This variable indicates whether this interface operates in half duplex
full duplex or auto negotiation mode.
Parsed from file Vgate.txt
Company: None
Module: RND-MIB
This variable indicates whether this interface operates in half duplex
full duplex or auto negotiation mode.
Parsed from file RND-MIB.mib
Module: RND-MIB
rndDuplexMode OBJECT-TYPE SYNTAX INTEGER { half(1), full(2) } ACCESS read-write STATUS mandatory DESCRIPTION " This variable indicates whether this interface operates in half duplex full duplex or auto negotiation mode." ::= { rndIfEntry 18}
Vendor: RND
Module: RADWARE-MIB
[Automatically extracted from oidview.com]
rndDuplexMode OBJECT-TYPE SYNTAX INTEGER { half(1), full(2) } ACCESS read-write STATUS mandatory DESCRIPTION " This variable indicates whether this interface operates in half duplex full duplex or auto negotiation mode." ::= { rndIfEntry 18}
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.89.4.1.1.1 | rndIfIndex | 0 | 0 | Index to the RND Interface Table. The interface defined by a particular value of this index is the same interface as identified b… |
| 1.3.6.1.4.1.89.4.1.1.2 | rndIfBoardNum | 0 | 0 | The interface defined by this entry correspTnds to the board defined by the same value of rndSlotBoardNum in the rndSlotTab. |
| 1.3.6.1.4.1.89.4.1.1.3 | rndIfNetAddress | 0 | 0 | The IP address of the interface defined by the particular value of rndIfIndex. |
| 1.3.6.1.4.1.89.4.1.1.4 | rndIfStatus | 0 | 0 | The current status of the interface. |
| 1.3.6.1.4.1.89.4.1.1.5 | rndIfClockType | 0 | 0 | rndIfClockType defines the type of clock each interface uses: internal or external. |
| 1.3.6.1.4.1.89.4.1.1.6 | rndIfBaudRate | 0 | 0 | Defines the baud rate of use by the interface. The valid rates are determined by the type of the media for which this baud rate i… |
| 1.3.6.1.4.1.89.4.1.1.7 | rndIfCost | 0 | 0 | This variable assigns a transmission cost to the interface (channel or LAN). These costs are used in Level II routing. The costs … |
| 1.3.6.1.4.1.89.4.1.1.8 | rndIfCompression | 0 | 0 | Defines whether data compression is enabled or disabled for the interface. |
| 1.3.6.1.4.1.89.4.1.1.9 | rndIfCompressionStatus | 0 | 0 | Defines the status of the compression component: not-inserted - Compression component is not in the device active - Compressi… |
| 1.3.6.1.4.1.89.4.1.1.10 | rndIfCompressionRate | 0 | 0 | Percentage of compression. This variable applies only if rndCompressionStatus is active. |
| 1.3.6.1.4.1.89.4.1.1.11 | rndIfLATCompression | 0 | 0 | Enable/Disable the LAT Compression. |
| 1.3.6.1.4.1.89.4.1.1.12 | rndIfCompressionType | 0 | 0 | This parameter indicates the type of compression option available in the device. none(1) - indicates that there is no compre… |
| 1.3.6.1.4.1.89.4.1.1.13 | rndIfFilterMode | 0 | 0 | This parameter indicates the type of filtering in the device. |
| 1.3.6.1.4.1.89.4.1.1.14 | rndIfChannelType | 0 | 0 | The type of the WAN channel |
| 1.3.6.1.4.1.89.4.1.1.15 | rndIfBridge | 0 | 0 | This variable indicates whether this interface forward Layer II pakages. |
| 1.3.6.1.4.1.89.4.1.1.16 | rndHighPriorityIf | 0 | 0 | This variable indicates whether this interface will forward pakages that fit HighPriority set by the manager. |
| 1.3.6.1.4.1.89.4.1.1.17 | rndWanHeader | 0 | 0 | This variable indicates the RND WAN header type used for frames which pass through this interface. 'regular' specifies a 14 byte… |