | 1 | Indicates the reason why High System Availability feature is not running when the value of sysHighAvailabilityOperStatus is notRu… |
1.3.6.1.4.1.9.5.1.1.62 | sysExtendedRmonNetflowModuleMask | 1 | 1 | Indicates Netflow Export Data (NDE) to be sent to which Network Analysis Modules (NAM) in the same chassis. If users set a bit fro… |
1.3.6.1.4.1.9.5.1.1.63 | sshPublicKeySize | 1 | 1 | Indicates public key size in bits. In write, if a key does not exist, a value between 512 and 2048 will generate a RSA public key… |
1.3.6.1.4.1.9.5.1.1.64 | sysMaxRmonMemory | 1 | 1 | Indicates the maximum percentage of the memory usage for RMON. |
1.3.6.1.4.1.9.5.1.1.65 | sysMacReductionAdminEnable | 1 | 1 | Indicates whether Mac Reduction feature (to reduce the number of MAC addresses used in bridge identifier) is administratively ena… |
1.3.6.1.4.1.9.5.1.1.66 | sysMacReductionOperEnable | 1 | 1 | Indicates whether Mac Reduction feature (to reduce the number of MAC addresses used in bridge identifier) is operationaly enabled… |
1.3.6.1.4.1.9.5.1.1.67 | sysStatus | 1 | 1 | The operational status of the system. |