OID reference
1.3.6.1.4.1.164.6.2.45.1.1
This MIB object indicates the function that will be enabled or disabled in the device. alarmForwarding= Fault Propagation (usually towards user port). For Vmux: routing (2) - enable/disable Router backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH. uplinkLoopDetect (5) - enable/disable Loop Detection…
Identification
{1 3 6 1 4 1 164 6 2 45 1 1}
Definitions may combine these properties differently.
Numbers refer to source variants above. Each value is shown only for variants that define it. Notes below names come from selected MIB definitions.
| Value | Name and source notes | Source variants |
|---|---|---|
| 2 | routing | 1, 2, 3 |
| 3 | backup | 1, 2, 3 |
| 4 | alarmForwarding | 1, 2, 3 |
| 5 | uplinkLoopDetect | 1, 2, 3 |
| 6 | systemClock | 1, 2, 3 |
| 7 | nps | 2, 3 |
| 8 | ethOamCfm | 2 |
| 9 | fileTransfer | 2 |
| 10 | netEq Network Equalizer (for Voice Quality) | 2 |
| 11 | ecan Echo Canceler | 2 |
| 12 | cli Command Line Interface | 2 |
| 13 | csm Clock Selection model | 2 |
| 14 | erp | 2 |
| 15 | eps | 2 |
| 16 | tdmPwProtect | 2 |
| 17 | pathSdhSonetProtect | 2 |
| 18 | aps | 2 |
| 19 | ethPortProtect | 2 |
| 20 | tdmPortProtect | 2 |
| 21 | tdmPW | 2 |
| 22 | fileSystem | 2 |
| 23 | ssfp | 2 |
| 24 | ptp 1588 Recovered clock | 2 |
| 25 | copyFile | 2 |
| 26 | router | 2 |
| 27 | tbd not in use | 2 |
| 28 | faultManagement | 2 |
| 29 | configChangeSync NE Configuration Change Support | 2 |
| 30 | binaryDataRetrievalMethod Binary Data Retrieval from device | 2 |
| 31 | bridge | 2 |
| 32 | acl | 2 |
| 33 | ospf | 2 |
| 34 | bgp | 2 |
| 35 | bfd | 2 |
| 36 | performanceManagement | 2 |
| 37 | ituSat Y.1564 support | 2 |
| 38 | genericPpp Generic PPP & PPPoE | 2 |
| 39 | policer Policer Profile | 2 |
| 40 | lldp LLDP | 2 |
| 41 | twamp TWAMP | 2 |
| 42 | flow | 2 |
| 43 | vrrp Virtual Router Redundancy Protocol | 2 |
| 44 | l3Sat | 2 |
| 45 | portFlowMirroring | 2 |
| 46 | ethPort Ethernet Port | 2 |
| 47 | dhcpL2Relay DHCP Layer 2 Relay | 2 |
| 48 | nat NAT | 2 |
| 49 | cellular Cellular | 2 |
At least one MIB declaration places this object in a table row. A value belongs to a row instance; its suffix depends on the row's INDEX or AUGMENTS definition.
In RAD-MIB, the row index agnFunction is declared as INTEGER. A non-negative index value is encoded as one numeric subidentifier. An instance has the form .1.3.6.1.4.1.164.6.2.45.1.1.<agnFunction>. Use an index value actually present on the device and permitted by its MIB. Other definitions can differ.
A query example is omitted because the source variants do not establish compatible read access.
Properties come from available MIB definitions. Actual device support and access can differ. See source records below for original files and qualifications.
Available source records contain 3 distinct definitions; some records may not include a definition.
agnFunction OBJECT-TYPE
SYNTAX INTEGER
{
routing (2),
backup (3),
alarmForwarding (4),
uplinkLoopDetect (5),
systemClock (6)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This MIB object indicates the function that will be enabled or disabled
in the device.
alarmForwarding= Fault Propagation (usually towards user port).
For Vmux:
routing (2) - enable/disable Router
backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH.
uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink.
systemClock (6) - enable/disable the System Clock.
