This variable indicates the Line Status of the
interface. It contains loopback, failure, re-
ceived 'alarm' and transmitted 'alarm' infor-
mation.
The dsx1LineStatus is a bit map represented as a sum,
therefore, it can represent multiple failures (alarms) and
a LoopbackState simultaneously.
dsx1NoAlarm should be set if and only if no other flag is
set.
If the dsx1LoopbackState bit is set, the loopback in ef-
fect can be determined from the dsx1LoopbackConfig object.
The various bit positions are:
1 dsx1NoAlarm No Alarm Present
2 dsx1RcvFarEndLOF Far end LOF (a.k.a., Yellow Alarm)
4 dsx1XmtFarEndLOF Near end sending LOF Indication
8 dsx1RcvAIS Far end sending AIS
16 dsx1XmtAIS Near end sending AIS
32 dsx1LossOfFrame Near end LOF (a.k.a., Red Alarm)
64 dsx1LossOfSignal Near end Loss Of Signal
128 dsx1LoopbackState Near end is looped
256 dsx1T16AIS E1 TS16 AIS
512 dsx1RcvFarEndLOMF Far End Sending TS16 LOMF
1024 dsx1XmtFarEndLOMF Near End Sending TS16 LOMF
2048 dsx1RcvTestCode Near End detects a test code
4096 dsx1OtherFailure any line status not defined here
Parsed from file RFC1406-MIB.mib
Module: RFC1406-MIB
This variable indicates the Line Status of the
interface. It contains loopback, failure,
received 'alarm' and transmitted 'alarms
information.
The dsx1LineStatus is a bit map represented as a
sum, therefore, it can represent multiple failures
(alarms) and a LoopbackState simultaneously.
dsx1NoAlarm must be set if and only if no other
flag is set.
If the dsx1loopbackState bit is set, the loopback
in effect can be determined from the
dsx1loopbackConfig object.
The various bit positions are:
1 dsx1NoAlarm No alarm present
2 dsx1RcvFarEndLOF Far end LOF (a.k.a., Yellow Alarm)
4 dsx1XmtFarEndLOF Near end sending LOF Indication
8 dsx1RcvAIS Far end sending AIS
16 dsx1XmtAIS Near end sending AIS
32 dsx1LossOfFrame Near end LOF (a.k.a., Red Alarm)
64 dsx1LossOfSignal Near end Loss Of Signal
128 dsx1LoopbackState Near end is looped
256 dsx1T16AIS E1 TS16 AIS
512 dsx1RcvFarEndLOMF Far End Sending TS16 LOMF
1024 dsx1XmtFarEndLOMF Near End Sending TS16 LOMF
2048 dsx1RcvTestCode Near End detects a test code
4096 dsx1OtherFailure any line status not defined here
8192 dsx1UnavailSigState Near End in Unavailable Signal
State
16384 dsx1NetEquipOOS Carrier Equipment Out of Service
32768 dsx1RcvPayloadAIS DS2 Payload AIS
65536 dsx1Ds2PerfThreshold DS2 Performance Threshold
Exceeded
dsx1LineStatus OBJECT-TYPE
SYNTAX INTEGER (1..131071)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates the Line Status of the
interface. It contains loopback, failure,
received alarm and transmitted alarms
information.
The dsx1LineStatus is a bit map represented as a
sum, therefore, it can represent multiple failures
(alarms) and a LoopbackState simultaneously.
dsx1NoAlarm must be set if and only if no other
flag is set.
If the dsx1loopbackState bit is set, the loopback
in effect can be determined from the
dsx1loopbackConfig object.
The various bit positions are:
1 dsx1NoAlarm No alarm present
2 dsx1RcvFarEndLOF Far end LOF (a.k.a., Yellow Alarm)
4 dsx1XmtFarEndLOF Near end sending LOF Indication
8 dsx1RcvAIS Far end sending AIS
16 dsx1XmtAIS Near end sending AIS
32 dsx1LossOfFrame Near end LOF (a.k.a., Red Alarm)
64 dsx1LossOfSignal Near end Loss Of Signal
128 dsx1LoopbackState Near end is looped
256 dsx1T16AIS E1 TS16 AIS
512 dsx1RcvFarEndLOMF Far End Sending TS16 LOMF
1024 dsx1XmtFarEndLOMF Near End Sending TS16 LOMF
2048 dsx1RcvTestCode Near End detects a test code
4096 dsx1OtherFailure any line status not defined here
8192 dsx1UnavailSigState Near End in Unavailable Signal
State
16384 dsx1NetEquipOOS Carrier Equipment Out of Service
32768 dsx1RcvPayloadAIS DS2 Payload AIS
65536 dsx1Ds2Perfthreshold DS2 Performance Threshold
Exceeded"
View at oid-info.com
This variable indicates the Line Status of the
interface. It contains loopback, failure, re-
ceived 'alarm' and transmitted 'alarm' infor-
mation.
