A value that indicates the connection policies
enforced at the station. A station sets the
corresponding policy for each of the connection
types that it rejects. The letter designations, X
and Y, in the 'rejectX-Y' names have the following
significance: X represents the PC-Type of the
local PORT and Y represents a PC-Neighbor in the
evaluation of Connection-Policy (PC-Type, PC-
Neighbor) that is done to determine the setting of
T-Val(3) in the PC-Signaling sequence (refer to
ANSI Section 9.6.3).
The value is a sum. This value initially takes
the value zero, then for each of the connection
policies currently enforced on the node, 2 raised
to a power is added to the sum. The powers are
according to the following table:
Policy Power
rejectA-A 0
rejectA-B 1
rejectA-S 2
rejectA-M 3
rejectB-A 4
rejectB-B 5
rejectB-S 6
rejectB-M 7
rejectS-A 8
rejectS-B 9
rejectS-S 10
rejectS-M 11
rejectM-A 12
rejectM-B 13
rejectM-S 14
rejectM-M 15
Implementors should note that the polarity of
these bits is different in different places in an
SMT system. Implementors should take appropriate
care.
snmpFddiSMTConnectionPolicy OBJECT-TYPE
SYNTAX INTEGER (0..65535)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"A value that indicates the connection policies
enforced at the station. A station sets the
corresponding policy for each of the connection
types that it rejects. The letter designations, X
and Y, in the
ejectX-Y names have the following
significance: X represents the PC-Type of the
local PORT and Y represents a PC-Neighbor in the
evaluation of Connection-Policy (PC-Type, PC-
Neighbor) that is done to determine the setting of
T-Val(3) in the PC-Signaling sequence (refer to
ANSI Section 9.6.3).
The value is a sum. This value initially takes
the value zero, then for each of the connection
policies currently enforced on the node, 2 raised
to a power is added to the sum. The powers are
according to the following table:
Policy Power
rejectA-A 0
rejectA-B 1
rejectA-S 2
rejectA-M 3
rejectB-A 4
rejectB-B 5
rejectB-S 6
rejectB-M 7
rejectS-A 8
rejectS-B 9
rejectS-S 10
rejectS-M 11
rejectM-A 12
rejectM-B 13
rejectM-S 14
rejectM-M 15
Implementors should note that the polarity of
these bits is different in different places in an
SMT system. Implementors should take appropriate
care."
REFERENCE
"ANSI { fddiSMT 27 }"
View at oid-info.com
A value that indicates the connection policies
enforced at the station. A station sets the
corresponding policy for each of the connection
types that it rejects. The letter designations, X
and Y, in the 'rejectX-Y' names have the following
significance: X represents the PC-Type of the
local PORT and Y represents a PC-Neighbor in the
evaluation of Connection-Policy (PC-Type, PC-
Neighbor) that is done to determine the setting of
T-Val(3) in the PC-Signaling sequence (refer to
ANSI Section 9.6.3).
The value is a sum. This value initially takes
the value zero, then for each of the connection
policies currently enforced on the node, 2 raised
to a power is added to the sum. The powers are
according to the following table:
Policy Power
rejectA-A 0
rejectA-B 1
rejectA-S 2
rejectA-M 3
rejectB-A 4
rejectB-B 5
rejectB-S 6
rejectB-M 7
rejectS-A 8
rejectS-B 9
rejectS-S 10
rejectS-M 11
rejectM-A 12
rejectM-B 13
rejectM-S 14
rejectM-M 15
Implementors should note that the polarity of
these bits is different in different places in an
SMT system. Implementors should take appropriate
care.
Parsed from file ph3-fddi.mib.txt
Company: None
Module: RFC1285-MIB
A value that indicates the connection policies
enforced at the station. A station sets the
corresponding policy for each of the connection
types that it rejects. The letter designations, X
and Y, in the 'rejectX-Y' names have the following
significance: X represents the PC-Type of the
local PORT and Y represents a PC-Neighbor in the
evaluation of Connection-Policy (PC-Type, PC-
Neighbor) that is done to determine the setting of
T-Val(3) in the PC-Signaling sequence (refer to
ANSI Section 9.6.3).