"
::= { agnFunctionEntry 1 }agnFunction OBJECT-TYPE
SYNTAX INTEGER
{
routing (2),
backup (3),
alarmForwarding (4),
uplinkLoopDetect (5),
systemClock (6),
nps (7),
ethOamCfm (8),
fileTransfer (9),
netEq (10), -- Network Equalizer (for Voice Quality)
ecan (11), -- Echo Canceler
cli (12), -- Command Line Interface
csm (13), -- Clock Selection model
erp (14),
eps (15),
tdmPwProtect (16),
pathSdhSonetProtect (17),
aps (18),
ethPortProtect (19),
tdmPortProtect (20),
tdmPW (21),
fileSystem (22),
ssfp (23),
ptp (24), -- 1588 Recovered clock
copyFile (25),
router (26),
tbd (27), -- not in use
faultManagement (28),
configChangeSync (29), -- NE Configuration Change Support
binaryDataRetrievalMethod (30), -- Binary Data Retrieval from device
bridge (31),
acl (32),
ospf (33),
bgp (34),
bfd (35),
performanceManagement (36),
ituSat (37), -- Y.1564 support
genericPpp (38), -- Generic PPP & PPPoE
policer (39), -- Policer Profile
lldp (40), -- LLDP
twamp (41), -- TWAMP
flow (42),
vrrp (43), -- Virtual Router Redundancy Protocol
l3Sat (44),
portFlowMirroring (45),
ethPort (46), -- Ethernet Port
dhcpL2Relay (47), -- DHCP Layer 2 Relay
nat (48), -- NAT
cellular (49) -- Cellular
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This MIB object indicates the function that will be enabled or disabled
in the device.
alarmForwarding= Fault Propagation (usually towards user port).
For Vmux:
routing (2) - enable/disable Router
backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH.
uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink.
systemClock (6) - enable/disable the System Clock.
nps (7) - N+1 Protection Switching device physically connected to I/O
modules in Gmux2000.
ethOamCfm (8) - denotes that the device supports ETH OAM CFM (802.1ag).
The list of supported CFM attributes is specified in agnFunctionAttributes.
Different from the other functions, the manager cannot activate the CFM.
agnFunctionActivation is set only by the agent. A value of enable (3)
denotes that the device supports ETH OAM CFM.
fileTransfer (9) - denotes that the device supports file transfer functions
and agnFunctionAttributes object which lists the supported functions.
Similar to ETH OAM CFM, agnFunctionActivation is set only by the agent.
A value of enable(3) denotes that the device supports file transfer functions
and agnFunctionAttributes.
erp (14) - Ethernet Ring Protection according to the G.8032 standard
The general protection related capabilitites eps(15), tdmPwProtect(16),
pathSdhSonetProtect(17), aps(18), ethPortProtect(19) and tdmPortProtect(20)
are correlated to the definition of the ProtectClassType.
eps (15) - Ethernet Protection Switching according to the G.8031 standard
tdmPwProtect (16) - TDM PW protection
pathSdhSonetProtect (17) - SDH/SONET VC Path Protection
aps (18) - SONET (APS) or SDH (MSP) switching protection
ethPortProtect (19) - Ethernet port protection
tdmPortProtect (20)- TDM port protection
tdmPw (21) - TDM PW functionality, for supported options see
the agnFunctionAttributes below.
fileSystem (22) - File System support
ssfp (23) - Smart SFP support
acl (32) - access control list (security)
lldp (40) - Link Layer Discovery Protocol
twamp (41) - Two Way Active Measurement Protocol
flow (42) - flow
vrrp (43) - Virtual Router Redundancy Protocol
portFlowMirroring (45) - Port and flow mirroring
ethPort (46) - Ethernet port capabilities
dhcpL2Relay (47) - DHCP Layer 2 Relay
nat (48) - Network Address Translator/Translation
cellular (49) - Cellular
"
::= { agnFunctionEntry 1 }agnFunction OBJECT-TYPE
SYNTAX INTEGER
{
routing (2),
backup (3),
alarmForwarding (4),
uplinkLoopDetect (5),
systemClock (6),
nps (7)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This MIB object indicates the function that will be enabled or disabled
in the device.
alarmForwarding= Fault Propagation (usually towards user port).
