OID reference
1.3.6.1.4.1.15.2.3.7.1.57
When enabled, the Annex will use TCP/IP header compression on this SLIP link only if the other end of the SLIP link initiates the compression.
Identification
{1 3 6 1 4 1 15 2 3 7 1 57}
Definitions may combine these properties differently.
Numbers refer to source variants above. Each value is shown only for variants that define it.
| Value | Name | Source variants |
|---|---|---|
| 1 | enabled | 1, 2 |
| 2 | disabled | 1, 2 |
At least one MIB declaration places this object in a table row. A value belongs to a row instance; its suffix depends on the row's INDEX or AUGMENTS definition.
In XYLO-PORTS-MIB, the row index anxpPortIndex is declared as INTEGER. A non-negative index value is encoded as one numeric subidentifier. An instance has the form .1.3.6.1.4.1.15.2.3.7.1.57.<anxpPortIndex>. Use an index value actually present on the device and permitted by its MIB. Other definitions can differ.
snmpwalk [connection options] DEVICE .1.3.6.1.4.1.15.2.3.7.1.57
Replace the placeholders with your connection and authentication options. Available permissions and device support can differ from the MIB.
Properties come from available MIB definitions. Actual device support and access can differ. See source records below for original files and qualifications.
Meaning
Identical descriptions are grouped. Different wording and device-specific notes are retained.
Description 1
Parsed from ANNEX-MIB.mib · ANNEX-MIB
Source file: Download ANNEX-MIB.mib
Source file: Download xylogics-annex-mib.txt
Source file: Download xylogics-annex-7_0.txt
Description 2
Historical records
anxpAllowCompression OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS deprecated
DESCRIPTION
"When enabled, the Annex will allow TCP/IP
header compression on this serial link only
if the other end of the serial link initiates
the compression.
This MIB object corresponds to the NA/admin
asynchronous port parameter 'allow_compression'."
::= { portEntry 57 }
anxpSlipAllowCompression OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"When enabled, the Annex will use TCP/IP
header compression on this SLIP link only
if the other end of the SLIP link initiates
the compression."
::= { portEntry 57 }
Registration
| OID | Name | Direct children | Descendants | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.15.2.3.7.1.51 | anxpNetRemoteAddr | 0 | 0 | The Internet address for the host at the remote end of the point-to-point (SLIP or PPP) link. |
| 1.3.6.1.4.1.15.2.3.7.1.52 | anxpSlipSubnetMask | 0 | 0 | The subnet mask for this SLIP interface. |
| 1.3.6.1.4.1.15.2.3.7.1.53 | anxpSlipLoadDumpHost | 0 | 0 | The Internet address of the host from which the Annex receives a load or to which the Annex sends a dump over the SLIP interface. |
| 1.3.6.1.4.1.15.2.3.7.1.54 | anxpNetMetric | 0 | 0 | This parameter defines the hop count to the remote end of the SLIP or PPP interface. |
| 1.3.6.1.4.1.15.2.3.7.1.55 | anxpSlipAllowDump | 0 | 0 | This parameter defines whether the Annex is allowed to dump across a SLIP link. |
| 1.3.6.1.4.1.15.2.3.7.1.56 | anxpSlipDoCompression, anxpDoCompression | 0 | 0 | When enabled, the Annex will start TCP/IP header compression on this SLIP link. |
| 1.3.6.1.4.1.15.2.3.7.1.58 | anxpSlipMtuSize | 0 | 0 | Force the compressed SLIP interface to use a Maximum Transmission Unit (MTU) of either 1024 bytes (large) or 256 bytes (small). … |
| 1.3.6.1.4.1.15.2.3.7.1.59 | anxpSlipNoIcmp | 0 | 0 | When enabled, the Annex will discard any ICMP packets directed to this SLIP link. |
| 1.3.6.1.4.1.15.2.3.7.1.60 | anxpSlipTos | 0 | 0 | When enabled, the Annex sends interactive traffic over this SLIP link before any other traffic. |