The dsx1LineStatus is a bit map represented as a sum,
therefore, it can represent multiple failures (alarms) and
a LoopbackState simultaneously.
dsx1NoAlarm should be set if and only if no other flag is
set.
If the dsx1LoopbackState bit is set, the loopback in ef-
fect can be determined from the dsx1LoopbackConfig object.
The various bit positions are:
1 dsx1NoAlarm No Alarm Present
2 dsx1RcvFarEndLOF Far end LOF (a.k.a., Yellow Alarm)
4 dsx1XmtFarEndLOF Near end sending LOF Indication
8 dsx1RcvAIS Far end sending AIS
16 dsx1XmtAIS Near end sending AIS
32 dsx1LossOfFrame Near end LOF (a.k.a., Red Alarm)
64 dsx1LossOfSignal Near end Loss Of Signal
128 dsx1LoopbackState Near end is looped
256 dsx1T16AIS E1 TS16 AIS
512 dsx1RcvFarEndLOMF Far End Sending TS16 LOMF
1024 dsx1XmtFarEndLOMF Near End Sending TS16 LOMF
2048 dsx1RcvTestCode Near End detects a test code
4096 dsx1OtherFailure any line status not defined here
Parsed from file mib_txt_12_3_1_5.txt
Company: None
Module: ACC-MIB
This variable indicates the Line Status of the
interface. It contains loopback, failure,
received 'alarm' and transmitted 'alarms
information.
The dsx1LineStatus is a bit map represented as a
sum, therefore, it can represent multiple failures
(alarms) and a LoopbackState simultaneously.
dsx1NoAlarm must be set if and only if no other
flag is set.
If the dsx1loopbackState bit is set, the loopback
in effect can be determined from the
dsx1loopbackConfig object.
The various bit positions are:
1 dsx1NoAlarm No alarm present
2 dsx1RcvFarEndLOF Far end LOF (a.k.a., Yellow Alarm)
4 dsx1XmtFarEndLOF Near end sending LOF Indication
8 dsx1RcvAIS Far end sending AIS
16 dsx1XmtAIS Near end sending AIS
32 dsx1LossOfFrame Near end LOF (a.k.a., Red Alarm)
64 dsx1LossOfSignal Near end Loss Of Signal
128 dsx1LoopbackState Near end is looped
256 dsx1T16AIS E1 TS16 AIS
512 dsx1RcvFarEndLOMF Far End Sending TS16 LOMF
1024 dsx1XmtFarEndLOMF Near End Sending TS16 LOMF
2048 dsx1RcvTestCode Near End detects a test code
4096 dsx1OtherFailure any line status not defined here
8192 dsx1UnavailSigState Near End in Unavailable Signal
State
16384 dsx1NetEquipOOS Carrier Equipment Out of Service
32768 dsx1RcvPayloadAIS DS2 Payload AIS
65536 dsx1Ds2PerfThreshold DS2 Performance Threshold
Exceeded
dsx1LineStatus OBJECT-TYPE SYNTAX INTEGER (1..8191) ACCESS read-only STATUS mandatory DESCRIPTION "This variable indicates the Line Status of the interface. It contains loopback, failure, re- ceived 'alarm' and transmitted 'alarm' infor- mation. The dsx1LineStatus is a bit map represented as a sum, therefore, it can represent multiple failures (alarms) and a LoopbackState simultaneously. dsx1NoAlarm should be set if and only if no other flag is set. If the dsx1LoopbackState bit is set, the loopback in ef- fect can be determined from the dsx1LoopbackConfig object. The various bit positions are: 1 dsx1NoAlarm No Alarm Present 2 dsx1RcvFarEndLOF Far end LOF (a.k.a., Yellow Alarm) 4 dsx1XmtFarEndLOF Near end sending LOF Indication 8 dsx1RcvAIS Far end sending AIS 16 dsx1XmtAIS Near end sending AIS 32 dsx1LossOfFrame Near end LOF (a.k.a., Red Alarm) 64 dsx1LossOfSignal Near end Loss Of Signal 128 dsx1LoopbackState Near end is looped 256 dsx1T16AIS E1 TS16 AIS 512 dsx1RcvFarEndLOMF Far End Sending TS16 LOMF 1024 dsx1XmtFarEndLOMF Near End Sending TS16 LOMF 2048 dsx1RcvTestCode Near End detects a test code 4096 dsx1OtherFailure any line status not defined here" ::= { dsx1ConfigEntry 10 }
dsx1LineStatus OBJECT-TYPE SYNTAX INTEGER(1..131071) ACCESS read-only STATUS mandatory DESCRIPTION "This variable indicates the Line Status of the interface. It contains loopback, failure, received 'alarm' and transmitted 'alarms information. The dsx1LineStatus is a bit map represented as a sum, therefore, it can represent multiple failures (alarms) and a LoopbackState simultaneously. dsx1NoAlarm must be set if and only if no other flag is set. If the dsx1loopbackState bit is set, the loopback in effect can be determined from the dsx1loopbackConfig object. The various bit positions are: 1 dsx1NoAlarm No alarm present 2 dsx1RcvFarEndLOF Far end LOF (a.k.a., Yellow Alarm) 4 dsx1XmtFarEndLOF Near end sending LOF Indication 8 dsx1RcvAIS Far end sending AIS 16 dsx1XmtAIS Near end sending AIS 32 dsx1LossOfFrame Near end LOF (a.k.a., Red Alarm) 64 dsx1LossOfSignal Near end Loss Of Signal 128 dsx1LoopbackState Near end is looped 256 dsx1T16AIS E1 TS16 AIS 512 dsx1RcvFarEndLOMF Far End Sending TS16 LOMF 1024 dsx1XmtFarEndLOMF Near End Sending TS16 LOMF 2048 dsx1RcvTestCode Near End detects a test code 4096 dsx1OtherFailure any line status not defined here 8192 dsx1UnavailSigState Near End in Unavailable Signal State 16384 dsx1NetEquipOOS Carrier Equipment Out of Service 32768 dsx1RcvPayloadAIS DS2 Payload AIS 65536 dsx1Ds2PerfThreshold DS2 Performance Threshold Exceeded" ::= { dsx1ConfigEntry 10 }
Automatically extracted from Cisco "SNMP v2 MIBs".