For Vmux:
routing (2) - enable/disable Router
backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH.
uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink.
systemClock (6) - enable/disable the System Clock.
nps (7) - N+1 Protection Switching device physically connected to I/O
modules in Gmux2000.
"
::= { agnFunctionEntry 1 }
Meaning
Identical descriptions are grouped. Different wording and device-specific notes are retained.
Description 1
This MIB object indicates the function that will be enabled or disabled in the device. alarmForwarding= Fault Propagation (usually towards user port). For Vmux: routing (2) - enable/disable Router backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH. uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink. systemClock (6) - enable/disable the System Clock.
Description 2
This MIB object indicates the function that will be enabled or disabled in the device. alarmForwarding= Fault Propagation (usually towards user port). For Vmux: routing (2) - enable/disable Router backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH. uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink. systemClock (6) - enable/disable the System Clock. nps (7) - N+1 Protection Switching device physically connected to I/O modules in Gmux2000. ethOamCfm (8) - denotes that the device supports ETH OAM CFM (802.1ag). The list of supported CFM attributes is specified in agnFunctionAttributes. Different from the other functions, the manager cannot activate the CFM. agnFunctionActivation is set only by the agent. A value of enable (3) denotes that the device supports ETH OAM CFM. fileTransfer (9) - denotes that the device supports file transfer functions and agnFunctionAttributes object which lists the supported functions. Similar to ETH OAM CFM, agnFunctionActivation is set only by the agent. A value of enable(3) denotes that the device supports file transfer functions and agnFunctionAttributes. erp (14) - Ethernet Ring Protection according to the G.8032 standard The general protection related capabilitites eps(15), tdmPwProtect(16), pathSdhSonetProtect(17), aps(18), ethPortProtect(19) and tdmPortProtect(20) are correlated to the definition of the ProtectClassType. eps (15) - Ethernet Protection Switching according to the G.8031 standard tdmPwProtect (16) - TDM PW protection pathSdhSonetProtect (17) - SDH/SONET VC Path Protection aps (18) - SONET (APS) or SDH (MSP) switching protection ethPortProtect (19) - Ethernet port protection tdmPortProtect (20)- TDM port protection tdmPw (21) - TDM PW functionality, for supported options see the agnFunctionAttributes below. fileSystem (22) - File System support ssfp (23) - Smart SFP support acl (32) - access control list (security) lldp (40) - Link Layer Discovery Protocol twamp (41) - Two Way Active Measurement Protocol flow (42) - flow vrrp (43) - Virtual Router Redundancy Protocol portFlowMirroring (45) - Port and flow mirroring ethPort (46) - Ethernet port capabilities dhcpL2Relay (47) - DHCP Layer 2 Relay nat (48) - Network Address Translator/Translation cellular (49) - Cellular
Description 3
This MIB object indicates the function that will be enabled or disabled in the device. alarmForwarding= Fault Propagation (usually towards user port). For Vmux: routing (2) - enable/disable Router backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH. uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink. systemClock (6) - enable/disable the System Clock. nps (7) - N+1 Protection Switching device physically connected to I/O modules in Gmux2000.
Evidence
Matching descriptions are grouped; open a group to compare definitions and supporting files.
Status in source: current.
