The Subcode for ICMP Protocol.
This field is valid only if the aniDevFilterIpProtocol is
set to ICMP or not specified by the user.
If this field is specified then aniDevFilterIcmpMsgType
should already be specified. The values allowed for ICMP Code
depend on aniDevFilterIcmpMsgType.
Refer to the description under aniDevFilterIcmpMsgType for a
detail list of values.
Parsed from file DEVFILTER-MIB.mib
Module: DEVFILTER-MIB
aniDevFilterIcmpSubcode OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The Subcode for ICMP Protocol. This field is valid only if the aniDevFilterIpProtocol is set to ICMP or not specified by the user. If this field is specified then aniDevFilterIcmpMsgType should already be specified. The values allowed for ICMP Code depend on aniDevFilterIcmpMsgType. Refer to the description under aniDevFilterIcmpMsgType for a detail list of values. " ::= { aniDevFilterEntry 19 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.4325.2.8.1.1.1 | aniDevFilterIfIndex | 0 | 0 | The Interface Type. On SU, only ethernet(1) and wireless-port1(2) are valid. On BSU, ethernet(1) and all configured wireless inte… |
| 1.3.6.1.4.1.4325.2.8.1.1.2 | aniDevFilterIdentifier | 0 | 0 | A unique number which identifies the filtering rule. |
| 1.3.6.1.4.1.4325.2.8.1.1.3 | aniDevFilterName | 0 | 0 | A name which identifies the filtering rule. |
| 1.3.6.1.4.1.4325.2.8.1.1.4 | aniDevFilterPriority | 0 | 0 | The priority for the filtering rule. It should be unique. A higher number means higher priority. |
| 1.3.6.1.4.1.4325.2.8.1.1.5 | aniDevFilterActivationState | 0 | 0 | The state of the filtering rule. |
| 1.3.6.1.4.1.4325.2.8.1.1.6 | aniDevFilterPermission | 0 | 0 | The permissions for the filtering rule. |
| 1.3.6.1.4.1.4325.2.8.1.1.7 | aniDevFilterIpProtocol | 0 | 0 | The IP protocol value. List of well known IP Protocols: Protocol Value ICMP 1 IGMP 2 TCP 6 EGP 8 UDP 17 IPIP 94 RSVP 46 GRE 47 T… |
| 1.3.6.1.4.1.4325.2.8.1.1.8 | aniDevFilterIpSaddr | 0 | 0 | The source IP address for this Filter. IP Source Address and Subnet Mask go in a pair. So if aniDevFilterIpSaddr is configured, t… |
| 1.3.6.1.4.1.4325.2.8.1.1.9 | aniDevFilterIpSmask | 0 | 0 | The Subnet mask for the source IP Address. IP Source Address and Subnet Mask go in a pair. So if aniDevFilterIpSaddr is configure… |
| 1.3.6.1.4.1.4325.2.8.1.1.10 | aniDevFilterIpDaddr | 0 | 0 | The destination IP address for this Filter. IP Destination Address and Subnet Mask go in a pair. So if aniDevFilterIpDaddr is con… |
| 1.3.6.1.4.1.4325.2.8.1.1.11 | aniDevFilterIpDmask | 0 | 0 | The Subnet mask for the destination IP Address. IP Destination Address and Subnet Mask go in a pair. So if aniDevFilterIpDaddr is… |
| 1.3.6.1.4.1.4325.2.8.1.1.12 | aniDevFilterIpSourceStart | 0 | 0 | The lowest bound value for the source port number. List of Some Well Known Ports: Application Port Ftp Data 20 Ftp Control 21 HT… |
| 1.3.6.1.4.1.4325.2.8.1.1.13 | aniDevFilterIpSourceEnd | 0 | 0 | The highest bound value for the source port number. Refer to the Well known ports list under aniIpFilterIpSourceStart description… |
