Point in network where last loopback was performed.
Meaning for t1 CSU/DSU:
dtePayload - local DSU loopback. The configured 'fractions'
of the DS1 signal is looped back as the receive signal.
Used to verify operation of DSU portion of local
CSU/DSU.
dteFull - local CSU loopback. DS1 transmit signal is looped
back as the receive signal. Runs at full bandwidth
irrespective of fractions configured. Used to verify
operation of local CSU/DSU.
lineFull - DS1 signal received from the network is transmitted
back to the network. Signal is regenerated but not
reframed. Loopback performed at the CSU. Used to
verify operation of T1 network.
linePayload - DS1 signal received from the network is
transmitted back to the network. Data is regenerated
and reframed with any LCV or CRC errors corrected.
Loopback performed at the DSU. Used to verify
operation of local CSU/DSU and T1 network.
remoteSmartJack - the remote smart jack (telco installed wall
socket device used to delineate network between CPE and
telco equipment) is used to loopback the DS1 signal.
Similar to remoteFull loopback except that the signal
is looped at the smart jack before reaching remote
CSU/DSU. Used to verify operation of local CSU/DSU
and T1 network.
remoteFull - remote unit placed in lineFull loopback.
Used to verify operation of local CSU/DSU and T1
network.
remotePayload - remote unit placed in linePayload loopback
Used to verify operation of local CSU/DSU, T1 network,
and remote CSU/DSU.
Meaning for switched 56k CSU/DSU:
dteFull - local CSU loopback. Transmit signal is looped back
as the receive signal at a point close to the physical
network interface. Used to verify operation of local
CSU/DSU.
lineFull - CSU/DSU is split into separate DTE and loop
interface sections. Signal received from the network
is transmitted back to the network. Data received
from DTE is transmitted back to DTE. Used to verify
operation of local CSU/DSU and network from remote site.
linePayload - Signal received from the network is looped
back at the DTE interface and transmitted back to the
network. Data received from DTE is ignored. Used to
verify operation of local CSU/DSU and network from
remote site.
remotePayload - Similar to linePayload except that the
remote unit is placed into loopback. Used to verify
operation of local CSU/DSU, T1 network, and remote
CSU/DSU.
Parsed from file CISCO-ICSUDSU-MIB.mib
Module: CISCO-ICSUDSU-MIB
Point in network where last loopback was performed.
Meaning for t1 CSU/DSU:
dtePayload - local DSU loopback. The configured 'fractions'
of the DS1 signal is looped back as the receive signal.
Used to verify operation of DSU portion of local
CSU/DSU.
dteFull - local CSU loopback. DS1 transmit signal is looped
back as the receive signal. Runs at full bandwidth
irrespective of fractions configured. Used to verify
operation of local CSU/DSU.
lineFull - DS1 signal received from the network is transmitted
back to the network. Signal is regenerated but not
reframed. Loopback performed at the CSU. Used to
verify operation of T1 network.
linePayload - DS1 signal received from the network is
transmitted back to the network. Data is regenerated
and reframed with any LCV or CRC errors corrected.
Loopback performed at the DSU. Used to verify
operation of local CSU/DSU and T1 network.
remoteSmartJack - the remote smart jack (telco installed wall
socket device used to delineate network between CPE and
telco equipment) is used to loopback the DS1 signal.
Similar to remoteFull loopback except that the signal
is looped at the smart jack before reaching remote
CSU/DSU. Used to verify operation of local CSU/DSU
and T1 network.
remoteFull - remote unit placed in lineFull loopback.
Used to verify operation of local CSU/DSU and T1
network.
remotePayload - remote unit placed in linePayload loopback
Used to verify operation of local CSU/DSU, T1 network,
and remote CSU/DSU.