Names: agnFunction
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"agnFunction",
"OBJECT-TYPE",
"SYNTAX",
"INTEGER",
"{",
"routing",
"(",
"2",
")",
",",
"backup",
"(",
"3",
")",
",",
"alarmForwarding",
"(",
"4",
")",
",",
"uplinkLoopDetect",
"(",
"5",
")",
",",
"systemClock",
"(",
"6",
")",
"}",
"MAX-ACCESS",
"not-accessible",
"STATUS",
"current",
"DESCRIPTION",
"\"This MIB object indicates the function that will be enabled or disabled in the device. alarmForwarding= Fault Propagation (usually towards user port). For Vmux: routing (2) - enable/disable Router backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH. uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink. systemClock (6) - enable/disable the System Clock. \"",
"::=",
"{",
"agnFunctionEntry",
"1",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"INTEGER",
[
"enumSpec",
[
[
"routing",
2
],
[
"backup",
3
],
[
"alarmForwarding",
4
],
[
"uplinkLoopDetect",
5
],
[
"systemClock",
6
]
]
]
],
null,
[
"MaxAccessPart",
"not-accessible"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"This MIB object indicates the function that will be enabled or disabled in the device. alarmForwarding= Fault Propagation (usually towards user port). For Vmux: routing (2) - enable/disable Router backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH. uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink. systemClock (6) - enable/disable the System Clock."
],
null,
null,
null,
null
]
}Vendor MIB copy from the Netdisco archive.
Module: RAD-MIB
See published definition above
{'IF-MIB': ['InterfaceIndex', 'ifAlias', 'ifIndex', 'ifDescr'], 'ATM-MIB': ['atmVplVpi', 'atmVclVpi', 'atmVclVci', 'atmVpCrossConnectEntry', 'atmVcCrossConnectEntry', 'atmTrafficDescrParamEntry'], 'DS1-MIB': ['dsx1CurrentIndex', 'dsx1IntervalIndex', 'dsx1IntervalNumber', 'dsx1LineIndex', 'dsx1TotalIndex', 'dsx1LineStatus', 'dsx1LineStatusLastChange', 'dsx1LoopbackStatus'], 'DS3-MIB': ['dsx3LineStatus', 'dsx3LoopbackStatus', 'dsx3ConfigEntry'], 'LLDP-MIB': ['LldpPortIdSubtype'], 'SNMPv2-TC': ['RowStatus', 'DateAndTime', 'TimeStamp', 'TEXTUAL-CONVENTION', 'DisplayString', 'MacAddress', 'RowPointer', 'TruthValue'], 'BRIDGE-MIB': ['Timeout', 'BridgeId', 'dot1dBasePortEntry'], 'SNMPv2-SMI': ['TimeTicks', 'enterprises', 'IpAddress', 'OBJECT-TYPE', 'Integer32', 'Counter32', 'Gauge32', 'OBJECT-IDENTITY', 'NOTIFICATION-TYPE', 'Unsigned32', 'Counter64'], 'DOT3-OAM-MIB': ['dot3OamEntry', 'dot3OamOperStatus'], 'Q-BRIDGE-MIB': ['VlanId', 'PortList', 'dot1qVlanStaticEntry'], 'IANAifType-MIB': ['IANAifType'], 'PerfHist-TC-MIB': ['PerfCurrentCount', 'PerfIntervalCount', 'PerfTotalCount'], 'IEEE8021-CFM-MIB': ['dot1agCfmMdIndex', 'dot1agCfmMaIndex', 'dot1agCfmMepIdentifier', 'dot1agCfmMepDbRMepIdentifier'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString'], 'DISMAN-SCHEDULE-MIB': ['schedEntry']}Related source files and packages:
Status in source: current.
