OID reference

zxAdslLinePMConfPMSF

1.3.6.1.4.1.3902.1004.4.1.1.1.1

Description

This configuration parameter defines the line states to be forced by the near-end ATU on this line. It is coded as an integer value with following definition: L0_FullOn Force the line to transition from the L3 idle state to the L0 full-on state. This transition requires the (short) initialization procedures. After rea…

Full description and source information

Identification

Identifier and names

Parent
1.3.6.1.4.1.3902.1004.4.1.1.1 (zxAdslLineEntry)
Node code
1
Node name
zxAdslLinePMConfPMSF
Category
SNMP management object
Numeric OID
1.3.6.1.4.1.3902.1004.4.1.1.1.1
URN notation
urn:oid:1.3.6.1.4.1.3902.1004.4.1.1.1.1
ASN.1, OID-IRI and named path variants
ASN.1 notation

{1 3 6 1 4 1 3902 1004 4 1 1 1 1}

  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprise(1) zte(3902) zxDsl(1004) zxAdslExtMib(4) zxAdslExtMibObjects(1) zxAdslLineTable(1) zxAdslLineEntry(1) zxAdslLinePMConfPMSF(1)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprise(1) zxEnterpriseMib(3902) zxDsl(1004) zxAdslExtMib(4) zxAdslExtMibObjects(1) zxAdslLineTable(1) zxAdslLineEntry(1) zxAdslLinePMConfPMSF(1)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprises(1) zte(3902) zxDsl(1004) zxAdslExtMib(4) zxAdslExtMibObjects(1) zxAdslLineTable(1) zxAdslLineEntry(1) zxAdslLinePMConfPMSF(1)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprises(1) zxEnterpriseMib(3902) zxDsl(1004) zxAdslExtMib(4) zxAdslExtMibObjects(1) zxAdslLineTable(1) zxAdslLineEntry(1) zxAdslLinePMConfPMSF(1)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) ldap-enterprise(1) zte(3902) zxDsl(1004) zxAdslExtMib(4) zxAdslExtMibObjects(1) zxAdslLineTable(1) zxAdslLineEntry(1) zxAdslLinePMConfPMSF(1)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) ldap-enterprise(1) zxEnterpriseMib(3902) zxDsl(1004) zxAdslExtMib(4) zxAdslExtMibObjects(1) zxAdslLineTable(1) zxAdslLineEntry(1) zxAdslLinePMConfPMSF(1)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) vendor-objects(1) zte(3902) zxDsl(1004) zxAdslExtMib(4) zxAdslExtMibObjects(1) zxAdslLineTable(1) zxAdslLineEntry(1) zxAdslLinePMConfPMSF(1)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) vendor-objects(1) zxEnterpriseMib(3902) zxDsl(1004) zxAdslExtMib(4) zxAdslExtMibObjects(1) zxAdslLineTable(1) zxAdslLineEntry(1) zxAdslLinePMConfPMSF(1)}
  • {iso(1) org(3) dod(6) internet(1) private(4) enterprise(1) zte(3902) zxDsl(1004) zxAdslExtMib(4) zxAdslExtMibObjects(1) zxAdslLineTable(1) zxAdslLineEntry(1) zxAdslLinePMConfPMSF(1)}
  • {iso(1) org(3) dod(6) internet(1) private(4) enterprise(1) zxEnterpriseMib(3902) zxDsl(1004) zxAdslExtMib(4) zxAdslExtMibObjects(1) zxAdslLineTable(1) zxAdslLineEntry(1) zxAdslLinePMConfPMSF(1)}
  • {iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) zte(3902) zxDsl(1004) zxAdslExtMib(4) zxAdslExtMibObjects(1) zxAdslLineTable(1) zxAdslLineEntry(1) zxAdslLinePMConfPMSF(1)}
  • {iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) zxEnterpriseMib(3902) zxDsl(1004) zxAdslExtMib(4) zxAdslExtMibObjects(1) zxAdslLineTable(1) zxAdslLineEntry(1) zxAdslLinePMConfPMSF(1)}
  • {iso(1) org(3) dod(6) internet(1) private(4) ldap-enterprise(1) zte(3902) zxDsl(1004) zxAdslExtMib(4) zxAdslExtMibObjects(1) zxAdslLineTable(1) zxAdslLineEntry(1) zxAdslLinePMConfPMSF(1)}