| 1.3.6.1.4.1.4325.2.8.1.1.14 | aniDevFilterIpDestStart | 0 | 0 | The lowest bound value for the destination port number. Refer to the Well known ports list under aniIpFilterIpSourceStart descrip… |
| 1.3.6.1.4.1.4325.2.8.1.1.15 | aniDevFilterIpDestEnd | 0 | 0 | The highest bound value for the destination port number. Refer to the Well known ports list under aniIpFilterIpSourceStart descri… |
| 1.3.6.1.4.1.4325.2.8.1.1.16 | aniDevFilterIpOptions | 0 | 0 | The Mask value for the IP Options. No Operation (0x000001) Route Record (0x000002) Time Stamp (0x000040) MTU Probe (0x000008)… |
| 1.3.6.1.4.1.4325.2.8.1.1.17 | aniDevFilterIpSecOptions | 0 | 0 | The IP Security Value. |
| 1.3.6.1.4.1.4325.2.8.1.1.18 | aniDevFilterIcmpMsgType | 0 | 0 | The Message Type for ICMP Protocol. This field is valid only if the aniDevFilterIpProtocol is set to ICMP or not specified by the… |
| 1.3.6.1.4.1.4325.2.8.1.1.20 | aniDevFilterTcpFlags | 0 | 0 | The TCP Flags. The valid range: Urgent (0x20) Acknowledgement (0x10) Push (0x08) Reset (0x04) Sync (0x02) Sync-Ack (0x12) Finish (0x01)… |
| 1.3.6.1.4.1.4325.2.8.1.1.21 | aniDevFilterDestMacMask | 0 | 0 | The MAC address and mask value for destination. |
| 1.3.6.1.4.1.4325.2.8.1.1.22 | aniDevFilterSourceMac | 0 | 0 | The MAC Address of the source. |
| 1.3.6.1.4.1.4325.2.8.1.1.23 | aniDevFilterEnetType | 0 | 0 | The Ethernet type value in the ethernet header. The maximum length of the ethernet packet is 1500 (0x5DC). The value of the ethe… |
| 1.3.6.1.4.1.4325.2.8.1.1.24 | aniDevFilterLlcDSAP | 0 | 0 | The DSAP (Destination Service Access Point) value in LLC Header. Valid Range: 0 to 0xFF Applicable for IEEE 802.3 Frame Format on… |
| 1.3.6.1.4.1.4325.2.8.1.1.25 | aniDevFilterLlcSSAP | 0 | 0 | The SSAP (Source Service Access Point) value in LLC Header. Valid Range: 0 to 0xFF Applicable for IEEE 802.3 Frame Format only. |
| 1.3.6.1.4.1.4325.2.8.1.1.26 | aniDevFilterLlcControl | 0 | 0 | The Control Byte of the LLC Header. Valid Range: 0 to 0xFF Applicable for IEEE 802.3 Frame Format only. |
| 1.3.6.1.4.1.4325.2.8.1.1.27 | aniDevFilterLocalCode | 0 | 0 | The Local Code for SNAP ethernet type. Applicable for IEEE 802.3 Frame Format only. DSAP should be set to 0xAA, SSAP should be se… |
| 1.3.6.1.4.1.4325.2.8.1.1.28 | aniDevFilterRowStatus | 0 | 0 | This represents the state of an entry within the table. It is used to manage creation and deletion of rows. The values include: a… |
| 1.3.6.1.4.1.4325.2.8.1.1.29 | aniDevFilterUserPriorityHi | 0 | 0 | The high priority byte of the user priority. The user priority specifies the matching parameters for the IEEE 802.1P user_priorit… |
| 1.3.6.1.4.1.4325.2.8.1.1.30 | aniDevFilterUserPriorityLo | 0 | 0 | The low priority byte of the user priority. The user priority specifies the matching parameters for the IEEE 802.1P user_priority… |
| 1.3.6.1.4.1.4325.2.8.1.1.31 | aniDevFilterVlanIdStart | 0 | 0 | The lower limit for the VLAN ID. This value is used to specify the lower limit in the range. Any IEEE 802.1P packet from a custom… |
| 1.3.6.1.4.1.4325.2.8.1.1.32 | aniDevFilterVlanIdEnd | 0 | 0 | The upper limit for the VLAN ID. This value is used to specify the upper limit in the range. Any IEEE 802.1P packet from a custom… |