Names: agnFunction
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"agnFunction",
"OBJECT-TYPE",
"SYNTAX",
"INTEGER",
"{",
"routing",
"(",
"2",
")",
",",
"backup",
"(",
"3",
")",
",",
"alarmForwarding",
"(",
"4",
")",
",",
"uplinkLoopDetect",
"(",
"5",
")",
",",
"systemClock",
"(",
"6",
")",
",",
"nps",
"(",
"7",
")",
",",
"ethOamCfm",
"(",
"8",
")",
",",
"fileTransfer",
"(",
"9",
")",
",",
"netEq",
"(",
"10",
")",
",",
"ecan",
"(",
"11",
")",
",",
"cli",
"(",
"12",
")",
",",
"csm",
"(",
"13",
")",
",",
"erp",
"(",
"14",
")",
",",
"eps",
"(",
"15",
")",
",",
"tdmPwProtect",
"(",
"16",
")",
",",
"pathSdhSonetProtect",
"(",
"17",
")",
",",
"aps",
"(",
"18",
")",
",",
"ethPortProtect",
"(",
"19",
")",
",",
"tdmPortProtect",
"(",
"20",
")",
",",
"tdmPW",
"(",
"21",
")",
",",
"fileSystem",
"(",
"22",
")",
",",
"ssfp",
"(",
"23",
")",
",",
"ptp",
"(",
"24",
")",
",",
"copyFile",
"(",
"25",
")",
",",
"router",
"(",
"26",
")",
",",
"tbd",
"(",
"27",
")",
",",
"faultManagement",
"(",
"28",
")",
",",
"configChangeSync",
"(",
"29",
")",
",",
"binaryDataRetrievalMethod",
"(",
"30",
")",
",",
"bridge",
"(",
"31",
")",
",",
"acl",
"(",
"32",
")",
",",
"ospf",
"(",
"33",
")",
",",
"bgp",
"(",
"34",
")",
",",
"bfd",
"(",
"35",
")",
",",
"performanceManagement",
"(",
"36",
")",
",",
"ituSat",
"(",
"37",
")",
",",
"genericPpp",
"(",
"38",
")",
",",
"policer",
"(",
"39",
")",
",",
"lldp",
"(",
"40",
")",
",",
"twamp",
"(",
"41",
")",
",",
"flow",
"(",
"42",
")",
",",
"vrrp",
"(",
"43",
")",
",",
"l3Sat",
"(",
"44",
")",
",",
"portFlowMirroring",
"(",
"45",
")",
",",
"ethPort",
"(",
"46",
")",
",",
"dhcpL2Relay",
"(",
"47",
")",
",",
"nat",
"(",
"48",
")",
",",
"cellular",
"(",
"49",
")",
"}",
"MAX-ACCESS",
"not-accessible",
"STATUS",
"current",
"DESCRIPTION",
"\"This MIB object indicates the function that will be enabled or disabled in the device. alarmForwarding= Fault Propagation (usually towards user port). For Vmux: routing (2) - enable/disable Router backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH. uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink. systemClock (6) - enable/disable the System Clock. nps (7) - N+1 Protection Switching device physically connected to I/O modules in Gmux2000. ethOamCfm (8) - denotes that the device supports ETH OAM CFM (802.1ag). The list of supported CFM attributes is specified in agnFunctionAttributes. Different from the other functions, the manager cannot activate the CFM. agnFunctionActivation is set only by the agent. A value of enable (3) denotes that the device supports ETH OAM CFM. fileTransfer (9) - denotes that the device supports file transfer functions and agnFunctionAttributes object which lists the supported functions. Similar to ETH OAM CFM, agnFunctionActivation is set only by the agent. A value of enable(3) denotes that the device supports file transfer functions and agnFunctionAttributes. erp (14) - Ethernet Ring Protection according to the G.8032 standard The general protection related capabilitites eps(15), tdmPwProtect(16), pathSdhSonetProtect(17), aps(18), ethPortProtect(19) and tdmPortProtect(20) are correlated to the definition of the ProtectClassType. eps (15) - Ethernet Protection Switching according to the G.8031 standard tdmPwProtect (16) - TDM PW protection pathSdhSonetProtect (17) - SDH/SONET VC Path Protection aps (18) - SONET (APS) or SDH (MSP) switching protection ethPortProtect (19) - Ethernet port protection tdmPortProtect (20)- TDM port protection tdmPw (21) - TDM PW functionality, for supported options see the agnFunctionAttributes below. fileSystem (22) - File System support ssfp (23) - Smart SFP support acl (32) - access control list (security) lldp (40) - Link Layer Discovery Protocol twamp (41) - Two Way Active Measurement Protocol flow (42) - flow vrrp (43) - Virtual Router Redundancy Protocol portFlowMirroring (45) - Port and flow mirroring ethPort (46) - Ethernet port capabilities dhcpL2Relay (47) - DHCP Layer 2 Relay nat (48) - Network Address Translator/Translation cellular (49) - Cellular \"",