The value is a sum. This value initially takes
the value zero, then for each of the connection
policies currently enforced on the node, 2 raised
to a power is added to the sum. The powers are
according to the following table:
Policy Power
rejectA-A 0
rejectA-B 1
rejectA-S 2
rejectA-M 3
rejectB-A 4
rejectB-B 5
rejectB-S 6
rejectB-M 7
rejectS-A 8
rejectS-B 9
rejectS-S 10
rejectS-M 11
rejectM-A 12
rejectM-B 13
rejectM-S 14
rejectM-M 15
Implementors should note that the polarity of
these bits is different in different places in an
SMT system. Implementors should take appropriate
care.
Parsed from file RFC1285-MIB.mib
Module: RFC1285-MIB
snmpFddiSMTConnectionPolicy OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "A value that indicates the connection policies enforced at the station. A station sets the corresponding policy for each of the connection types that it rejects. The letter designations, X and Y, in the 'rejectX-Y' names have the following significance: X represents the PC-Type of the local PORT and Y represents a PC-Neighbor in the evaluation of Connection-Policy (PC-Type, PC- Neighbor) that is done to determine the setting of T-Val(3) in the PC-Signaling sequence (refer to ANSI Section 9.6.3). The value is a sum. This value initially takes the value zero, then for each of the connection policies currently enforced on the node, 2 raised to a power is added to the sum. The powers are according to the following table: Policy Power rejectA-A 0 rejectA-B 1 rejectA-S 2 rejectA-M 3 rejectB-A 4 rejectB-B 5 rejectB-S 6 rejectB-M 7 rejectS-A 8 rejectS-B 9 rejectS-S 10 rejectS-M 11 rejectM-A 12 rejectM-B 13 rejectM-S 14 rejectM-M 15 Implementors should note that the polarity of these bits is different in different places in an SMT system. Implementors should take appropriate care." REFERENCE "ANSI { fddiSMT 27 }" ::= { snmpFddiSMTEntry 12 }
Automatically extracted from RFC1285
snmpFddiSMTConnectionPolicy OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "A value that indicates the connection policies enforced at the station. A station sets the corresponding policy for each of the connection types that it rejects. The letter designations, X and Y, in the 'rejectX-Y' names have the following significance: X represents the PC-Type of the local PORT and Y represents a PC-Neighbor in the evaluation of Connection-Policy (PC-Type, PC- Neighbor) that is done to determine the setting of T-Val(3) in the PC-Signaling sequence (refer to ANSI Section 9.6.3). The value is a sum. This value initially takes the value zero, then for each of the connection policies currently enforced on the node, 2 raised to a power is added to the sum. The powers are according to the following table: Policy Power rejectA-A 0 rejectA-B 1 rejectA-S 2 rejectA-M 3 rejectB-A 4 rejectB-B 5 rejectB-S 6 rejectB-M 7 rejectS-A 8 rejectS-B 9 rejectS-S 10 rejectS-M 11 rejectM-A 12 rejectM-B 13 rejectM-S 14 rejectM-M 15 Implementors should note that the polarity of these bits is different in different places in an SMT system. Implementors should take appropriate care." REFERENCE "ANSI { fddiSMT 27 }" ::= { snmpFddiSMTEntry 12 }
snmpFddiSMTConnectionPolicy OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "A value that indicates the connection policies enforced at the station. A station sets the corresponding policy for each of the connection types that it rejects. The letter designations, X and Y, in the 'rejectX-Y' names have the following significance: X represents the PC-Type of the local PORT and Y represents a PC-Neighbor in the evaluation of Connection-Policy (PC-Type, PC- Neighbor) that is done to determine the setting of T-Val(3) in the PC-Signaling sequence (refer to ANSI Section 9.6.3). The