Vendor: Hewlett-Packard
Module: HP-LASERJET-COMMON-MIB
[Automatically extracted from oidview.com]
settings-prt-eng OBJECT IDENTIFIER ::= { print-engine 1 }
settings-prt-eng OBJECT IDENTIFIER ::= { print-engine 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.2 | override-media-name | 1 | 1 | Sets a string identifying the media name that is to be used in place of the currently requested media. The substitution will con… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.3 | override-media-size | 1 | 1 | Sets the media size that is to be used in place of the currently requested media size. Additional information: When a request is r… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.4 | default-duplex-mode | 1 | 1 | Returns or sets the duplex printing mode. Duplex printing is when printing occurs on both sides of a sheet of media. Vertical b… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.5 | print-density | 1 | 1 | Returns or sets the print density setting. Print density is the instantaneous amount of marking agent applied to the paper while… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.8 | transfer-setting | 1 | 1 | When set the object will cause the transfer setting of the device to be changed to the nearest appropriate value. When the object… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.9 | marking-agent-density | 1 | 2 | None |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.10 | autocleaning-page-enable | 1 | 1 | When set to eEnabled this object will enable the periodic printing of a page designed to clean the fuser on an EP printing system… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.11 | autocleaning-page-frequency | 1 | 1 | Controls the number of pages between printing of the auto cleaning page (if enabled). Any device specific 'snap' behavior for th… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.12 | autocleaning-page-size | 1 | 1 | Controls the size of paper used to print the auto cleaning page (if enabled). Additional information: For the LaserJet 4100mfp pro… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.13 | separation-setting | 1 | 1 | When set this object will cause the separation setting of the device to be changed to the nearest appropriate value. When the obj… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.24 | configurable-low-threshold-setting | 0 | 0 | This PML object can be used to configure the low threshold for supplies. Additional information: This PML object can be used to co… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.25 | supplies-replace-action-at-setting | 0 | 0 | This object can be used to change the setting of menu item REPLACE SUPPLIES. The behavior of the printer when a supply reaches lo… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.27 | cartridge-out-override-control | 0 | 0 | This PML object is used to control Cartridge Out Override feature. Additional information: This object is used for the following p… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.28 | duplex-blank-pages, override-media-name | 0 | 0 | Sets a string identifying the media name that is to be used inplace of the currently requested media. The substitution willcont… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.31 | finisher-image-rotation | 0 | 0 | This PML object will provide the additional image rotation thatis applied to a printed job depending on the presence orabsence … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.36 | cartridge-adaptive-gain | 0 | 0 | The Adaptive TA Gain is stored for the last 5 cartridges.Cartridge one is the most recent to be installed (current), andcartrid… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.37 | cartridge-adaptive-gain-reset, override-media-size | 0 | 0 | This object will Reset the Adaptive TA Gain value to 1.00 anddisable the adaptive TA routine. The value that this objectreturns… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.38 | supplies-at-very-low-setting | 0 | 0 | This object can be used to change the setting of menu item ATVERY LOW. The behavior of the printer when a supply reaches lowcha… |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2 | status-prt-eng | 15 | 35 | None |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3 | intray | 3 | 93 | None |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4 | outbin | 2 | 102 | None |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5 | marking-agent | 1 | 7 | None |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.6 | imaging, default-ret, default-print-quality | 2 | 4 | Returns or changes the Resolution Enhancement Technologysetting. Devices that only support eOff and eOn should map allother val… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7 | ph | 2 | 28 | None |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8 | print-media | 7 | 269 | None |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.9 | print-engine-test | 5 | 25 | None |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10 | consumables | 11 | 138 | None |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.11 | print-meter | 1 | 11 | None |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.13 | menus | 0 | 0 | None |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.15 | media-sizes, media-size-supported-driver-n-string | 1 | 1 | Returns the Driver (PJL) string used to specigy a media size,for each media size that is supported by a product. PML walk of1.4… |