"::=",
"{",
"agnFunctionEntry",
"1",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"INTEGER",
[
"enumSpec",
[
[
"routing",
2
],
[
"backup",
3
],
[
"alarmForwarding",
4
],
[
"uplinkLoopDetect",
5
],
[
"systemClock",
6
],
[
"nps",
7
],
[
"ethOamCfm",
8
],
[
"fileTransfer",
9
],
[
"netEq",
10
],
[
"ecan",
11
],
[
"cli",
12
],
[
"csm",
13
],
[
"erp",
14
],
[
"eps",
15
],
[
"tdmPwProtect",
16
],
[
"pathSdhSonetProtect",
17
],
[
"aps",
18
],
[
"ethPortProtect",
19
],
[
"tdmPortProtect",
20
],
[
"tdmPW",
21
],
[
"fileSystem",
22
],
[
"ssfp",
23
],
[
"ptp",
24
],
[
"copyFile",
25
],
[
"router",
26
],
[
"tbd",
27
],
[
"faultManagement",
28
],
[
"configChangeSync",
29
],
[
"binaryDataRetrievalMethod",
30
],
[
"bridge",
31
],
[
"acl",
32
],
[
"ospf",
33
],
[
"bgp",
34
],
[
"bfd",
35
],
[
"performanceManagement",
36
],
[
"ituSat",
37
],
[
"genericPpp",
38
],
[
"policer",
39
],
[
"lldp",
40
],
[
"twamp",
41
],
[
"flow",
42
],
[
"vrrp",
43
],
[
"l3Sat",
44
],
[
"portFlowMirroring",
45
],
[
"ethPort",
46
],
[
"dhcpL2Relay",
47
],
[
"nat",
48
],
[
"cellular",
49
]
]
]
],
null,
[
"MaxAccessPart",
"not-accessible"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"This MIB object indicates the function that will be enabled or disabled in the device. alarmForwarding= Fault Propagation (usually towards user port). For Vmux: routing (2) - enable/disable Router backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH. uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink. systemClock (6) - enable/disable the System Clock. nps (7) - N+1 Protection Switching device physically connected to I/O modules in Gmux2000. ethOamCfm (8) - denotes that the device supports ETH OAM CFM (802.1ag). The list of supported CFM attributes is specified in agnFunctionAttributes. Different from the other functions, the manager cannot activate the CFM. agnFunctionActivation is set only by the agent. A value of enable (3) denotes that the device supports ETH OAM CFM. fileTransfer (9) - denotes that the device supports file transfer functions and agnFunctionAttributes object which lists the supported functions. Similar to ETH OAM CFM, agnFunctionActivation is set only by the agent. A value of enable(3) denotes that the device supports file transfer functions and agnFunctionAttributes. erp (14) - Ethernet Ring Protection according to the G.8032 standard The general protection related capabilitites eps(15), tdmPwProtect(16), pathSdhSonetProtect(17), aps(18), ethPortProtect(19) and tdmPortProtect(20) are correlated to the definition of the ProtectClassType. eps (15) - Ethernet Protection Switching according to the G.8031 standard tdmPwProtect (16) - TDM PW protection pathSdhSonetProtect (17) - SDH/SONET VC Path Protection aps (18) - SONET (APS) or SDH (MSP) switching protection ethPortProtect (19) - Ethernet port protection tdmPortProtect (20)- TDM port protection tdmPw (21) - TDM PW functionality, for supported options see the agnFunctionAttributes below. fileSystem (22) - File System support ssfp (23) - Smart SFP support acl (32) - access control list (security) lldp (40) - Link Layer Discovery Protocol twamp (41) - Two Way Active Measurement Protocol flow (42) - flow vrrp (43) - Virtual Router Redundancy Protocol portFlowMirroring (45) - Port and flow mirroring ethPort (46) - Ethernet port capabilities dhcpL2Relay (47) - DHCP Layer 2 Relay nat (48) - Network Address Translator/Translation cellular (49) - Cellular"
],
null,
null,
null,
null
]
}Vendor MIB copy from the Observium Community archive. RAD support.