value is a sum. This value initially takes the value zero, then for each of the connection policies currently enforced on the node, 2 raised to a power is added to the sum. The powers are according to the following table: Policy Power rejectA-A 0 rejectA-B 1 rejectA-S 2 rejectA-M 3 rejectB-A 4 rejectB-B 5 rejectB-S 6 rejectB-M 7 rejectS-A 8 rejectS-B 9 rejectS-S 10 rejectS-M 11 rejectM-A 12 rejectM-B 13 rejectM-S 14 rejectM-M 15 Implementors should note that the polarity of these bits is different in different places in an SMT system. Implementors should take appropriate care." REFERENCE "ANSI { fddiSMT 27 }" ::= { snmpFddiSMTEntry 12 }
Internet Assigned Numbers Authority
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.15.1.2.1.1 | snmpFddiSMTIndex | 0 | 0 | A unique value for each SMT. Its value ranges between 1 and the value of snmpFddiSMTNumber. The value for each SMT must remain … |
| 1.3.6.1.2.1.10.15.1.2.1.2 | snmpFddiSMTStationId | 0 | 0 | Uniquely identifies an FDDI station. |
| 1.3.6.1.2.1.10.15.1.2.1.3 | snmpFddiSMTOpVersionId | 0 | 0 | The version that this station is using for its operation (refer to ANSI 7.1.2.2). |
| 1.3.6.1.2.1.10.15.1.2.1.4 | snmpFddiSMTHiVersionId | 0 | 0 | The highest version of SMT that this station supports (refer to ANSI 7.1.2.2). |
| 1.3.6.1.2.1.10.15.1.2.1.5 | snmpFddiSMTLoVersionId | 0 | 0 | The lowest version of SMT that this station supports (refer to ANSI 7.1.2.2). |
| 1.3.6.1.2.1.10.15.1.2.1.6 | snmpFddiSMTMACCt | 0 | 0 | The number of MACs in the station or concentrator. |
| 1.3.6.1.2.1.10.15.1.2.1.7 | snmpFddiSMTNonMasterCt | 0 | 0 | The number of Non Master PORTs (A, B, or S PORTs) in the station or concentrator. |
| 1.3.6.1.2.1.10.15.1.2.1.8 | snmpFddiSMTMasterCt | 0 | 0 | The number of Master PORTs in a node. If the node is not a concentrator, the value is zero. |
| 1.3.6.1.2.1.10.15.1.2.1.9 | snmpFddiSMTPathsAvailable | 0 | 0 | A value that indicates the PATH types available in the station. The value is a sum. This value initially takes the value zero, th… |
| 1.3.6.1.2.1.10.15.1.2.1.10 | snmpFddiSMTConfigCapabilities | 0 | 0 | A value that indicates capabilities that are present in the node. If 'holdAvailable' is present, this indicates support of the o… |
| 1.3.6.1.2.1.10.15.1.2.1.11 | snmpFddiSMTConfigPolicy | 0 | 0 | A value that indicates the configuration policies currently enforced in the node (refer to ANSI SMT 9.4.3.2). The 'configuration… |
| 1.3.6.1.2.1.10.15.1.2.1.13 | snmpFddiSMTTNotify | 0 | 0 | The timer used in the Neighbor Notification protocol, reported in seconds and ranging from 2 to 30 seconds (refer to ANSI SMT 8.3… |
| 1.3.6.1.2.1.10.15.1.2.1.14 | snmpFddiSMTStatusReporting | 0 | 0 | Indicates whether the node implements the Status Reporting Protocol. This object is included for compatibility with products tha… |
| 1.3.6.1.2.1.10.15.1.2.1.15 | snmpFddiSMTECMState | 0 | 0 | Indicates the current state of the ECM state machine (refer to ANSI SMT 9.5.2). |
| 1.3.6.1.2.1.10.15.1.2.1.16 | snmpFddiSMTCFState | 0 | 0 | The attachment configuration for the station or concentrator (refer to ANSI SMT 9.7.4.3). |
| 1.3.6.1.2.1.10.15.1.2.1.17 | snmpFddiSMTHoldState | 0 | 0 | This value indicates the current state of the Hold function. The values are determined as follows: 'holding-prm' is set if the … |
| 1.3.6.1.2.1.10.15.1.2.1.18 | snmpFddiSMTRemoteDisconnectFlag | 0 | 0 | A flag indicating that the station was remotely disconnected from the network. A station requires a Connect Action (SM_CM_CONNEC… |
| 1.3.6.1.2.1.10.15.1.2.1.19 | snmpFddiSMTStationAction | 0 | 0 | This object, when read, always returns a value of other(1). The behavior of setting this variable to each of the acceptable valu… |