This group gives the BSU Multiple Subnets information.
The aniBsuSubnetConfTable is used to view and configure
subnets per wireless port.
There can be upto 1024
For a given WSS port, there can be multiple and different
subnets. This means that each subnet specified by an
Atleast one Ip Address and Subnet Mask has to be specified.
In addition to the subnet being distinct, each IP Address
must be unique too.
If clustering is disabled, then Multiple Subnets on one
WSS port should not clash with Multiple Subnets on any
other WSS port.
Clustering and multiple subnets can exists simultaneously
as long as they are not on the same WSS. If clustering is
enabled but not all WSS are clustered, then those that are
not part of the cluster can have multiple subnets.
Eg. If WSS1 and WSS2 are clustered, but WSS3 and WSS4 are
not, then WSS3 and WSS4 can have multiple subnets.
To add a new subnet to the table, first set the
aniBsuSubnetConfAddr. Next send an SNMP set request
on aniBsuSubnetConfMask.
Currently, deletion and modification of entries is not supported.
When the BSU is in Bridge mode, this multiple subnets table is
not valid and will not be displayed.
Parsed from file BSUMSUBNETS-MIB.mib
Module: BSUMSUBNETS-MIB
Vendor: Aperto Networks
Module: ANIROOT-MIB
[Automatically extracted from oidview.com]
aniBsuMultSubnets MODULE-IDENTITY LAST-UPDATED "0105091130Z" ORGANIZATION "Aperto Networks" CONTACT-INFO " Postal: Aperto Networks Inc 1637 S Main Street Milpitas, California 95035 Tel: +1 408 719 9977 " DESCRIPTION "This group gives the BSU Multiple Subnets information. The aniBsuSubnetConfTable is used to view and configure subnets per wireless port. There can be upto 1024
pairs. For a given WSS port, there can be multiple and different subnets. This means that each subnet specified by an has to be distinct. Atleast one Ip Address and Subnet Mask has to be specified. In addition to the subnet being distinct, each IP Address must be unique too. If clustering is disabled, then Multiple Subnets on one WSS port should not clash with Multiple Subnets on any other WSS port. Clustering and multiple subnets can exists simultaneously as long as they are not on the same WSS. If clustering is enabled but not all WSS are clustered, then those that are not part of the cluster can have multiple subnets. Eg. If WSS1 and WSS2 are clustered, but WSS3 and WSS4 are not, then WSS3 and WSS4 can have multiple subnets. To add a new subnet to the table, first set the aniBsuSubnetConfAddr. Next send an SNMP set request on aniBsuSubnetConfMask. Currently, deletion and modification of entries is not supported. When the BSU is in Bridge mode, this multiple subnets table is not valid and will not be displayed. " ::= { bsu 6 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.4325.3.6.1 | aniBsuSubnetConfTable | 1 | 3 | aniBsuSubnetConftable |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.4325.3.1 | aniBsuStatus | 11 | 23 | This group shows the Status Information for the BSU. The aniBsuStatusRadioTable shows the information for each radio that is con… |
| 1.3.6.1.4.1.4325.3.2 | aniBsuWirelessIf | 13 | 79 | This group contains BSU Wireless Interface information. It shows parameters for each configured Wireless Port on the BSU. It disp… |
| 1.3.6.1.4.1.4325.3.3 | aniBsuStatistics | 4 | 35 | This group contains Statistical information for the BSU. aniBsuRfStatsTable shows the RF Port level statistics. aniBsuStatsBWGrou… |
| 1.3.6.1.4.1.4325.3.4 | aniBsuClock | 7 | 7 | This module is used to configure the clock time on the BSU. BSUs need to obtain and set their current clock time at boot up. Sus … |
| 1.3.6.1.4.1.4325.3.5 | aniBsuBridge | 1 | 1 | This group allows Configuration/Viewing of Bridging and Clustering parameters for BSU. Clusters can be added and deleted using Co… |
| 1.3.6.1.4.1.4325.3.7 | aniBsuSuGroup | 4 | 62 | None |
| 1.3.6.1.4.1.4325.3.8 | aniBsuParam | 1 | 1 | This group contains other configurable parameters for the BSU. |
| 1.3.6.1.4.1.4325.3.11 | aniBsuVlan | 1 | 6 | This group shows the VLAN information for the BSU. |