Module: RAD-GEN-MIB
See published definition above
{'IF-MIB': ['ifAlias', 'ifIndex'], 'RAD-TC': ['FileType', 'RadEntityType', 'AlarmForwardingCause'], 'SNMPv2-TC': ['TimeStamp', 'TDomain', 'TAddress', 'TEXTUAL-CONVENTION', 'DisplayString', 'RowStatus', 'DateAndTime', 'RowPointer', 'MacAddress'], 'ENTITY-MIB': ['entPhysicalAlias', 'entPhysicalDescr', 'PhysicalIndexOrZero'], 'SNMPv2-MIB': ['sysName'], 'SNMPv2-SMI': ['Integer32', 'Counter32', 'TimeTicks', 'IpAddress', 'Gauge32', 'Unsigned32', 'OBJECT-TYPE', 'MODULE-IDENTITY', 'NOTIFICATION-TYPE', 'OBJECT-IDENTITY', 'Counter64'], 'RAD-SMI-MIB': ['radGen', 'radSpecificDevices', 'systems', 'fileTransfer'], 'IANAifType-MIB': ['IANAifType'], 'BFD-TC-STD-MIB-R': ['BfdDiagTC', 'BfdIntervalTC'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString'], 'DISMAN-SCHEDULE-MIB': ['schedEntry']}Related source files and packages:
Status in source: current.
Names: agnFunction
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"agnFunction",
"OBJECT-TYPE",
"SYNTAX",
"INTEGER",
"{",
"routing",
"(",
"2",
")",
",",
"backup",
"(",
"3",
")",
",",
"alarmForwarding",
"(",
"4",
")",
",",
"uplinkLoopDetect",
"(",
"5",
")",
",",
"systemClock",
"(",
"6",
")",
",",
"nps",
"(",
"7",
")",
"}",
"MAX-ACCESS",
"not-accessible",
"STATUS",
"current",
"DESCRIPTION",
"\"This MIB object indicates the function that will be enabled or disabled in the device. alarmForwarding= Fault Propagation (usually towards user port). For Vmux: routing (2) - enable/disable Router backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH. uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink. systemClock (6) - enable/disable the System Clock. nps (7) - N+1 Protection Switching device physically connected to I/O modules in Gmux2000. \"",
"::=",
"{",
"agnFunctionEntry",
"1",
"}"
],
"syntax_tree": [
[
"SimpleSyntax",
"INTEGER",
[
"enumSpec",
[
[
"routing",
2
],
[
"backup",
3
],
[
"alarmForwarding",
4
],
[
"uplinkLoopDetect",
5
],
[
"systemClock",
6
],
[
"nps",
7
]
]
]
],
null,
[
"MaxAccessPart",
"not-accessible"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"This MIB object indicates the function that will be enabled or disabled in the device. alarmForwarding= Fault Propagation (usually towards user port). For Vmux: routing (2) - enable/disable Router backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH. uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink. systemClock (6) - enable/disable the System Clock. nps (7) - N+1 Protection Switching device physically connected to I/O modules in Gmux2000."
],
null,
null,
null,
null
]
}Vendor MIB copy from the Observium Community archive. RAD support.