Meaning for switched 56k CSU/DSU:
dteFull - local CSU loopback. Transmit signal is looped back
as the receive signal at a point close to the physical
network interface. Used to verify operation of local
CSU/DSU.
lineFull - CSU/DSU is split into separate DTE and loop
interface sections. Signal received from the network
is transmitted back to the network. Data received
from DTE is transmitted back to DTE. Used to verify
operation of local CSU/DSU and network from remote site.
linePayload - Signal received from the network is looped
back at the DTE interface and transmitted back to the
network. Data received from DTE is ignored. Used to
verify operation of local CSU/DSU and network from
remote site.
remotePayload - Similar to linePayload except that the
remote unit is placed into loopback. Used to verify
operation of local CSU/DSU, T1 network, and remote
CSU/DSU.
ciscoICsuDsuLoopbackPoint OBJECT-TYPE
SYNTAX INTEGER {
dtePayload (1),
dteFull (2),
lineFull (3),
linePayload (4),
remoteSmartJack (5),
remoteFull (6),
remotePayload (7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Point in network where last loopback was performed.
Meaning for t1 CSU/DSU:
dtePayload - local DSU loopback. The configured
ractions
of the DS1 signal is looped back as the receive signal.
Used to verify operation of DSU portion of local
CSU/DSU.
dteFull - local CSU loopback. DS1 transmit signal is looped
back as the receive signal. Runs at full bandwidth
irrespective of fractions configured. Used to verify
operation of local CSU/DSU.
lineFull - DS1 signal received from the network is transmitted
back to the network. Signal is regenerated but not
reframed. Loopback performed at the CSU. Used to
verify operation of T1 network.
linePayload - DS1 signal received from the network is
transmitted back to the network. Data is regenerated
and reframed with any LCV or CRC errors corrected.
Loopback performed at the DSU. Used to verify
operation of local CSU/DSU and T1 network.
remoteSmartJack - the remote smart jack (telco installed wall
socket device used to delineate network between CPE and
telco equipment) is used to loopback the DS1 signal.
Similar to remoteFull loopback except that the signal
is looped at the smart jack before reaching remote
CSU/DSU. Used to verify operation of local CSU/DSU
and T1 network.
remoteFull - remote unit placed in lineFull loopback.
Used to verify operation of local CSU/DSU and T1
network.
remotePayload - remote unit placed in linePayload loopback
Used to verify operation of local CSU/DSU, T1 network,
and remote CSU/DSU.
Meaning for switched 56k CSU/DSU:
dteFull - local CSU loopback. Transmit signal is looped back
as the receive signal at a point close to the physical
network interface. Used to verify operation of local
CSU/DSU.
lineFull - CSU/DSU is split into separate DTE and loop
interface sections. Signal received from the network
is transmitted back to the network. Data received
from DTE is transmitted back to DTE. Used to verify
operation of local CSU/DSU and network from remote site.
linePayload - Signal received from the network is looped
back at the DTE interface and transmitted back to the
network. Data received from DTE is ignored. Used to
verify operation of local CSU/DSU and network from
remote site.
remotePayload - Similar to linePayload except that the
remote unit is placed into loopback. Used to verify
operation of local CSU/DSU, T1 network, and remote
CSU/DSU.
"
View at oid-info.com
Point in network where last loopback was performed.
Meaning for t1 CSU/DSU:
dtePayload - local DSU loopback. The configured 'fractions'
of the DS1 signal is looped back as the receive signal.
Used to verify operation of DSU portion of local
CSU/DSU.
dteFull - local CSU loopback. DS1 transmit signal is looped
back as the receive signal. Runs at full bandwidth
irrespective of fractions configured. Used to verify
operation of local CSU/DSU.
lineFull - DS1 signal received from the network is transmitted
back to the network. Signal is regenerated but not
reframed. Loopback performed at the CSU. Used to
verify operation of T1 network.
linePayload - DS1 signal received from the network is
transmitted back to the network. Data is regenerated
and reframed with any LCV or CRC errors corrected.
Loopback performed at the DSU. Used to verify
operation of local CSU/DSU and T1 network.
remoteSmartJack - the remote smart jack (telco installed wall
socket device used to delineate network between CPE and
telco equipment) is used to loopback the DS1 signal.