| 1.3.6.1.4.1.15.2.3.7.1.61 | anxpPppMru | 0 | 0 | This parameter defines the maximum receive unit in bytes. The default value is 1500. |
| 1.3.6.1.4.1.15.2.3.7.1.62 | anxpPppAcm | 0 | 0 | This parameter specifies which of the first 32 bytes (0x00, ... 0x1F) can be sent as clear text and which need to be escaped. A b… |
| 1.3.6.1.4.1.15.2.3.7.1.63 | anxpPppSecurityProto | 0 | 0 | Defines which security protocol will be used to authenticate the remote user. This parameter must be set and the Annex enable_sec… |
| 1.3.6.1.4.1.15.2.3.7.1.64 | anxpPppUserRemote | 0 | 0 | The username used by the Annex to identify itself if the remote PPP peer asks for authentication. Reading this parameter will r… |
| 1.3.6.1.4.1.15.2.3.7.1.65 | anxpPppPasswdRemote | 0 | 0 | The username used by the Annex to identify itself if the remote PPP peer asks for authentication. Reading this parameter will r… |
| 1.3.6.1.4.1.15.2.3.7.1.66 | anxpLatAuthGroupVal | 0 | 0 | This port parameter specifies which remote group codes are accessible to a user on a particular Annex port. Each port has its own … |
| 1.3.6.1.4.1.15.2.3.7.1.67 | anxpPppDialupAddr | 0 | 0 | When enabled, the Annex requests the PPP dialup addresses from the host-based ACP. |
| 1.3.6.1.4.1.15.2.3.7.1.68 | anxpBanner | 0 | 0 | Specifies whether the Annex banner and message- of-the-day are displayed on the port. The default is enabled. |
| 1.3.6.1.4.1.15.2.3.7.1.69 | anxpPsHistory | 0 | 0 | Specifies how much data to buffer on a slave port. |
| 1.3.6.1.4.1.15.2.3.7.1.70 | anxpLocation | 0 | 0 | A descriptive string for a this port. This string is displayed by the CLI who command. |
| 1.3.6.1.4.1.15.2.3.7.1.71 | anxpType | 0 | 0 | The type of device attached to the port. The default is hardwired. |
| 1.3.6.1.4.1.15.2.3.7.1.72 | anxpCliImask7 | 0 | 0 | Defines whether input at the CLI is masked to 7 bitx. The default is disabled. |
| 1.3.6.1.4.1.15.2.3.7.1.73 | anxpModemVar | 0 | 0 | A string defining the type of modem attached to the serial port. This MIB object corresponds to the NA/admin asynchronous port pa… |
| 1.3.6.1.4.1.15.2.3.7.1.74 | anxpPppNcp | 0 | 0 | The protocol running on the interface. This MIB object corresponds to the NA/admin asynchronous port parameter 'ppp_ncp'. Note tha… |
| 1.3.6.1.4.1.15.2.3.7.1.76 | anxpPhoneNumber | 0 | 0 | The phone number used for this port when doing demand dialing. This MIB object corresponds to the NA/admin asynchronous port para… |
| 1.3.6.1.4.1.15.2.3.7.1.77 | anxpNetInactivity | 0 | 0 | The number of units allowed for serial protocol inactivity on the port. The type of unit, minutes or seconds, is defined by the … |
| 1.3.6.1.4.1.15.2.3.7.1.78 | anxpAtGuest | 0 | 0 | If enabled, allows ARAP guest login service. This MIB object corresponds to the NA/admin asynchronous port parameter 'at_guest'. |
| 1.3.6.1.4.1.15.2.3.7.1.79 | anxpAtNodeid | 0 | 0 | The default AppleTalk node ID hint that is used by the Annex on this port. The address consists of two parts separated by a dot.… |
| 1.3.6.1.4.1.15.2.3.7.1.80 | anxpAtSecurity | 0 | 0 | Controls whether ACP service is enabled for this port when establishing an AppleTalk connection. This MIB object corresponds to t… |
| 1.3.6.1.4.1.15.2.3.7.1.81 | anxpArapV42bis | 0 | 0 | Controls whether V.42bis compression is done during an ARAP session. This MIB object corresponds to the NA/admin asynchronous por… |
| 1.3.6.1.4.1.15.2.3.7.1.82 | anxpTn3270PrinterHost | 0 | 0 | The IP address of the machine running a Berkeley-style lpd server. This MIB object corresponds to the NA/admin asynchronous port … |
| 1.3.6.1.4.1.15.2.3.7.1.83 | anxpTn3270PrinterName | 0 | 0 | A valid printer name contained in the /etc/printcap file on the remote host. This MIB object corresponds to the NA/admin asynchro… |
