This object is used to set a low alarm threshold on the
optical parameter being monitored.
An alarm condition will be raised if the value given by
cOpticalParameterValue goes from above the value configured in
this object to below the value configured in this object, or if
the initial value of cOpticalParameterValue is lower than the
value configured in this object. For network elements that
incorporate a soak time in the status indications, this alarm
will be indicated in the cOpticalParamAlarmStatus object only
after it persists for a period of time that equals the set soak
interval.
The severity level of this alarm is specified by the
cOpticalParamLowAlarmSev object.
When the cOpticalMonParameterType object is set to 'power'
for the receive direction and when the interface supports
alarms based on loss of light, this object specifies the
optical power threshold for declaring loss of light. Also,
when optical amplifiers are present in the network, in the
receive direction, this value may need to be configured,
since the noise floor may be higher than the minimum
sensitivity of the receiver.
Parsed from file CISCO-OPTICAL-MONITOR-MIB.mib
Module: CISCO-OPTICAL-MONITOR-MIB
This object is used to set a low alarm threshold on the
optical parameter being monitored.
An alarm condition will be raised if the value given by
cOpticalParameterValue goes from above the value configured in
this object to below the value configured in this object, or if
the initial value of cOpticalParameterValue is lower than the
value configured in this object. For network elements that
incorporate a soak time in the status indications, this alarm
will be indicated in the cOpticalParamAlarmStatus object only
after it persists for a period of time that equals the set soak
interval.
The severity level of this alarm is specified by the
cOpticalParamLowAlarmSev object.
When the cOpticalMonParameterType object is set to 'power'
for the receive direction and when the interface supports
alarms based on loss of light, this object specifies the
optical power threshold for declaring loss of light. Also,
when optical amplifiers are present in the network, in the
receive direction, this value may need to be configured,
since the noise floor may be higher than the minimum
sensitivity of the receiver.
This object is used to set a low alarm threshold on the
optical parameter being monitored.
An alarm condition will be raised if the value given by
cOpticalParameterValue goes from above the value configured in
this object to below the value configured in this object, or if
the initial value of cOpticalParameterValue is lower than the
value configured in this object. For network elements that
incorporate a soak time in the status indications, this alarm
will be indicated in the cOpticalParamAlarmStatus object only
after it persists for a period of time that equals the set soak
interval.
The severity level of this alarm is specified by the
cOpticalParamLowAlarmSev object.
When the cOpticalMonParameterType object is set to 'power'
for the receive direction and when the interface supports
alarms based on loss of light, this object specifies the
optical power threshold for declaring loss of light. Also,
when optical amplifiers are present in the network, in the
receive direction, this value may need to be configured,
since the noise floor may be higher than the minimum
sensitivity of the receiver.
Parsed from file CISCO-OPTICAL-MONITOR-MIB.my.txt
Company: None
Module: CISCO-OPTICAL-MONITOR-MIB
This object is used to set a low alarm threshold on the
optical parameter being monitored.
An alarm condition will be raised if the value given by
cOpticalParameterValue goes from above the value configured in
this object to below the value configured in this object, or if
the initial value of cOpticalParameterValue is lower than the
value configured in this object. For network elements that
incorporate a soak time in the status indications, this alarm
will be indicated in the cOpticalParamAlarmStatus object only
after it persists for a period of time that equals the set soak
interval.
The severity level of this alarm is specified by the
cOpticalParamLowAlarmSev object.
When the cOpticalMonParameterType object is set to 'power'
for the receive direction and when the interface supports
alarms based on loss of light, this object specifies the
optical power threshold for declaring loss of light. Also,
when optical amplifiers are present in the network, in the
receive direction, this value may need to be configured,
since the noise floor may be higher than the minimum
sensitivity of the receiver.
