| 1.3.6.1.4.1.15.2.3.7.1.1 |
anxpPortIndex, portIndex | 0 | 0 |
A unique number from 1 to totalPorts that
identifies each serial port. |
| 1.3.6.1.4.1.15.2.3.7.1.2 |
anxpMode, iSpeed | 0 | 0 |
This parameter defines the mode for access to
the serial line port. The default is cli |
| 1.3.6.1.4.1.15.2.3.7.1.3 |
anxpCtrlLines, oSpeed | 0 | 0 |
The type of hardware control used on the port:
modem control (dcddtr), flow control (ctsrts),
or both. |
| 1.3.6.1.4.1.15.2.3.7.1.4 |
anxpBidirModem, ctrlLines | 0 | 0 |
This parameter controls whether the port is
configured for adaptive use with a bidirectional
modem. |
| 1.3.6.1.4.1.15.2.3.7.1.5 |
anxpAllowBcast, flowTypeIn | 0 | 0 |
Controls whether the serial port can receive
administrative broadcast messages. |
| 1.3.6.1.4.1.15.2.3.7.1.6 |
anxpBcastDirection, flowTypeOut | 0 | 0 |
Defines the direction that an administrative
broadcast message is sent. This parameter is
valid only when the port is defined as… |
| 1.3.6.1.4.1.15.2.3.7.1.7 |
anxpInputStartChar, bitsPerChar | 0 | 0 |
The control character sequence that restarts
input if the charPortInFlowType parameter
(in the char MIB) is set to xonXoff. |
| 1.3.6.1.4.1.15.2.3.7.1.8 |
anxpInputStopChar, stopBits | 0 | 0 |
The control character sequence that stops
input if the charPortInFlowType parameter
(in the char MIB) is set to xonXoff. |
| 1.3.6.1.4.1.15.2.3.7.1.9 |
anxpOutputStartChar, parity | 0 | 0 |
The control character sequence that restarts
output if the charPortOutFlowType parameter
(in the char MIB) is set to xonXoff. |
| 1.3.6.1.4.1.15.2.3.7.1.10 |
anxpOutputStopChar, modemDCD | 0 | 0 |
The control character sequence that stops
output if the charPortOutFlowType parameter
(in the char MIB) is set to xonXoff. |
| 1.3.6.1.4.1.15.2.3.7.1.11 |
anxpIxanyFlowCtl, modemDTR | 0 | 0 |
This parameter specifies whether any input
character will be treated as a start (xon)
character when output has been suspended by
… |
| 1.3.6.1.4.1.15.2.3.7.1.12 |
anxpLongBreak, modemCTS | 0 | 0 |
This parameter controls whether the Annex
returns the user to the CLI prompt after
receiving a break greater than two seconds. |
| 1.3.6.1.4.1.15.2.3.7.1.13 |
anxpShortBreak, modemRTS | 0 | 0 |
This parameter controls whether the Annex
returns the user to the CLI prompt after
receiving a break shorter than two seconds. |
| 1.3.6.1.4.1.15.2.3.7.1.14 |
anxpForwardTimer, charsIn | 0 | 0 |
This parameter defines the inter-character
timer that sets the amount of time, in tens of
milliseconds, that will elapse before
fo… |
| 1.3.6.1.4.1.15.2.3.7.1.15 |
anxpForwardCount, charsOut | 0 | 0 |
Specifies the number of received characters
buffered for the port by the Annex before
forwarding the characters to the host or
net… |
| 1.3.6.1.4.1.15.2.3.7.1.16 |
anxpImask7Bits, errsParity | 0 | 0 |
When enabled, instructs the Annex to ignore
the eighth bit of all received characters
on the port. |
| 1.3.6.1.4.1.15.2.3.7.1.17 |
anxpAttnChar, errsOverrun | 0 | 0 |
Defines a control character sequence as an
attention character to return the user to
the CLI prompt. The Annex-II only allows
a s… |
| 1.3.6.1.4.1.15.2.3.7.1.18 |
anxpInputBufSize, errsFraming | 0 | 0 |
The number of 256-byte blocks allocated to
receive input characters from this port. |
| 1.3.6.1.4.1.15.2.3.7.1.19 |
anxpInputIsActivity, inCC | 0 | 0 |
Controls whether received input characters
are considered as activity for the port. |
| 1.3.6.1.4.1.15.2.3.7.1.20 |
anxpOutputIsActivity, outCC | 0 | 0 |
Controls whether transmitted output characters
are considered as activity for the port. |
| 1.3.6.1.4.1.15.2.3.7.1.21 |
anxpInactivityTimer | 0 | 0 |
The amount of time, in minutes, which a port
can remain inactive before the Annex terminates
all sessions and resets the port. A… |
| 1.3.6.1.4.1.15.2.3.7.1.22 |
anxpResetIdleTimer | 0 | 0 |
Defines whether input or output resets the
idle timer for the port. |
| 1.3.6.1.4.1.15.2.3.7.1.23 |
anxpCliInactivity | 0 | 0 |
The amount of time, in minutes, that the Annex
waits before hanging up the serial port after
