| 1.3.6.1.4.1.15.2.3.7.1.51 |
anxpNetRemoteAddr | 0 | 0 |
The Internet address for the host at the
remote end of the point-to-point (SLIP or PPP)
link. |
| 1.3.6.1.4.1.15.2.3.7.1.52 |
anxpSlipSubnetMask | 0 | 0 |
The subnet mask for this SLIP interface. |
| 1.3.6.1.4.1.15.2.3.7.1.53 |
anxpSlipLoadDumpHost | 0 | 0 |
The Internet address of the host from which
the Annex receives a load or to which the
Annex sends a dump over the SLIP interface. |
| 1.3.6.1.4.1.15.2.3.7.1.54 |
anxpNetMetric | 0 | 0 |
This parameter defines the hop count to
the remote end of the SLIP or PPP interface. |
| 1.3.6.1.4.1.15.2.3.7.1.55 |
anxpSlipAllowDump | 0 | 0 |
This parameter defines whether the Annex is
allowed to dump across a SLIP link. |
| 1.3.6.1.4.1.15.2.3.7.1.56 |
anxpSlipDoCompression, anxpDoCompression | 0 | 0 |
When enabled, the Annex will start TCP/IP
header compression on this SLIP link. |
| 1.3.6.1.4.1.15.2.3.7.1.57 |
anxpSlipAllowCompression, anxpAllowCompression | 0 | 0 |
When enabled, the Annex will use TCP/IP
header compression on this SLIP link only
if the other end of the SLIP link initiates
the … |
| 1.3.6.1.4.1.15.2.3.7.1.58 |
anxpSlipMtuSize | 0 | 0 |
Force the compressed SLIP interface to use
a Maximum Transmission Unit (MTU) of either
1024 bytes (large) or 256 bytes (small). … |
| 1.3.6.1.4.1.15.2.3.7.1.59 |
anxpSlipNoIcmp | 0 | 0 |
When enabled, the Annex will discard any
ICMP packets directed to this SLIP link. |
| 1.3.6.1.4.1.15.2.3.7.1.60 |
anxpSlipTos | 0 | 0 |
When enabled, the Annex sends interactive
traffic over this SLIP link before any other
traffic. |
| 1.3.6.1.4.1.15.2.3.7.1.61 |
anxpPppMru | 0 | 0 |
This parameter defines the maximum receive
unit in bytes. The default value is 1500. |
| 1.3.6.1.4.1.15.2.3.7.1.62 |
anxpPppAcm | 0 | 0 |
This parameter specifies which of the first
32 bytes (0x00, ... 0x1F) can be sent as
clear text and which need to be escaped. A
b… |
| 1.3.6.1.4.1.15.2.3.7.1.63 |
anxpPppSecurityProto | 0 | 0 |
Defines which security protocol will be used
to authenticate the remote user. This
parameter must be set and the Annex
enable_sec… |
| 1.3.6.1.4.1.15.2.3.7.1.64 |
anxpPppUserRemote | 0 | 0 |
The username used by the Annex to identify itself if the remote PPP peer asks for authentication. Reading this parameter will r… |
| 1.3.6.1.4.1.15.2.3.7.1.65 |
anxpPppPasswdRemote | 0 | 0 |
The username used by the Annex to identify itself if the remote PPP peer asks for authentication. Reading this parameter will r… |
| 1.3.6.1.4.1.15.2.3.7.1.66 |
anxpLatAuthGroupVal | 0 | 0 |
This port parameter specifies which remote
group codes are accessible to a user on a
particular Annex port. Each port has its own
… |
| 1.3.6.1.4.1.15.2.3.7.1.67 |
anxpPppDialupAddr | 0 | 0 |
When enabled, the Annex requests the
PPP dialup addresses from the host-based
ACP. |
| 1.3.6.1.4.1.15.2.3.7.1.68 |
anxpBanner | 0 | 0 |
Specifies whether the Annex banner and message-
of-the-day are displayed on the port. The
default is enabled. |
| 1.3.6.1.4.1.15.2.3.7.1.69 |
anxpPsHistory | 0 | 0 |
Specifies how much data to buffer on a slave
port. |
| 1.3.6.1.4.1.15.2.3.7.1.70 |
anxpLocation | 0 | 0 |
A descriptive string for a this port. This
string is displayed by the CLI who command. |
| 1.3.6.1.4.1.15.2.3.7.1.71 |
anxpType | 0 | 0 |
The type of device attached to the port. The
default is hardwired. |
| 1.3.6.1.4.1.15.2.3.7.1.72 |
anxpCliImask7 | 0 | 0 |
Defines whether input at the CLI is masked to
7 bitx. The default is disabled. |
| 1.3.6.1.4.1.15.2.3.7.1.73 |
anxpModemVar | 0 | 0 |
A string defining the type of modem attached
to the serial port.
This MIB object corresponds to the NA/admin
asynchronous port pa… |
| 1.3.6.1.4.1.15.2.3.7.1.74 |
anxpPppNcp | 0 | 0 |
The protocol running on the interface.
This MIB object corresponds to the NA/admin
asynchronous port parameter 'ppp_ncp'.
Note tha… |
| 1.3.6.1.4.1.15.2.3.7.1.76 |
anxpPhoneNumber | 0 | 0 |
The phone number used for this port when doing
demand dialing.
This MIB object corresponds to the NA/admin
asynchronous port para… |
| 1.3.6.1.4.1.15.2.3.7.1.77 |
anxpNetInactivity | 0 | 0 |
The number of units allowed for serial protocol
inactivity on the port. The type of unit, minutes
or seconds, is defined by the … |
| 1.3.6.1.4.1.15.2.3.7.1.78 |
anxpAtGuest | 0 | 0 |
If enabled, allows ARAP guest login service.