Similar to remoteFull loopback except that the signal
is looped at the smart jack before reaching remote
CSU/DSU. Used to verify operation of local CSU/DSU
and T1 network.
remoteFull - remote unit placed in lineFull loopback.
Used to verify operation of local CSU/DSU and T1
network.
remotePayload - remote unit placed in linePayload loopback
Used to verify operation of local CSU/DSU, T1 network,
and remote CSU/DSU.
Meaning for switched 56k CSU/DSU:
dteFull - local CSU loopback. Transmit signal is looped back
as the receive signal at a point close to the physical
network interface. Used to verify operation of local
CSU/DSU.
lineFull - CSU/DSU is split into separate DTE and loop
interface sections. Signal received from the network
is transmitted back to the network. Data received
from DTE is transmitted back to DTE. Used to verify
operation of local CSU/DSU and network from remote site.
linePayload - Signal received from the network is looped
back at the DTE interface and transmitted back to the
network. Data received from DTE is ignored. Used to
verify operation of local CSU/DSU and network from
remote site.
remotePayload - Similar to linePayload except that the
remote unit is placed into loopback. Used to verify
operation of local CSU/DSU, T1 network, and remote
CSU/DSU.
Parsed from file CISCO-ICSUDSU-MIB.my.txt
Company: None
Module: CISCO-ICSUDSU-MIB
Point in network where last loopback was performed.
Meaning for t1 CSU/DSU:
dtePayload - local DSU loopback. The configured 'fractions'
of the DS1 signal is looped back as the receive signal.
Used to verify operation of DSU portion of local
CSU/DSU.
dteFull - local CSU loopback. DS1 transmit signal is looped
back as the receive signal. Runs at full bandwidth
irrespective of fractions configured. Used to verify
operation of local CSU/DSU.
lineFull - DS1 signal received from the network is transmitted
back to the network. Signal is regenerated but not
reframed. Loopback performed at the CSU. Used to
verify operation of T1 network.
linePayload - DS1 signal received from the network is
transmitted back to the network. Data is regenerated
and reframed with any LCV or CRC errors corrected.
Loopback performed at the DSU. Used to verify
operation of local CSU/DSU and T1 network.
remoteSmartJack - the remote smart jack (telco installed wall
socket device used to delineate network between CPE and
telco equipment) is used to loopback the DS1 signal.
Similar to remoteFull loopback except that the signal
is looped at the smart jack before reaching remote
CSU/DSU. Used to verify operation of local CSU/DSU
and T1 network.
remoteFull - remote unit placed in lineFull loopback.
Used to verify operation of local CSU/DSU and T1
network.
remotePayload - remote unit placed in linePayload loopback
Used to verify operation of local CSU/DSU, T1 network,
and remote CSU/DSU.
Meaning for switched 56k CSU/DSU:
dteFull - local CSU loopback. Transmit signal is looped back
as the receive signal at a point close to the physical
network interface. Used to verify operation of local
CSU/DSU.
lineFull - CSU/DSU is split into separate DTE and loop
interface sections. Signal received from the network
is transmitted back to the network. Data received
from DTE is transmitted back to DTE. Used to verify
operation of local CSU/DSU and network from remote site.
linePayload - Signal received from the network is looped
back at the DTE interface and transmitted back to the
network. Data received from DTE is ignored. Used to
verify operation of local CSU/DSU and network from
remote site.
remotePayload - Similar to linePayload except that the
remote unit is placed into loopback. Used to verify
operation of local CSU/DSU, T1 network, and remote
CSU/DSU.