  • {iso(1) org(3) dod(6) internet(1) private(4) ldap-enterprise(1) zxEnterpriseMib(3902) zxDsl(1004) zxAdslExtMib(4) zxAdslExtMibObjects(1) zxAdslLineTable(1) zxAdslLineEntry(1) zxAdslLinePMConfPMSF(1)}
  • {iso(1) org(3) dod(6) internet(1) private(4) vendor-objects(1) zte(3902) zxDsl(1004) zxAdslExtMib(4) zxAdslExtMibObjects(1) zxAdslLineTable(1) zxAdslLineEntry(1) zxAdslLinePMConfPMSF(1)}
  • {iso(1) org(3) dod(6) internet(1) private(4) vendor-objects(1) zxEnterpriseMib(3902) zxDsl(1004) zxAdslExtMib(4) zxAdslExtMibObjects(1) zxAdslLineTable(1) zxAdslLineEntry(1) zxAdslLinePMConfPMSF(1)}
  • Additional combinations skipped.
OID-IRI notation
  • /1/3/6/1/4/1/3902/1004/4/1/1/1/1
  • /ISO/Identified-Organization/6/1/4/1/3902/1004/4/1/1/1/1
  • /ISO/3/6/1/4/1/3902/1004/4/1/1/1/1
Named path variants
  • /iso/identified-organization/dod/internet/private/enterprise/3902/zxDsl/zxAdslExtMib/zxAdslExtMibObjects/zxAdslLineTable/zxAdslLineEntry/zxAdslLinePMConfPMSF
  • /iso/identified-organization/dod/internet/private/enterprise/zte/zxDsl/zxAdslExtMib/zxAdslExtMibObjects/zxAdslLineTable/zxAdslLineEntry/zxAdslLinePMConfPMSF
  • /iso/identified-organization/dod/internet/private/enterprise/zxEnterpriseMib/zxDsl/zxAdslExtMib/zxAdslExtMibObjects/zxAdslLineTable/zxAdslLineEntry/zxAdslLinePMConfPMSF
  • /iso/identified-organization/dod/internet/private/enterprises/3902/zxDsl/zxAdslExtMib/zxAdslExtMibObjects/zxAdslLineTable/zxAdslLineEntry/zxAdslLinePMConfPMSF
  • /iso/identified-organization/dod/internet/private/enterprises/zte/zxDsl/zxAdslExtMib/zxAdslExtMibObjects/zxAdslLineTable/zxAdslLineEntry/zxAdslLinePMConfPMSF
  • /iso/identified-organization/dod/internet/private/enterprises/zxEnterpriseMib/zxDsl/zxAdslExtMib/zxAdslExtMibObjects/zxAdslLineTable/zxAdslLineEntry/zxAdslLinePMConfPMSF
  • /iso/identified-organization/dod/internet/private/ldap-enterprise/3902/zxDsl/zxAdslExtMib/zxAdslExtMibObjects/zxAdslLineTable/zxAdslLineEntry/zxAdslLinePMConfPMSF
  • /iso/identified-organization/dod/internet/private/ldap-enterprise/zte/zxDsl/zxAdslExtMib/zxAdslExtMibObjects/zxAdslLineTable/zxAdslLineEntry/zxAdslLinePMConfPMSF
  • /iso/identified-organization/dod/internet/private/ldap-enterprise/zxEnterpriseMib/zxDsl/zxAdslExtMib/zxAdslExtMibObjects/zxAdslLineTable/zxAdslLineEntry/zxAdslLinePMConfPMSF
  • /iso/identified-organization/dod/internet/private/vendor-objects/3902/zxDsl/zxAdslExtMib/zxAdslExtMibObjects/zxAdslLineTable/zxAdslLineEntry/zxAdslLinePMConfPMSF
  • /iso/identified-organization/dod/internet/private/vendor-objects/zte/zxDsl/zxAdslExtMib/zxAdslExtMibObjects/zxAdslLineTable/zxAdslLineEntry/zxAdslLinePMConfPMSF
  • /iso/identified-organization/dod/internet/private/vendor-objects/zxEnterpriseMib/zxDsl/zxAdslExtMib/zxAdslExtMibObjects/zxAdslLineTable/zxAdslLineEntry/zxAdslLinePMConfPMSF
  • /iso/org/dod/internet/private/enterprise/3902/zxDsl/zxAdslExtMib/zxAdslExtMibObjects/zxAdslLineTable/zxAdslLineEntry/zxAdslLinePMConfPMSF
  • /iso/org/dod/internet/private/enterprise/zte/zxDsl/zxAdslExtMib/zxAdslExtMibObjects/zxAdslLineTable/zxAdslLineEntry/zxAdslLinePMConfPMSF
  • /iso/org/dod/internet/private/enterprise/zxEnterpriseMib/zxDsl/zxAdslExtMib/zxAdslExtMibObjects/zxAdslLineTable/zxAdslLineEntry/zxAdslLinePMConfPMSF
  • /iso/org/dod/internet/private/enterprises/3902/zxDsl/zxAdslExtMib/zxAdslExtMibObjects/zxAdslLineTable/zxAdslLineEntry/zxAdslLinePMConfPMSF
  • Additional combinations skipped.

