| 1.3.6.1.4.1.33.16.7.1.1.1 |
slotIndex | 0 | 0 |
An index value that uniquely identifies a slot, in the range 0 to basicSlotNumber, where the value 0 indicates the same slot as b… |
| 1.3.6.1.4.1.33.16.7.1.1.2 |
slotAdminAction | 0 | 0 |
Control to cause reset of the system in a slot. When read, the value is always 'ready'. Setting to 'reset' or 'resetHold' causes… |
| 1.3.6.1.4.1.33.16.7.1.1.3 |
slotOperStatus | 0 | 0 |
Relative to the chassis, the current operating status of the system in the slot. |
| 1.3.6.1.4.1.33.16.7.1.1.5 |
slotHardwareType | 0 | 0 |
The type of hardware in the slot. |
| 1.3.6.1.4.1.33.16.7.1.1.6 |
slotHardwareSerialNumber | 0 | 0 |
The MRV In-Reach serial number of the function card hardware in this slot. |
| 1.3.6.1.4.1.33.16.7.1.1.7 |
slotHardwareRevision | 0 | 0 |
This revision level of the function card hardware in the slot. |
| 1.3.6.1.4.1.33.16.7.1.1.8 |
slotIOCardType | 0 | 0 |
The hardware type of the I/O card in this slot. |
| 1.3.6.1.4.1.33.16.7.1.1.9 |
slotIOCardSerialNumber | 0 | 0 |
The MRV In-Reach serial number of the I/O card in this slot. |
| 1.3.6.1.4.1.33.16.7.1.1.10 |
slotIOCardOperStatus | 0 | 0 |
Status of the I/O card relative to the function card in this slot. |
| 1.3.6.1.4.1.33.16.7.1.1.11 |
slotBootstrapFirmwareRevision | 0 | 0 |
The firmware revision level of the bootstrap ROM installed in the system in the slot. |
| 1.3.6.1.4.1.33.16.7.1.1.12 |
slotElementalFirmwareRevision | 0 | 0 |
The firmware revision level of the minimal function ROM (management bus microprocessor) installed in the system in the slot. |
| 1.3.6.1.4.1.33.16.7.1.1.13 |
slotMemorySize | 0 | 0 |
The number of bytes of memory installed in the system in the slot. |
| 1.3.6.1.4.1.33.16.7.1.1.14 |
slotLedNumber | 0 | 0 |
The number of LEDs on the system in the slot. A value of 0 indicates none, unknown, or status not readable. |
| 1.3.6.1.4.1.33.16.7.1.1.15 |
slotLedStatus | 0 | 0 |
The status of the LEDs displayed on the front and back of the system in the slot. The first bit is the high-order bit of the fir… |
| 1.3.6.1.4.1.33.16.7.1.1.16 |
slotBase802Address | 0 | 0 |
Base IEEE 802 global address for the slot. |
| 1.3.6.1.4.1.33.16.7.1.1.17 |
slotIpAddress | 0 | 0 |
An internet address to which the system in this slot might respond. May be one of many. |
| 1.3.6.1.4.1.33.16.7.1.1.18 |
slotPlus5Status | 0 | 0 |
Status of the +5 volt power to the slot. |
| 1.3.6.1.4.1.33.16.7.1.1.19 |
slotPlus12Status | 0 | 0 |
Status of the +12 volt power to the slot. |
| 1.3.6.1.4.1.33.16.7.1.1.20 |
slotMinus12Status | 0 | 0 |
Status of the -12 volt power to the slot. |
| 1.3.6.1.4.1.33.16.7.1.1.21 |
slotPlus5Watts | 0 | 0 |
Tenths of watts of +5 volt power currently drawn by the slot. |
| 1.3.6.1.4.1.33.16.7.1.1.22 |
slotPlus12Watts | 0 | 0 |
Tenths of watts of +12 volt power currently drawn by the slot. |
| 1.3.6.1.4.1.33.16.7.1.1.23 |
slotMinus12Watts | 0 | 0 |
Tenths of watts of -12 volt power currently drawn by the slot. |
| 1.3.6.1.4.1.33.16.7.1.1.24 |
slotIOCardHardwareVersion | 0 | 0 |
Version number of I/O card in the slot. |
| 1.3.6.1.4.1.33.16.7.1.1.25 |
slotRestoreNVS | 0 | 0 |
Setting to 'execute' causes the non-volatile parameter storage to be restored from an installed memory card. Setting to 'ready' … |
| 1.3.6.1.4.1.33.16.7.1.1.26 |
slotDefaultNVS | 0 | 0 |
Setting to 'execute' causes non-volatile stored parameters to be reset to factory defaults. Setting to 'ready' has no effect. |
| 1.3.6.1.4.1.33.16.7.1.1.27 |
slotVlnNumber | 0 | 0 |
The current VLN used by the CPU on this Agent. A null value indicates VLNs are not supported by the Agent. |
| 1.3.6.1.4.1.33.16.7.1.1.28 |
slotSwitchPlaneStatus | 0 | 0 |
Indicates the state of the SwitchPlane. For hardware types that do not support a SwitchPlane interface, not supported is returne… |