| 1.3.6.1.4.1.15.2.3.7.1.84 | anxpTcpKeepAlive | 0 | 0 | The default keep-alive value for connections to this serial port. If this is zero, use the value specified by anxTcpKeepAlive. T… |
| 1.3.6.1.4.1.15.2.3.7.1.86 | anxpDtrSignal | 0 | 0 | Controls the DTR (Data Terminal Ready) output control signal for this serial port. Valid set values are high or low. Setting the … |
| 1.3.6.1.4.1.15.2.3.7.1.87 | anxpRtsSignal | 0 | 0 | Controls the RTS (Request to Send) output control signal for this serial port. Valid set values are high or low. Setting the valu… |
| 1.3.6.1.4.1.15.2.3.7.1.88 | anxpCliInterface | 0 | 0 | Specifies either a Unix or VMS command line interface. The default is uci. This MIB object corresponds to the NA/admin asynchrono… |
| 1.3.6.1.4.1.15.2.3.7.1.89 | anxpAutobaud | 0 | 0 | When enabled, specifies that the line speed should be determined when opening the connection. The default is disabled. This MIB … |
| 1.3.6.1.4.1.15.2.3.7.1.90 | anxpDefSessMode | 0 | 0 | The default session mode when the DECServer command interface is configured. The default is interactive. This MIB object corres… |
| 1.3.6.1.4.1.15.2.3.7.1.91 | anxpIpxSecurity | 0 | 0 | Controls whether IPX security is enabled on this port. The default is disabled. This MIB object corresponds to the NA/admin asyn… |
| 1.3.6.1.4.1.15.2.3.7.1.92 | anxpIpsoClass | 0 | 0 | Defines the IP security classification for packets sent and received on this port. The default value is none. This MIB object co… |
| 1.3.6.1.4.1.15.2.3.7.1.93 | anxpVciLoginPortPasswd | 0 | 0 | Enables the port password if the port is configured as a DECServer interface port. The default is disabled. This MIB object corre… |
| 1.3.6.1.4.1.15.2.3.7.1.94 | anxpVciLoginTimeout | 0 | 0 | Enables a login timer if the port is configured as a DECServer interface port. The default is disabled. This MIB object correspo… |
| 1.3.6.1.4.1.15.2.3.7.1.95 | anxpDedicatedArgs | 0 | 0 | Command line arguments to be passed to process started by a dedicated port with mode set to 'telnet', 'tn3270', 'rlogin', 'connec… |
| 1.3.6.1.4.1.15.2.3.7.1.96 | anxpNetInactivityUnits | 0 | 0 | The type of units that are used for the port's net inactivity timer. See also the anxpNetInactivity object. The default value is… |
| 1.3.6.1.4.1.15.2.3.7.1.97 | anxpResolveProtocol | 0 | 0 | Default host protocol to use when starting a dedicated port and the protocol is not explicitly specified in the command. Is set … |
| 1.3.6.1.4.1.15.2.3.7.1.98 | anxpForwardKey | 0 | 0 | Defines a control character sequence as an attention character to switch the user to the next session. The Annex-II only allows a… |
| 1.3.6.1.4.1.15.2.3.7.1.99 | anxpBackwardKey | 0 | 0 | Defines a control character sequence as an attention character to switch the user to the previous session. The Annex-II only all… |
| 1.3.6.1.4.1.15.2.3.7.1.100 | anxpPppIpxNetwork | 0 | 0 | The IPX network number for an IPX PPP connection using this port. When the IPX PPP connection is established the network number w… |
| 1.3.6.1.4.1.15.2.3.7.1.101 | anxpPppIpxNode | 0 | 0 | The IPX node number for an IPX PPP connection using this port. The value of this object is a 12 digit hexadecimal number string re… |
| 1.3.6.1.4.1.15.2.3.7.1.102 | anxpLatAuthMap | 0 | 0 | This port parameter is functionally identical to anxpLatAuthGroupVal and corresponds to the NA/admin Annex parameter 'group_value… |
| 1.3.6.1.4.1.15.2.3.7.1.103 | anxpMultiSession | 0 | 0 | This parameter allows multisession operation to be managed on a per port basis. This MIB object corresponds to the NA/admin port … |