ciscoICsuDsuLoopbackPoint OBJECT-TYPE SYNTAX INTEGER { dtePayload (1), dteFull (2), lineFull (3), linePayload (4), remoteSmartJack (5), remoteFull (6), remotePayload (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Point in network where last loopback was performed. Meaning for t1 CSU/DSU: dtePayload - local DSU loopback. The configured 'fractions' of the DS1 signal is looped back as the receive signal. Used to verify operation of DSU portion of local CSU/DSU. dteFull - local CSU loopback. DS1 transmit signal is looped back as the receive signal. Runs at full bandwidth irrespective of fractions configured. Used to verify operation of local CSU/DSU. lineFull - DS1 signal received from the network is transmitted back to the network. Signal is regenerated but not reframed. Loopback performed at the CSU. Used to verify operation of T1 network. linePayload - DS1 signal received from the network is transmitted back to the network. Data is regenerated and reframed with any LCV or CRC errors corrected. Loopback performed at the DSU. Used to verify operation of local CSU/DSU and T1 network. remoteSmartJack - the remote smart jack (telco installed wall socket device used to delineate network between CPE and telco equipment) is used to loopback the DS1 signal. Similar to remoteFull loopback except that the signal is looped at the smart jack before reaching remote CSU/DSU. Used to verify operation of local CSU/DSU and T1 network. remoteFull - remote unit placed in lineFull loopback. Used to verify operation of local CSU/DSU and T1 network. remotePayload - remote unit placed in linePayload loopback Used to verify operation of local CSU/DSU, T1 network, and remote CSU/DSU. Meaning for switched 56k CSU/DSU: dteFull - local CSU loopback. Transmit signal is looped back as the receive signal at a point close to the physical network interface. Used to verify operation of local CSU/DSU. lineFull - CSU/DSU is split into separate DTE and loop interface sections. Signal received from the network is transmitted back to the network. Data received from DTE is transmitted back to DTE. Used to verify operation of local CSU/DSU and network from remote site. linePayload - Signal received from the network is looped back at the DTE interface and transmitted back to the network. Data received from DTE is ignored. Used to verify operation of local CSU/DSU and network from remote site. remotePayload - Similar to linePayload except that the remote unit is placed into loopback. Used to verify operation of local CSU/DSU, T1 network, and remote CSU/DSU. " ::= { ciscoICsuDsuTestReportEntry 8 }
ciscoICsuDsuLoopbackPoint OBJECT-TYPE SYNTAX INTEGER { dtePayload(1), dteFull(2), lineFull(3), linePayload(4), remoteSmartJack(5), remoteFull(6), remotePayload(7) } ACCESS read-only STATUS mandatory DESCRIPTION "Point in network where last loopback was performed. Meaning for t1 CSU/DSU: dtePayload - local DSU loopback. The configured 'fractions' of the DS1 signal is looped back as the receive signal. Used to verify operation of DSU portion of local CSU/DSU. dteFull - local CSU loopback. DS1 transmit signal is looped back as the receive signal. Runs at full bandwidth irrespective of fractions configured. Used to verify operation of local CSU/DSU. lineFull - DS1 signal received from the network is transmitted back to the network. Signal is regenerated but not reframed. Loopback performed at the CSU. Used to verify operation of T1 network. linePayload - DS1 signal received from the network is transmitted back to the network. Data is regenerated and reframed with any LCV or CRC errors corrected. Loopback performed at the DSU. Used to verify operation of local CSU/DSU and T1 network. remoteSmartJack - the remote smart jack (telco installed wall socket device used to delineate network between CPE and telco equipment) is used to loopback the DS1 signal. Similar to remoteFull loopback except that the signal is looped at the smart jack before reaching remote CSU/DSU. Used to verify operation of local CSU/DSU and T1 network. remoteFull - remote unit placed in lineFull loopback. Used to verify operation of local CSU/DSU and T1 network. remotePayload - remote unit placed in linePayload loopback Used to verify operation of local CSU/DSU, T1 network, and remote CSU/DSU. Meaning for switched 56k CSU/DSU: dteFull - local CSU loopback. Transmit signal is looped back as the receive signal at a point close to the physical network interface. Used to verify operation of local CSU/DSU. lineFull - CSU/DSU is split into separate DTE and loop interface sections. Signal received from the network is transmitted back to the network. Data received from DTE is transmitted back to DTE. Used to verify operation of local CSU/DSU and network from remote site. linePayload - Signal received from the network is looped back at the DTE interface and transmitted back to the network. Data received from DTE is ignored. Used to verify operation of local CSU/DSU and network from remote site. remotePayload - Similar to linePayload except that the remote unit is placed into loopback. Used to verify operation of local CSU/DSU, T1 network, and remote CSU/DSU. " ::= { ciscoICsuDsuTestReportEntry 8 }
Automatically extracted from Cisco "SNMP v2 MIBs".