Module: RAD-MIB
See published definition above
{'IF-MIB': ['InterfaceIndex', 'ifAlias', 'ifIndex', 'InterfaceIndexOrZero', 'ifDescr'], 'APS-MIB': ['apsConfigEntry'], 'ATM-MIB': ['atmVplVpi', 'atmVclVpi', 'atmVclVci', 'aal5VccVpi', 'aal5VccVci', 'atmVpCrossConnectEntry', 'atmVcCrossConnectEntry', 'atmTrafficDescrParamEntry', 'atmVclEntry', 'aal5VccEntry'], 'DS1-MIB': ['dsx1LineStatus', 'dsx1LineStatusLastChange', 'dsx1CurrentIndex', 'dsx1LineIndex', 'dsx1IntervalIndex', 'dsx1IntervalNumber', 'dsx1LoopbackStatus', 'dsx1TotalIndex'], 'DS3-MIB': ['dsx3LineStatus', 'dsx3ConfigEntry', 'dsx3LoopbackStatus'], 'IMA-MIB': ['imaGroupIndex', 'imaLinkIfIndex', 'imaGroupFailureStatus'], 'MAU-MIB': ['rpMauMediaAvailable'], 'ATMF-CES': ['atmfCESCbrIndex', 'atmfCESConfEntry'], 'IPOA-MIB': ['ipoaLisIfMappingEntry'], 'ISDN-MIB': ['isdnSignalingEntry'], 'LLDP-MIB': ['LldpPortIdSubtype'], 'SNMPv2-TC': ['TimeStamp', 'TAddress', 'TEXTUAL-CONVENTION', 'DisplayString', 'RowStatus', 'DateAndTime', 'TruthValue', 'RowPointer'], 'ATM-TC-MIB': ['AtmTrafficDescrParamIndex'], 'BRIDGE-MIB': ['Timeout', 'BridgeId', 'dot1dBasePortEntry'], 'SNMPv2-SMI': ['Integer32', 'Counter32', 'TimeTicks', 'enterprises', 'IpAddress', 'Gauge32', 'Unsigned32', 'OBJECT-TYPE', 'MODULE-IDENTITY', 'NOTIFICATION-TYPE', 'OBJECT-IDENTITY', 'Counter64'], 'RFC1381-MIB': ['IfIndexType'], 'DIFFSERV-MIB': ['IndexIntegerNextFree', 'IndexInteger'], 'DOT3-OAM-MIB': ['dot3OamEntry', 'dot3OamOperStatus'], 'Q-BRIDGE-MIB': ['VlanIndex', 'PortList', 'dot1qVlanStaticEntry'], 'DS0BUNDLE-MIB': ['dsx0BundleEntry'], 'FRNETSERV-MIB': ['frPVCEndptDLCIIndex'], 'FDDI-SMT73-MIB': ['fddimibPORTPCMState'], 'IANAifType-MIB': ['IANAifType'], 'MPLS-TC-STD-MIB': ['MplsLabel', 'MplsTunnelIndex', 'MplsOwner', 'MplsLdpIdentifier', 'MplsLsrIdentifier'], 'PerfHist-TC-MIB': ['PerfCurrentCount', 'PerfIntervalCount', 'PerfTotalCount'], 'IEEE8021-CFM-MIB': ['dot1agCfmMdIndex', 'dot1agCfmMaIndex', 'dot1agCfmMepIdentifier', 'dot1agCfmMepDbRMepIdentifier'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber'], 'SNMP-REPEATER-MIB': ['rptrGroupOperStatus', 'rptrPortOperStatus'], 'MULTI-MEDIA-MIB-TC': ['MmTAddressTag', 'MmEndpointID', 'MmAliasAddress', 'MmH323EndpointType', 'MmGatekeeperID', 'MmAliasTag'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString'], 'DISMAN-SCHEDULE-MIB': ['schedEntry'], 'HDSL2-SHDSL-LINE-MIB': ['hdsl2ShdslEndpointCurrEntry', 'hdsl2ShdslInvIndex', 'hdsl2ShdslEndpointSide', 'hdsl2ShdslSpanConfProfileEntry'], 'FR-ATM-PVC-SERVICE-IWF-MIB': ['frAtmIwfConnectionEntry']}Registration
| OID | Name | Direct children | Descendants | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.164.6.2.45.1.2 | agnFunctionActivation | 0 | 0 | |
| 1.3.6.1.4.1.164.6.2.45.1.3 | agnFunctionAttributes | 0 | 0 | |
| 1.3.6.1.4.1.164.6.2.45.1.4 | agnFunctionVersion | 0 | 0 |