Allows the shaping to be disabled/enabled on V.FC modems.
Parsed from file HDM.MIB.txt
Company: cai
Module: HDM-MIB
Vendor: 3Com
Module: HDM-MIB (HDM.MIB)
Type: TABULAR
Access: read-write
Syntax: INTEGER
Automatically extracted from www.mibdepot.com
hdmScVFCShaping OBJECT-TYPE SYNTAX INTEGER{ enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Allows the shaping to be disabled/enabled on V.FC modems." ::= { hdmScEntry 31 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.429.1.22.3.1.1.1 | hdmScIndex | 0 | 0 | The unique value found in the chassis mib entity relation table that references this modem. |
| 1.3.6.1.4.1.429.1.22.3.1.1.2 | hdmScIndex2 | 0 | 0 | The Secondary unique value found in the chassis mib entity relation table that references this modem. |
| 1.3.6.1.4.1.429.1.22.3.1.1.3 | hdmScLinkRateMin | 0 | 0 | Determines the Minimum link rate |
| 1.3.6.1.4.1.429.1.22.3.1.1.4 | hdmScLinkRateMax | 0 | 0 | Determines the Maximum link Rate |
| 1.3.6.1.4.1.429.1.22.3.1.1.5 | hdmScNonArqBufSize | 0 | 0 | Sets the sizer of the transmit buffer for non-ARQ mode operation to either 128 bytes or 1.5K. The smaller size is for low speed … |
| 1.3.6.1.4.1.429.1.22.3.1.1.6 | hdmScNonMnpDataCapture | 0 | 0 | Causes received characters to be buffered when the modem is attempting to negotiate an MNP call and the remote modem is not. Def… |
| 1.3.6.1.4.1.429.1.22.3.1.1.7 | hdmScV21Mod | 0 | 0 | When enabled, the modem will answer both bell 103 and V.21 calls but originates only V.21 calls. Default=disabled. |
| 1.3.6.1.4.1.429.1.22.3.1.1.8 | hdmScV32UnencodedMod | 0 | 0 | Allows unencoded modulation in V.32 mode. Although part of the CCITT V.32 recomendation it is rarely used. Default=disabled. |
| 1.3.6.1.4.1.429.1.22.3.1.1.9 | hdmScV32Mod | 0 | 0 | Allows V.32 modulation to be disabled on USRobotics Dual Standard modems. Default=enabled. |
| 1.3.6.1.4.1.429.1.22.3.1.1.10 | hdmScV32Bis | 0 | 0 | Allows V.32 bis modulation to be disabled. On USRobotics Dual Standard modems this may be useful in troublshooting HST operation… |
| 1.3.6.1.4.1.429.1.22.3.1.1.11 | hdmScV32BisEnhance | 0 | 0 | Allows USRobotics V.32 Enahnced mode to be disabled for purposes of troubleshooting Default=enabled. |
| 1.3.6.1.4.1.429.1.22.3.1.1.12 | hdmScV32QuickRetrain | 0 | 0 | Allows the faster retrains that occur with USR's enhanced V.32 mode to be disabled for troubleshooting purposes. Default=enabled. |
| 1.3.6.1.4.1.429.1.22.3.1.1.13 | hdmScV23 | 0 | 0 | Allows the modem to negotiate a V.23 connection(used in U.K.) after failing to negotiate a higher rate. Default=disabled. |
| 1.3.6.1.4.1.429.1.22.3.1.1.14 | hdmScFallback | 0 | 0 | Defines whether or not the modem will be allowed to change protocols it detects a significant change in the line characteristics. … |
| 1.3.6.1.4.1.429.1.22.3.1.1.15 | hdmScV32TerboModeEnable | 0 | 0 | Allows the V32 Terbo mode to be disabled/enabled. |
| 1.3.6.1.4.1.429.1.22.3.1.1.16 | hdmScV34ModeEnable | 0 | 0 | Allows V34 mode to be disabled/enabled. |
| 1.3.6.1.4.1.429.1.22.3.1.1.17 | hdmScVFCSymRate2400 | 0 | 0 | Allows the 2400 symbol rate to be disabled/enabled on V.FC modems. |
| 1.3.6.1.4.1.429.1.22.3.1.1.18 | hdmScVFCSymRate2743 | 0 | 0 | Allows the 2743 symbol rate to be disabled/enabled on V.FC modems. |
| 1.3.6.1.4.1.429.1.22.3.1.1.19 | hdmScVFCSymRate2800 | 0 | 0 | Allows the 2800 symbol rate to be disabled/enabled on V.FC modems. |
| 1.3.6.1.4.1.429.1.22.3.1.1.20 | hdmScVFCSymRate3000 | 0 | 0 | Allows the 3000 symbol rate to be disabled/enabled on V.FC modems. |
| 1.3.6.1.4.1.429.1.22.3.1.1.21 | hdmScVFCSymRate3200 | 0 | 0 | Allows the 3200 symbol rate to be disabled/enabled on V.FC modems. |
| 1.3.6.1.4.1.429.1.22.3.1.1.22 | hdmScVFCSymRate3429 | 0 | 0 | Allows the 3429 symbol rate to be disabled/enabled on V.FC modems. |