ciscoICsuDsuLoopbackPoint OBJECT-TYPE SYNTAX INTEGER { dtePayload (1), dteFull (2), lineFull (3), linePayload (4), remoteSmartJack (5), remoteFull (6), remotePayload (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Point in network where last loopback was performed. Meaning for t1 CSU/DSU: dtePayload - local DSU loopback. The configured 'fractions' of the DS1 signal is looped back as the receive signal. Used to verify operation of DSU portion of local CSU/DSU. dteFull - local CSU loopback. DS1 transmit signal is looped back as the receive signal. Runs at full bandwidth irrespective of fractions configured. Used to verify operation of local CSU/DSU. lineFull - DS1 signal received from the network is transmitted back to the network. Signal is regenerated but not reframed. Loopback performed at the CSU. Used to verify operation of T1 network. linePayload - DS1 signal received from the network is transmitted back to the network. Data is regenerated and reframed with any LCV or CRC errors corrected. Loopback performed at the DSU. Used to verify operation of local CSU/DSU and T1 network. remoteSmartJack - the remote smart jack (telco installed wall socket device used to delineate network between CPE and telco equipment) is used to loopback the DS1 signal. Similar to remoteFull loopback except that the signal is looped at the smart jack before reaching remote CSU/DSU. Used to verify operation of local CSU/DSU and T1 network. remoteFull - remote unit placed in lineFull loopback. Used to verify operation of local CSU/DSU and T1 network. remotePayload - remote unit placed in linePayload loopback Used to verify operation of local CSU/DSU, T1 network, and remote CSU/DSU. Meaning for switched 56k CSU/DSU: dteFull - local CSU loopback. Transmit signal is looped back as the receive signal at a point close to the physical network interface. Used to verify operation of local CSU/DSU. lineFull - CSU/DSU is split into separate DTE and loop interface sections. Signal received from the network is transmitted back to the network. Data received from DTE is transmitted back to DTE. Used to verify operation of local CSU/DSU and network from remote site. linePayload - Signal received from the network is looped back at the DTE interface and transmitted back to the network. Data received from DTE is ignored. Used to verify operation of local CSU/DSU and network from remote site. remotePayload - Similar to linePayload except that the remote unit is placed into loopback. Used to verify operation of local CSU/DSU, T1 network, and remote CSU/DSU. " ::= { ciscoICsuDsuTestReportEntry 8 }
ciscoICsuDsuLoopbackPoint OBJECT-TYPE SYNTAX INTEGER { dtePayload (1), dteFull (2), lineFull (3), linePayload (4), remoteSmartJack (5), remoteFull (6), remotePayload (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Point in network where last loopback was performed. Meaning for t1 CSU/DSU: dtePayload - local DSU loopback. The configured 'fractions' of the DS1 signal is looped back as the receive signal. Used to verify operation of DSU portion of local CSU/DSU. dteFull - local CSU loopback. DS1 transmit signal is looped back as the receive signal. Runs at full bandwidth irrespective of fractions configured. Used to verify operation of local CSU/DSU. lineFull - DS1 signal received from the network is transmitted back to the network. Signal is regenerated but not reframed. Loopback performed at the CSU. Used to verify operation of T1 network. linePayload - DS1 signal