it becomes idle. A value of 0 turns… |
| 1.3.6.1.4.1.15.2.3.7.1.24 |
anxpCliSecurity | 0 | 0 |
This parameter controls whether security is
enabled for the port. |
| 1.3.6.1.4.1.15.2.3.7.1.25 |
anxpConnectSecurity | 0 | 0 |
This parameter controls whether the host-based
security policy is enabled for access from the
port to the network. |
| 1.3.6.1.4.1.15.2.3.7.1.26 |
anxpPortServerSecurity | 0 | 0 |
This parameter controls whether the host-based
security policy is enabled for access to the
port from the port server. |
| 1.3.6.1.4.1.15.2.3.7.1.27 |
anxpPortPassword | 0 | 0 |
This parameter defines a password for the
port for local password protection. |
| 1.3.6.1.4.1.15.2.3.7.1.28 |
anxpUserName | 0 | 0 |
A string defining the user name for the
user of the serial port. |
| 1.3.6.1.4.1.15.2.3.7.1.29 |
anxpDedicatedAddr | 0 | 0 |
When the anxpMode parameter is set to dedicated,
this parameter defines the Internet address
of the host to which this port can c… |
| 1.3.6.1.4.1.15.2.3.7.1.30 |
anxpDedicatedPort | 0 | 0 |
The application name or TCP port number to
which this port can connect when the anxpMode
parameter is set to dedicated. The allo… |
| 1.3.6.1.4.1.15.2.3.7.1.31 |
anxpPrompt | 0 | 0 |
This parameter defines a port-specific
prompt. |
| 1.3.6.1.4.1.15.2.3.7.1.32 |
anxpTermVar | 0 | 0 |
A string defining the type of terminal attached
to the serial port. |
| 1.3.6.1.4.1.15.2.3.7.1.33 |
anxpNewLineTerm | 0 | 0 |
This parameter controls whether a carriage
return is echoed as just a carriage return
(enabled), or whether the carriage return i… |
| 1.3.6.1.4.1.15.2.3.7.1.34 |
anxpEcho | 0 | 0 |
This parameter controls whether the Annex
echoes all characters as they are received
from the port. |
| 1.3.6.1.4.1.15.2.3.7.1.35 |
anxpMapToLower | 0 | 0 |
When enabled, the Annex translates all upper
case characters to lower case as they are
received from the port. |
| 1.3.6.1.4.1.15.2.3.7.1.36 |
anxpMapToUpper | 0 | 0 |
When enabled, the Annex translates all lower
case characters to upper case as they are
transmitted to the port. |
| 1.3.6.1.4.1.15.2.3.7.1.37 |
anxpHardwareTabs | 0 | 0 |
When enabled, this parameter allows the Annex
to expand ASCII tab characters. |
| 1.3.6.1.4.1.15.2.3.7.1.38 |
anxpCharErase | 0 | 0 |
This parameter controls whether the Annex
echoes the character erase and word erase
characters for a video terminal (enabled)
or f… |
| 1.3.6.1.4.1.15.2.3.7.1.39 |
anxpLineErase | 0 | 0 |
This parameter controls whether the Annex
echoes the line erase character for a video
terminal (enabled) or for a hard-copy termi… |
| 1.3.6.1.4.1.15.2.3.7.1.40 |
anxpEraseChar | 0 | 0 |
Defines the character erase control character
sequence. |
| 1.3.6.1.4.1.15.2.3.7.1.41 |
anxpEraseWord | 0 | 0 |
Defines the word erase control character
sequence. |
| 1.3.6.1.4.1.15.2.3.7.1.42 |
anxpEraseLine | 0 | 0 |
Defines the line erase control character
sequence. |
| 1.3.6.1.4.1.15.2.3.7.1.43 |
anxpRedisplayLine | 0 | 0 |
Defines the reprint line control character
sequence. |
| 1.3.6.1.4.1.15.2.3.7.1.44 |
anxpToggleOutput | 0 | 0 |
Defines the flush control character used to
flush the output buffer. |
| 1.3.6.1.4.1.15.2.3.7.1.45 |
anxpTelnetEscape | 0 | 0 |
Defines the control character that returns the
user to the telnet: prompt when running the
CLI telnet command. |
| 1.3.6.1.4.1.15.2.3.7.1.46 |
anxpNeedDsr | 0 | 0 |
Specifies whether the DSR signal needs to be
asserted when connecting to a slave port. |
| 1.3.6.1.4.1.15.2.3.7.1.48 |
anxpLatbEnable | 0 | 0 |
Controls interpretation of LAT Data-B packets
received from host. |
| 1.3.6.1.4.1.15.2.3.7.1.49 |
anxpSlipSecure | 0 | 0 |
If anxEnableSecurity is not set, this
parameter selects slip session logging. If
anxEnableSecurity is set, this parameter
permits… |
| 1.3.6.1.4.1.15.2.3.7.1.50 |
anxpNetLocalAddr | 0 | 0 |
The Internet address for the Annex's side
of the point-to-point (SLIP or PPP) link. |
| 1.3.6.1.4.1.15.2.3.7.1.51 |
anxpNetRemoteAddr | 0 | 0 |
The Internet address for the host at the
remote end of the point-to-point (SLIP or PPP)
link. |