SNMP properties

Value type
INTEGER
Maximum access defined by MIB
read-create
Status in MIB
current
Default value
1

Enumerated values

ValueName
1l0_FullOn
3l2_LowPower
4l3_Idle

Using this OID with SNMP

At least one MIB declaration places this object in a table row. A value belongs to a row instance; its suffix depends on the row's INDEX or AUGMENTS definition. The index encoding is not inferred here.

Published row index: ifIndex.

snmpwalk [connection options] DEVICE .1.3.6.1.4.1.3902.1004.4.1.1.1.1

Replace the placeholders with your connection and authentication options. Available permissions and device support can differ from the MIB.

Properties come from available MIB definitions. Actual device support and access can differ. See source records below for original files and qualifications.

The displayed source records contain one distinct definition. Compare its source records.

zxAdslLinePMConfPMSF  OBJECT-TYPE
        SYNTAX      INTEGER {
            l0_FullOn   (1),
            l2_LowPower (3),
            l3_Idle     (4)
            }
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "This configuration parameter defines the line states to be forced by 
            the near-end ATU on this line. It is coded as an integer value with 
            following definition:
                L0_FullOn   Force the line to transition from the L3 idle state 
                            to the L0 full-on state. This transition requires 
                            the (short) initialization procedures. After 
                            reaching the L0 state, the line may transition into 
                            or exit from the L2 low power state (if L2 state is 
                            enabled). If the L0 state is not reached (after a 
                            vendor discretionary number of retries and/or within
                            a vendor discretionary timeout), then an 
                            Initialization Failure occurs. Whenever the line is 
                            in the L3 state, attemps shall be made to transition 
                            to the L0 state until it is forced into another 
                            state through this configuration parameter.
                L2_LowPower Force the line to transition from L0 full on to L2 
                            low power state. This transition requires the entry 
                            into L2 mode. This is a out-of-service test value 
                            for triggering the L2 mode.
                L3_Idle     Force the line to transition from the L0 full-on or
                            L2 low power state to the L3 idle state. This 
                            transition requires the (orderly) shutdown procedure. 
                            After reaching the L3 state, the line shall remain 
                            in the L3 idle state until it is forced into another 
                            state through this configuration parameter.
                
                Forced line state transitions require the line to enter or exit 
                from the L3 idle state. These transitions are not restricted by 
                the Line state enabling parameter value.
                