received from the network is transmitted back to the network. Data is regenerated and reframed with any LCV or CRC errors corrected. Loopback performed at the DSU. Used to verify operation of local CSU/DSU and T1 network. remoteSmartJack - the remote smart jack (telco installed wall socket device used to delineate network between CPE and telco equipment) is used to loopback the DS1 signal. Similar to remoteFull loopback except that the signal is looped at the smart jack before reaching remote CSU/DSU. Used to verify operation of local CSU/DSU and T1 network. remoteFull - remote unit placed in lineFull loopback. Used to verify operation of local CSU/DSU and T1 network. remotePayload - remote unit placed in linePayload loopback Used to verify operation of local CSU/DSU, T1 network, and remote CSU/DSU. Meaning for switched 56k CSU/DSU: dteFull - local CSU loopback. Transmit signal is looped back as the receive signal at a point close to the physical network interface. Used to verify operation of local CSU/DSU. lineFull - CSU/DSU is split into separate DTE and loop interface sections. Signal received from the network is transmitted back to the network. Data received from DTE is transmitted back to DTE. Used to verify operation of local CSU/DSU and network from remote site. linePayload - Signal received from the network is looped back at the DTE interface and transmitted back to the network. Data received from DTE is ignored. Used to verify operation of local CSU/DSU and network from remote site. remotePayload - Similar to linePayload except that the remote unit is placed into loopback. Used to verify operation of local CSU/DSU, T1 network, and remote CSU/DSU. " ::= { ciscoICsuDsuTestReportEntry 8 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.9.9.44.1.1.2.1.1 | ciscoICsuDsuLastSelfTestResult | 0 | 0 | ciscoICsuDsuLastSelftestResult |
1.3.6.1.4.1.9.9.44.1.1.2.1.2 | ciscoICsuDsuTimeOfLastSelfTest | 0 | 0 | SysUpTime of LastSelfTest execution. |
1.3.6.1.4.1.9.9.44.1.1.2.1.3 | ciscoICsuDsuNumResets | 0 | 0 | Number of times CSU/DSU has been reset. |
1.3.6.1.4.1.9.9.44.1.1.2.1.4 | ciscoICsuDsuTimeOfLastReset | 0 | 0 | SysUpTime of last CSU/DSU reset. |
1.3.6.1.4.1.9.9.44.1.1.2.1.5 | ciscoICsuDsuLoopbackStatus | 0 | 0 | Current Status of Loopback. Remaining Loopback results are valid only if status is 'completed' or 'failed' or 'noSyncWithTestPat… |
1.3.6.1.4.1.9.9.44.1.1.2.1.6 | ciscoICsuDsuLoopbackNumErrors | 0 | 0 | Number of Bit errors that occurred in last successful loopback test. Valid only if remote loopback with pattern was performed an… |
1.3.6.1.4.1.9.9.44.1.1.2.1.7 | ciscoICsuDsuLoopbackDuration | 0 | 0 | Duration of last successful loopback test in hundredths of seconds. Note that it is possible for the CSU/DSU to lose framing dur… |
1.3.6.1.4.1.9.9.44.1.1.2.1.9 | ciscoICsuDsuLoopbackPattern | 0 | 0 | ciscoICsuDsuLoopbackPattern OBJECT-TYPE SYNTAX INTEGER { noPattern (1), patternQRW (2), pattern0In1 (3), pattern1In1 (4), patte… |
1.3.6.1.4.1.9.9.44.1.1.2.1.10 | ciscoICsuDsuUserDefinedPattern | 0 | 0 | User Defined Loopback Pattern. Valid only if ciscoICsuDsuLoopbackPattern is patternUser. |
1.3.6.1.4.1.9.9.44.1.1.2.1.11 | ciscoICsuDsuLoopbackCode | 0 | 0 | LoopCode used to initiate last remote loopback. Valid only if a only if a remote loopback was last performed. standard - standar… |
1.3.6.1.4.1.9.9.44.1.1.2.1.12 | ciscoICsuDsuEndTimeOfLastLoopback | 0 | 0 | SysUpTime of completion of last loopback test execution. |