The Broadcast Cutoff Rate of the switch allowing for the
control of broadcast storms. The value of this variable sets
a per second rate. If the broadcast and unknown destination
address frames being forwarded through the system surpass this
rate, they are dropped. Valid values for this parameter are
in the range (100..500000).
Parsed from file ctELS100-mib.txt
Company: None
Module: CT-ELS100-MIB
The Broadcast Cutoff Rate of the switch allowing for the
control of broadcast storms. The value of this variable sets
a per second rate. If the broadcast and unknown destination
address frames being forwarded through the system surpass this
rate, they are dropped. Valid values for this parameter are
in the range (100..500000).
Parsed from file CTELS100-NG-MIB.mib
Module: CTELS100-NG-MIB
els100SysBrcastCutoffRate OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The Broadcast Cutoff Rate of the switch allowing for the control of broadcast storms. The value of this variable sets a per second rate. If the broadcast and unknown destination address frames being forwarded through the system surpass this rate, they are dropped. Valid values for this parameter are in the range (100..500000)." ::= { els100SystemConfig 5 }
Vendor: Enterasys Networks Inc.
Module: CTELS100-NG-MIB
[Automatically extracted from oidview.com]
els100SysBrcastCutoffRate OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The Broadcast Cutoff Rate of the switch allowing for the control of broadcast storms. The value of this variable sets a per second rate. If the broadcast and unknown destination address frames being forwarded through the system surpass this rate, they are dropped. Valid values for this parameter are in the range (100..500000)." ::= { els100SystemConfig 5 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.52.1011.1.5.0 | els100SysBrcastCutoffRate | 0 | 0 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.52.1011.1.1 | els100SysSerialno | 1 | 1 | The serial number of the system. |
| 1.3.6.1.4.1.52.1011.1.2 | els100SysTftpIPAddress | 1 | 1 | The IP address of the TFTP server from which a software download is to be initiated. This variable must be set before a TFTP down… |
| 1.3.6.1.4.1.52.1011.1.3 | els100SysTftpFilename | 1 | 1 | The name of the software upgrade file residing on the TFTP server. Path information must be included in the file name. This varia… |
| 1.3.6.1.4.1.52.1011.1.4 | els100SysPowerupCount | 1 | 1 | The total number of times the system has powered up since it was shipped from the factory. |
| 1.3.6.1.4.1.52.1011.1.6 | els100SysGatewayIPAddress | 1 | 1 | The IP address of the next hop router (gateway) to which frames destined for an IP subnet different than what the system resides … |
| 1.3.6.1.4.1.52.1011.1.7 | els100SysTftpStartDownload | 1 | 1 | Start a TFTP download. A SET of this variable with the value download (1) initiates a TFTP download to upgrade the system softwar… |
| 1.3.6.1.4.1.52.1011.1.8 | els100SysBootPDhcpEnable | 1 | 1 | Enable or disable the operation of the BootP and DHCP protocols on the system. These protocols are used for automatically configu… |
| 1.3.6.1.4.1.52.1011.1.10 | els100SysReset | 1 | 1 | Initiate a software reset of the system. |
| 1.3.6.1.4.1.52.1011.1.11 | els100SysSyslogServer | 1 | 1 | The IP address of the Syslog Server. |
| 1.3.6.1.4.1.52.1011.1.12 | els100SysLowestSyslogSeverity | 1 | 1 | The Lowest Syslog Severity Level. All logs with the same or higher severity will be delivered. Note: higher severity has lower nu… |
| 1.3.6.1.4.1.52.1011.1.13 | els100SysComPortEnable | 1 | 1 | The administrative state of the Com Port. |
| 1.3.6.1.4.1.52.1011.1.14 | els100SysBoardID | 1 | 1 | The system board ID. |