| 1.3.6.1.4.1.429.1.22.3.1.1.23 | hdmScVFC8S2DMapping | 0 | 0 | Allows the 8S-2D mapping to be disabled/enabled on V.FC modems. |
| 1.3.6.1.4.1.429.1.22.3.1.1.24 | hdmScVFC16S4DMapping | 0 | 0 | Allows the 16S-4D mapping to be disabled/enabled on V.FC modems. |
| 1.3.6.1.4.1.429.1.22.3.1.1.25 | hdmScVFC32S2DMapping | 0 | 0 | Allows the 32S-2D mapping to be disabled/enabled on V.FC modems. |
| 1.3.6.1.4.1.429.1.22.3.1.1.26 | hdmScVFC64S4DMapping | 0 | 0 | Allows the 64S-4D mapping to be disabled/enabled on V.FC modems. |
| 1.3.6.1.4.1.429.1.22.3.1.1.27 | hdmScVFCNonLinearCoding | 0 | 0 | Allows the non-linear coding to be disabled/enabled on V.FC modems. |
| 1.3.6.1.4.1.429.1.22.3.1.1.28 | hdmScVFCTxLevelDeviation | 0 | 0 | Allows the TX level deviation to be disabled/enabled on V.FC modems. |
| 1.3.6.1.4.1.429.1.22.3.1.1.29 | hdmScVFCPreEmphasis | 0 | 0 | Allows the pre-emphasis to be disabled/enabled on V.FC modems. |
| 1.3.6.1.4.1.429.1.22.3.1.1.30 | hdmScVFCPreCoding | 0 | 0 | Allows the precoding to be disabled/enabled on V.FC modems. |
| 1.3.6.1.4.1.429.1.22.3.1.1.32 | hdmScVFCModeEnable | 0 | 0 | Allows to disable/enable V.FC mode in order to troubleshoot a connection. |
| 1.3.6.1.4.1.429.1.22.3.1.1.33 | hdmScV8 | 0 | 0 | Allow V8 mode to be disabled/enabled |
| 1.3.6.1.4.1.429.1.22.3.1.1.34 | hdmSCV8CallIndicator | 0 | 0 | Allow V.8. call indicater to be disabled/enabled. |
| 1.3.6.1.4.1.429.1.22.3.1.1.35 | hdmScV34pModeEnable | 0 | 0 | Allows V34 plus modulation mode to be disabled. (default=0/enabled) |
| 1.3.6.1.4.1.429.1.22.3.1.1.36 | hdmScX2LowerSpeedMin | 0 | 0 | Lower speed direction minimum speed Default=0 |
| 1.3.6.1.4.1.429.1.22.3.1.1.37 | hdmScX2LowerSpeedMax | 0 | 0 | Lower speed direction maximum speed Default=0 |
| 1.3.6.1.4.1.429.1.22.3.1.1.38 | hdmScX2DisableClient | 0 | 0 | X2 Client Mode Disable Default=enable. |
| 1.3.6.1.4.1.429.1.22.3.1.1.39 | hdmScX2DisableServer | 0 | 0 | X2 Server Mode Disable Default=enable. |
| 1.3.6.1.4.1.429.1.22.3.1.1.40 | hdmScX2DIsableSymmetric | 0 | 0 | X2 Symmetric Mode Disable Default=enable. |
| 1.3.6.1.4.1.429.1.22.3.1.1.53 | hdmSc300 | 0 | 0 | Restrict 300 baud negotiations. Register S48.0 Default is disable (0) restriction. |
| 1.3.6.1.4.1.429.1.22.3.1.1.54 | hdmSc1200 | 0 | 0 | Restrict 1200 baud negotiations. Register S48.1 Default is disable (0) restriction. |
| 1.3.6.1.4.1.429.1.22.3.1.1.55 | hdmSc2400 | 0 | 0 | Restrict 2400 baud negotiations. Register S48.2 Default is disable (0) restriction. |
| 1.3.6.1.4.1.429.1.22.3.1.1.56 | hdmScHighSpeed | 0 | 0 | Restrict highspeed baud negotiations. Register S48.3 Default is disable (0) restriction. |
| 1.3.6.1.4.1.429.1.22.3.1.1.57 | hdmScSelectiveReject | 0 | 0 | Selective Reject register S51.6 is a function of the V.42/LAPM protocol. The default is enable (1) |
| 1.3.6.1.4.1.429.1.22.3.1.1.58 | hdmScHighPowerConst | 0 | 0 | This object is used to enable/disable the X2 high-power constellation. This object is only valid in countries, where it is legal.… |
| 1.3.6.1.4.1.429.1.22.3.1.1.59 | hdmScV90Analogue | 0 | 0 | This object is used to enable/disable the V.90 client (APCM) modulation. Default= enable(1). |
| 1.3.6.1.4.1.429.1.22.3.1.1.60 | hdmScV90Digital | 0 | 0 | This object is used to enable/disable the V.90 server modulation (DPCM). Default= enable(1). |
| 1.3.6.1.4.1.429.1.22.3.1.1.61 | hdmScV90AllDigital | 0 | 0 | This object is used to enable/disable the V.90 symmetric modulation (DDPCM). Default= enable(1). |
| 1.3.6.1.4.1.429.1.22.3.1.1.62 | hdmScTxPwrLvl | 0 | 0 | This object configures the power level. |
| 1.3.6.1.4.1.429.1.22.3.1.1.63 | hdmScTxPwrLvlApplied | 0 | 0 | This object configures where the power level is applied. It applies to S-register S81.0. Default=inputToFarEndOfCodec(1). |
| 1.3.6.1.4.1.429.1.22.3.1.1.64 | hdmScPiafs | 0 | 0 | This object is used to enable or disable PIAFS protocol. Default = enable(1). |