This MIB object corresponds to the NA/admin
asynchronous port parameter 'at_guest'. |
| 1.3.6.1.4.1.15.2.3.7.1.79 |
anxpAtNodeid | 0 | 0 |
The default AppleTalk node ID hint that is
used by the Annex on this port. The address
consists of two parts separated by a dot.… |
| 1.3.6.1.4.1.15.2.3.7.1.80 |
anxpAtSecurity | 0 | 0 |
Controls whether ACP service is enabled for
this port when establishing an AppleTalk
connection.
This MIB object corresponds to t… |
| 1.3.6.1.4.1.15.2.3.7.1.81 |
anxpArapV42bis | 0 | 0 |
Controls whether V.42bis compression is done
during an ARAP session.
This MIB object corresponds to the NA/admin
asynchronous por… |
| 1.3.6.1.4.1.15.2.3.7.1.82 |
anxpTn3270PrinterHost | 0 | 0 |
The IP address of the machine running a
Berkeley-style lpd server.
This MIB object corresponds to the NA/admin
asynchronous port … |
| 1.3.6.1.4.1.15.2.3.7.1.83 |
anxpTn3270PrinterName | 0 | 0 |
A valid printer name contained in the
/etc/printcap file on the remote host.
This MIB object corresponds to the NA/admin
asynchro… |
| 1.3.6.1.4.1.15.2.3.7.1.84 |
anxpTcpKeepAlive | 0 | 0 |
The default keep-alive value for connections
to this serial port. If this is zero, use the
value specified by anxTcpKeepAlive.
T… |
| 1.3.6.1.4.1.15.2.3.7.1.86 |
anxpDtrSignal | 0 | 0 |
Controls the DTR (Data Terminal Ready) output
control signal for this serial port. Valid set
values are high or low. Setting the … |
| 1.3.6.1.4.1.15.2.3.7.1.87 |
anxpRtsSignal | 0 | 0 |
Controls the RTS (Request to Send) output control
signal for this serial port. Valid set values are
high or low. Setting the valu… |
| 1.3.6.1.4.1.15.2.3.7.1.88 |
anxpCliInterface | 0 | 0 |
Specifies either a Unix or VMS command line interface.
The default is uci.
This MIB object corresponds to the NA/admin
asynchrono… |
| 1.3.6.1.4.1.15.2.3.7.1.89 |
anxpAutobaud | 0 | 0 |
When enabled, specifies that the line speed should be
determined when opening the connection. The default
is disabled.
This MIB … |
| 1.3.6.1.4.1.15.2.3.7.1.90 |
anxpDefSessMode | 0 | 0 |
The default session mode when the DECServer command
interface is configured. The default is interactive.
This MIB object corres… |
| 1.3.6.1.4.1.15.2.3.7.1.91 |
anxpIpxSecurity | 0 | 0 |
Controls whether IPX security is enabled on
this port. The default is disabled.
This MIB object corresponds to the NA/admin
asyn… |
| 1.3.6.1.4.1.15.2.3.7.1.92 |
anxpIpsoClass | 0 | 0 |
Defines the IP security classification for
packets sent and received on this port. The
default value is none.
This MIB object co… |
| 1.3.6.1.4.1.15.2.3.7.1.93 |
anxpVciLoginPortPasswd | 0 | 0 |
Enables the port password if the port is
configured as a DECServer interface port.
The default is disabled.
This MIB object corre… |
| 1.3.6.1.4.1.15.2.3.7.1.94 |
anxpVciLoginTimeout | 0 | 0 |
Enables a login timer if the port is configured
as a DECServer interface port. The default
is disabled.
This MIB object correspo… |
| 1.3.6.1.4.1.15.2.3.7.1.95 |
anxpDedicatedArgs | 0 | 0 |
Command line arguments to be passed to process
started by a dedicated port with mode set to
'telnet', 'tn3270', 'rlogin', 'connec… |
| 1.3.6.1.4.1.15.2.3.7.1.97 |
anxpResolveProtocol | 0 | 0 |
Default host protocol to use when starting a
dedicated port and the protocol is not explicitly
specified in the command. Is set … |
| 1.3.6.1.4.1.15.2.3.7.1.98 |
anxpForwardKey | 0 | 0 |
Defines a control character sequence as an
attention character to switch the user to
the next session. The Annex-II only allows
a… |
| 1.3.6.1.4.1.15.2.3.7.1.99 |
anxpBackwardKey | 0 | 0 |
Defines a control character sequence as an
attention character to switch the user to
the previous session. The Annex-II only all… |
| 1.3.6.1.4.1.15.2.3.7.1.100 |
anxpPppIpxNetwork | 0 | 0 |
The IPX network number for an IPX PPP connection
using this port. When the IPX PPP connection is
established the network number w… |
| 1.3.6.1.4.1.15.2.3.7.1.101 |
anxpPppIpxNode | 0 | 0 |
The IPX node number for an IPX PPP connection
using this port.
The value of this object is a 12 digit
hexadecimal number string re… |
| 1.3.6.1.4.1.15.2.3.7.1.102 |
anxpLatAuthMap | 0 | 0 |
This port parameter is functionally identical to
anxpLatAuthGroupVal and corresponds to the
NA/admin Annex parameter 'group_value… |
| 1.3.6.1.4.1.15.2.3.7.1.103 |
anxpMultiSession | 0 | 0 |
This parameter allows multisession operation to
be managed on a per port basis. This MIB object
corresponds to the NA/admin port … |