                NOTE - Supported for ADSL2/ADSL2plus ONLY.
                       This configuration parameter maps to the AdminStatus of 
                the line, which is part of the GeneralInformationGroup object 
                group specified in RFC 2233, and may not need to be duplicated 
                in the ADSL MIB. See also RFC2662. The Administrative Status of 
                the line is UP when the line is forced to the L0 state and is 
                DOWN when the line is forced to the L3 state."

        REFERENCE "Section 7.3.1.1.3 Power management state forced (PMSF), 
                   G.997.1 (05/2003) "
        DEFVAL { 1 }                   
        ::= { zxAdslLineEntry 1 }

Meaning

Descriptions

1 unique

Identical descriptions are grouped. Different wording and device-specific notes are retained.

This configuration parameter defines the line states to be forced by the near-end ATU on this line. It is coded as an integer value with following definition: L0_FullOn Force the line to transition from the L3 idle state to the L0 full-on state. This transition requires the (short) initialization procedures. After reaching the L0 state, the line may transition into or exit from the L2 low power state (if L2 state is enabled). If the L0 state is not reached (after a vendor discretionary number of retries and/or within a vendor discretionary timeout), then an Initialization Failure occurs. Whenever the line is in the L3 state, attemps shall be made to transition to the L0 state until it is forced into another state through this configuration parameter. L2_LowPower Force the line to transition from L0 full on to L2 low power state. This transition requires the entry into L2 mode. This is a out-of-service test value for triggering the L2 mode. L3_Idle Force the line to transition from the L0 full-on or L2 low power state to the L3 idle state. This transition requires the (orderly) shutdown procedure. After reaching the L3 state, the line shall remain in the L3 idle state until it is forced into another state through this configuration parameter. Forced line state transitions require the line to enter or exit from the L3 idle state. These transitions are not restricted by the Line state enabling parameter value. NOTE - Supported for ADSL2/ADSL2plus ONLY. This configuration parameter maps to the AdminStatus of the line, which is part of the GeneralInformationGroup object group specified in RFC 2233, and may not need to be duplicated in the ADSL MIB. See also RFC2662. The Administrative Status of the line is UP when the line is forced to the L0 state and is DOWN when the line is forced to the L3 state.

Sources for this description

ZTE MIB copies (LibreNMS/Observium Community)

See 1 matching source record

Evidence

Source records

1 records

Matching descriptions are grouped; open a group to compare definitions and supporting files.

Records for description 1ZTE MIB copies (LibreNMS/Observium Community)1 record · 1 source

Description 1

zxAdslLinePMConfPMSF · currentZTE MIB copies (LibreNMS/Observium Community)1 source

Status in source: current.