cOpticalParamLowAlarmThresh OBJECT-TYPE SYNTAX OpticalParameterValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to set a low alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by cOpticalParameterValue goes from above the value configured in this object to below the value configured in this object, or if the initial value of cOpticalParameterValue is lower than the value configured in this object. For network elements that incorporate a soak time in the status indications, this alarm will be indicated in the cOpticalParamAlarmStatus object only after it persists for a period of time that equals the set soak interval. The severity level of this alarm is specified by the cOpticalParamLowAlarmSev object. When the cOpticalMonParameterType object is set to 'power' for the receive direction and when the interface supports alarms based on loss of light, this object specifies the optical power threshold for declaring loss of light. Also, when optical amplifiers are present in the network, in the receive direction, this value may need to be configured, since the noise floor may be higher than the minimum sensitivity of the receiver." ::= { cOpticalMonEntry 9 }
cOpticalParamLowAlarmThresh OBJECT-TYPE SYNTAX OpticalParameterValue ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to set a low alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by cOpticalParameterValue goes from above the value configured in this object to below the value configured in this object, or if the initial value of cOpticalParameterValue is lower than the value configured in this object. For network elements that incorporate a soak time in the status indications, this alarm will be indicated in the cOpticalParamAlarmStatus object only after it persists for a period of time that equals the set soak interval. The severity level of this alarm is specified by the cOpticalParamLowAlarmSev object. When the cOpticalMonParameterType object is set to 'power' for the receive direction and when the interface supports alarms based on loss of light, this object specifies the optical power threshold for declaring loss of light. Also, when optical amplifiers are present in the network, in the receive direction, this value may need to be configured, since the noise floor may be higher than the minimum sensitivity of the receiver." ::= { cOpticalMonEntry 9 }
Vendor: Cisco
Module: CISCO-OPTICAL-MONITOR-MIB
[Automatically extracted from oidview.com]
cOpticalParamLowAlarmThresh OBJECT-TYPE SYNTAX OpticalParameterValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to set a low alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by cOpticalParameterValue goes from above the value configured in this object to below the value configured in this object, or if the initial value of cOpticalParameterValue is lower than the value configured in this object. For network elements that incorporate a soak time in the status indications, this alarm will be indicated in the cOpticalParamAlarmStatus object only after it persists for a period of time that equals the set soak interval. The severity level of this alarm is specified by the cOpticalParamLowAlarmSev object. When the cOpticalMonParameterType object is set to 'power' for the receive direction and when the interface supports alarms based on loss of light, this object specifies the optical power threshold for declaring loss of light. Also, when optical amplifiers are present in the network, in the receive direction, this value may need to be configured, since the noise floor may be higher than the minimum sensitivity of the receiver." ::= { cOpticalMonEntry 9 }
cOpticalParamLowAlarmThresh OBJECT-TYPE SYNTAX OpticalParameterValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to set a low alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by cOpticalParameterValue goes from above the value configured in this object to below the value configured in this object, or if the initial value of cOpticalParameterValue is lower than the value configured in this object. For network elements that incorporate a soak time in the status indications, this alarm will be indicated in the cOpticalParamAlarmStatus object only after it persists for a period of time that equals the set soak interval. The severity level of this alarm is specified by the cOpticalParamLowAlarmSev object. When the cOpticalMonParameterType object is set to 'power' for the receive direction and when the interface supports alarms based on loss of light, this object specifies the optical power threshold for declaring loss of light. Also, when optical amplifiers are present in the network, in the receive direction, this value may need to be configured, since the noise floor may be higher than the minimum sensitivity of the receiver." ::= { cOpticalMonEntry 9 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.264.1.1.1.1.1 | cOpticalMonDirection | 0 | 0 | This object indicates the direction monitored for the optical interface, in this entry. |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.2 | cOpticalMonLocation | 0 | 0 | This object indicates whether the optical characteristics are measured before or after adjustment (e.g. optical amplification or … |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.3 | cOpticalMonParameterType | 0 | 0 | This object specifies the optical parameter that is being monitored in this entry. |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.4 | cOpticalParameterValue | 0 | 0 | This object gives the value measured for the particular optical parameter specified by the cOpticalMonParameterType object. |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.5 | cOpticalParamHighAlarmThresh | 0 | 0 | This object is used to set a high alarm threshold on the optical parameter being monitored. An alarm condition will be raised if … |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.6 | cOpticalParamHighAlarmSev | 0 | 0 | This object is used to specify a severity level associated with the high alarm threshold given by the cOpticalParamHighAlarmThres… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.7 | cOpticalParamHighWarningThresh | 0 | 0 | This object is used to set a high warning threshold on the optical parameter being monitored. A threshold crossing condition will… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.8 | cOpticalParamHighWarningSev | 0 | 0 | This object is used to specify a severity level associated with the high warning threshold given by the cOpticalParamHighWarningT… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.10 | cOpticalParamLowAlarmSev | 0 | 0 | This object is used to specify a severity level associated with the low alarm threshold given by the cOpticalParamLowAlarmThresh … |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.11 | cOpticalParamLowWarningThresh | 0 | 0 | This object is used to set a low warning threshold on the optical parameter being monitored. A threshold crossing condition will … |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.12 | cOpticalParamLowWarningSev | 0 | 0 | This object is used to specify a severity level associated with the low warning threshold given by the cOpticalParamLowWarningThr… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.13 | cOpticalParamAlarmStatus | 0 | 0 | This object is used to indicate the current status of the thresholds for the monitored optical parameter on the interface. If a th… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.14 | cOpticalParamAlarmCurMaxThresh | 0 | 0 | This object indicates the threshold value of the highest severity threshold that is currently being exceeded on the interface, fo… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.15 | cOpticalParamAlarmCurMaxSev | 0 | 0 | This object indicates the maximum severity of any thresholds that are currently being exceeded on the interface, for the optical … |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.16 | cOpticalParamAlarmLastChange | 0 | 0 | This object specifies the value of sysUpTime at the last time a threshold related to a particular optical parameter was exceeded … |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.17 | cOpticalMon15MinValidIntervals | 0 | 0 | This object gives the number of previous 15 minute intervals for which valid performance monitoring data has been stored on the i… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.18 | cOpticalMon24HrValidIntervals | 0 | 0 | This object gives the number of previous 24 hour intervals for which valid performance monitoring data has been stored on the int… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.19 | cOpticalParamThreshSource | 0 | 0 | This object indicates if the current value of a particular threshold in this entry is user configured value or it is a system def… |