Health Check interval in minutes.
Parsed from file ADIC-SANMGR-PROXY-MIB.mib
Module: ADIC-SANMGR-PROXY-MIB
paHealthCheckInterval OBJECT-TYPE SYNTAX Gauge ACCESS read-write STATUS mandatory DESCRIPTION "Health Check interval in minutes." ::= { agentScalarEntry 5 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.1 | paIdentify | 0 | 0 | Flash the READY light on the SAN Data Gateway front panel. A non-zero value turns the LED on for the specified number of seconds. … |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.2 | paReboot | 0 | 0 | Writing a reboot(2) value here causes immediate reboot. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.3 | paHealthCheckValue | 0 | 0 | Value in percent of health check tests passed. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.4 | paHealthCheckLevel | 0 | 0 | Scrutiny level of health check function. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.6 | paEvRptLevel | 0 | 0 | Used when retrieving Event Log. Events with log level greater than paEvRptLevel are not retrieved. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.7 | paEventLogLevels | 0 | 0 | Each of 255 event types has an 8-bit level used when reading log. Currently valid LogLevel range is 0-3. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.8 | paTrapThresholds | 0 | 0 | Each of 255 event types has an 8-bit threshold. When the number of events exceeds the Trap Threshold, a trap is generated and sen… |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.9 | paBaudRate | 0 | 0 | Serial baud rate for SAN Gateway Service Port. Currently, the Agent does not support baud rate change: the rate is hard-coded to … |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.11 | paLogSize | 0 | 0 | Number of records in entire event log. (Not just current records since boot.) |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.12 | paCommand | 0 | 0 | Used for issuing command to SNMP agent. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.13 | paLogBoot | 0 | 0 | Absolute index of first log entry at boot. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.14 | paLogNCurrent | 0 | 0 | SNMP Get (read) returns number of records since boot subject to viewing level filtering. SNMP Set (write) copies this number of r… |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.15 | paLogChronFirst | 0 | 0 | Used to request range of records from paLogChronFirst to paLogChronLast |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.16 | paLogChronLast | 0 | 0 | Used to request range of records from paLogChronFirst to paLogChronLast |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.17 | paLogScroll | 0 | 0 | Used to request previous/next range of records event log |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.18 | paLogFilename | 0 | 0 | Used to save event log to a file. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.19 | paEnvironmentState | 0 | 0 | Temperature and Voltage Status of SAN Data Gateway: ********************************** (LSB) bit 0 Auxiliary Power bit 1 Main Pow… |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.20 | paGatewayFWRev | 0 | 0 | SAN Data Gateway Firmware Revision information. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.21 | paGatewayHWRev | 0 | 0 | SAN Data Gateway Hardware Revision information. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.22 | paSnmpFWRev | 0 | 0 | SNMP Agent Firmware Revision information. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.23 | paRidTag | 0 | 0 | SAN Data Gateway RIDTag. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.24 | paSerialNumber | 0 | 0 | SAN Data Gateway Serial Number. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.25 | paServerVersion | 0 | 0 | Remote Management software writes Server version information here to customize SNMP Agent behavior. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.26 | paProductType | 0 | 0 | Type of SAN device |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.27 | paVPSEnabled | 0 | 0 | State of VPS Access Control enable. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.28 | paLicenseKey | 0 | 0 | Used to pass feature enabling license keys. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.29 | paThirdPartyCopyEnabled | 0 | 0 | State of Extended 3rd Party Copy enable. Enabled means that a valid license key has been entered for this feature. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.30 | paVPSStatus | 0 | 0 | State of Virtual Private SAN feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. Bit 1 is redundant with MIB … |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.31 | paThirdPartyCopyStatus | 0 | 0 | State of Extended 3rd Party Copy feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. Bit 1 is redundant with … |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.32 | paCommandControlLUN | 0 | 0 | Gateway/Router Command and Control LUN |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.33 | paSanDirectorEnabled | 0 | 0 | State of SAN Director Support for this device. To enable, user must write a valid license key to OID paLicenseKey or enter the li… |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.34 | paNodeName | 0 | 0 | SAN Gateway Node Name. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.35 | paVPMStatus | 0 | 0 | State of Virtual Private Map feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.36 | paSRSStatus | 0 | 0 | State of SAN Replication Services feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.37 | paEthernetType | 0 | 0 | Current Ethernet Speed. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.38 | paTrapSequenceNumber | 0 | 0 | Sequence number of last trap sent by this SNMP Agent. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.39 | paSysNodeNameMode | 0 | 0 | Algorithm used when computing Fibre Channel World Wide Node Name for each port. If the value is sameForEachPort(0), then the Wor… |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.40 | paGhostIOTimeToLive | 0 | 0 | The amount of time that commands can remain queued in the SNC before being considered stale and discarded. 0 : Never discard … |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.41 | paMaxLun | 0 | 0 | The maximum LUN value possible. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.42 | paEVPSEnabled | 0 | 0 | Bit 0: EVPS active if 1, inactive if 0 Bit 1: EVPS licensed if 1, unlicensed if 0 |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.43 | paMaxHostLun | 0 | 0 | The number of devices one host can see |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.44 | paAMPStatus | 0 | 0 | Status of Automatic Multipath feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.45 | paEnableAllScsiTargets | 0 | 0 | Used to Enable/Disable all-scsi-targets. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.46 | paHPFStatus | 0 | 0 | Bit 0: HPF active if 1, inactive if 0 Bit 1: HPF licensed if 1, unlicensed if 0 |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.47 | paSoip2iRescan | 0 | 0 | Writing true(1) here causes SOIP2 initiator to rescan its bus. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.48 | paSoipiRescan | 0 | 0 | Writing true(1) here causes SOIP initiator to rescan its bus. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.49 | paFLBStatus | 0 | 0 | Status of Load Balancing feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.50 | paSoip2iScanPeriod | 0 | 0 | SOIP2 Initiator Scan period in seconds. 0 will disable scan. |
| 1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.51 | paCommandFlowLogEnabled | 0 | 0 | Returns TRUE iff Command Flow Logging is available. Returns FALSE otherwise. |