Names: zxAdslLinePMConfPMSF

Technical details
{
  "smi_kind": "OBJECT-TYPE",
  "definition": [
    "zxAdslLinePMConfPMSF",
    "OBJECT-TYPE",
    "SYNTAX",
    "INTEGER",
    "{",
    "l0_FullOn",
    "(",
    "1",
    ")",
    ",",
    "l2_LowPower",
    "(",
    "3",
    ")",
    ",",
    "l3_Idle",
    "(",
    "4",
    ")",
    "}",
    "MAX-ACCESS",
    "read-create",
    "STATUS",
    "current",
    "DESCRIPTION",
    "\"This configuration parameter defines the line states to be forced by the near-end ATU on this line. It is coded as an integer value with following definition: L0_FullOn Force the line to transition from the L3 idle state to the L0 full-on state. This transition requires the (short) initialization procedures. After reaching the L0 state, the line may transition into or exit from the L2 low power state (if L2 state is enabled). If the L0 state is not reached (after a vendor discretionary number of retries and/or within a vendor discretionary timeout), then an Initialization Failure occurs. Whenever the line is in the L3 state, attemps shall be made to transition to the L0 state until it is forced into another state through this configuration parameter. L2_LowPower Force the line to transition from L0 full on to L2 low power state. This transition requires the entry into L2 mode. This is a out-of-service test value for triggering the L2 mode. L3_Idle Force the line to transition from the L0 full-on or L2 low power state to the L3 idle state. This transition requires the (orderly) shutdown procedure. After reaching the L3 state, the line shall remain in the L3 idle state until it is forced into another state through this configuration parameter. Forced line state transitions require the line to enter or exit from the L3 idle state. These transitions are not restricted by the Line state enabling parameter value. NOTE - Supported for ADSL2/ADSL2plus ONLY. This configuration parameter maps to the AdminStatus of the line, which is part of the GeneralInformationGroup object group specified in RFC 2233, and may not need to be duplicated in the ADSL MIB. See also RFC2662. The Administrative Status of the line is UP when the line is forced to the L0 state and is DOWN when the line is forced to the L3 state.\"",
    "REFERENCE",
    "\"Section 7.3.1.1.3 Power management state forced (PMSF), G.997.1 (05/2003) \"",
    "DEFVAL",
    "{",
    "1",
    "}",
    "::=",
    "{",
    "zxAdslLineEntry",
    "1",
    "}"
  ],
  "syntax_tree": [
    [
      "SimpleSyntax",
      "INTEGER",
      [
        "enumSpec",
        [
          [
            "l0_FullOn",
            1
          ],
          [
            "l2_LowPower",
            3
          ],
          [
            "l3_Idle",
            4
          ]
        ]
      ]
    ],
    null,
    [
      "MaxAccessPart",
      "read-create"
    ],
    [
      "Status",
      "current"
    ],
    [
      "DESCRIPTION",
      "This configuration parameter defines the line states to be forced by the near-end ATU on this line. It is coded as an integer value with following definition: L0_FullOn Force the line to transition from the L3 idle state to the L0 full-on state. This transition requires the (short) initialization procedures. After reaching the L0 state, the line may transition into or exit from the L2 low power state (if L2 state is enabled). If the L0 state is not reached (after a vendor discretionary number of retries and/or within a vendor discretionary timeout), then an Initialization Failure occurs. Whenever the line is in the L3 state, attemps shall be made to transition to the L0 state until it is forced into another state through this configuration parameter. L2_LowPower Force the line to transition from L0 full on to L2 low power state. This transition requires the entry into L2 mode. This is a out-of-service test value for triggering the L2 mode. L3_Idle Force the line to transition from the L0 full-on or L2 low power state to the L3 idle state. This transition requires the (orderly) shutdown procedure. After reaching the L3 state, the line shall remain in the L3 idle state until it is forced into another state through this configuration parameter. Forced line state transitions require the line to enter or exit from the L3 idle state. These transitions are not restricted by the Line state enabling parameter value. NOTE - Supported for ADSL2/ADSL2plus ONLY. This configuration parameter maps to the AdminStatus of the line, which is part of the GeneralInformationGroup object group specified in RFC 2233, and may not need to be duplicated in the ADSL MIB. See also RFC2662. The Administrative Status of the line is UP when the line is forced to the L0 state and is DOWN when the line is forced to the L3 state."
    ],
    [
      "REFERENCE",
      "Section 7.3.1.1.3 Power management state forced (PMSF), G.997.1 (05/2003)"
    ],
    null,
    null,
    [
      "DEFVAL",
      1
    ]
  ]
}

Registration

Registration authorities

First Registration Authority (inferred from ancestor 1.3.6.1.4.1.3902)

Xianlin Luo

Siblings (7)

OIDNameDirect childrenDescendantsDescription
1.3.6.1.4.1.3902.1004.4.1.1.1.2 zxAdslLinePMState00
1.3.6.1.4.1.3902.1004.4.1.1.1.3 zxAdslLineDMTTrellis00
1.3.6.1.4.1.3902.1004.4.1.1.1.4 zxAdslLineTxAtmCells00
1.3.6.1.4.1.3902.1004.4.1.1.1.5 zxAdslLineRxAtmCells00
1.3.6.1.4.1.3902.1004.4.1.1.1.6 zxAdslLineIdleCells00
1.3.6.1.4.1.3902.1004.4.1.1.1.7 zxAdslLineTxDataRate00
1.3.6.1.4.1.3902.1004.4.1.1.1.8 zxAdslLineRxDataRate00