dsx1LineStatus OBJECT-TYPE SYNTAX INTEGER (1..8191) ACCESS read-only STATUS mandatory ::= { dsx1ConfigEntry 10 }
dsx1LineStatus OBJECT-TYPE SYNTAX INTEGER (1..131071) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the Line Status of the interface. It contains loopback, failure, received 'alarm' and transmitted 'alarms information. The dsx1LineStatus is a bit map represented as a sum, therefore, it can represent multiple failures (alarms) and a LoopbackState simultaneously. dsx1NoAlarm must be set if and only if no other flag is set. If the dsx1loopbackState bit is set, the loopback in effect can be determined from the dsx1loopbackConfig object. The various bit positions are: 1 dsx1NoAlarm No alarm present 2 dsx1RcvFarEndLOF Far end LOF (a.k.a., Yellow Alarm) 4 dsx1XmtFarEndLOF Near end sending LOF Indication 8 dsx1RcvAIS Far end sending AIS 16 dsx1XmtAIS Near end sending AIS 32 dsx1LossOfFrame Near end LOF (a.k.a., Red Alarm) 64 dsx1LossOfSignal Near end Loss Of Signal 128 dsx1LoopbackState Near end is looped 256 dsx1T16AIS E1 TS16 AIS 512 dsx1RcvFarEndLOMF Far End Sending TS16 LOMF 1024 dsx1XmtFarEndLOMF Near End Sending TS16 LOMF 2048 dsx1RcvTestCode Near End detects a test code 4096 dsx1OtherFailure any line status not defined here 8192 dsx1UnavailSigState Near End in Unavailable Signal State 16384 dsx1NetEquipOOS Carrier Equipment Out of Service 32768 dsx1RcvPayloadAIS DS2 Payload AIS 65536 dsx1Ds2PerfThreshold DS2 Performance Threshold Exceeded" ::= { dsx1ConfigEntry 10 }
Internet Assigned Numbers Authority
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.18.6.1.1 | dsx1LineIndex | 0 | 0 | This object is the identifier of a DS1 Inter- face on a managed device. If there is an ifEn- try that is directly associated wi… |
| 1.3.6.1.2.1.10.18.6.1.2 | dsx1IfIndex | 0 | 0 | This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
| 1.3.6.1.2.1.10.18.6.1.3 | dsx1TimeElapsed | 0 | 0 | The number of seconds that have elapsed since the beginning of the current error-measurement period. |
| 1.3.6.1.2.1.10.18.6.1.4 | dsx1ValidIntervals | 0 | 0 | The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought o… |
| 1.3.6.1.2.1.10.18.6.1.5 | dsx1LineType | 0 | 0 | This variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits… |
| 1.3.6.1.2.1.10.18.6.1.6 | dsx1LineCoding | 0 | 0 | This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its chara… |
| 1.3.6.1.2.1.10.18.6.1.7 | dsx1SendCode | 0 | 0 | This variable indicates what type of code is being sent across the DS1 interface by the dev- ice. The values mean: dsx1SendNoCo… |
| 1.3.6.1.2.1.10.18.6.1.8 | dsx1CircuitIdentifier | 0 | 0 | This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting. |
| 1.3.6.1.2.1.10.18.6.1.9 | dsx1LoopbackConfig | 0 | 0 | This variable represents the loopback confi- guration of the DS1 interface. Agents support- ing read/write access should retur… |
| 1.3.6.1.2.1.10.18.6.1.11 | dsx1SignalMode | 0 | 0 | 'none' indicates that no bits are reserved for signaling on this channel. 'robbedBit' indicates that T1 Robbed Bit Sig- naling is… |
| 1.3.6.1.2.1.10.18.6.1.12 | dsx1TransmitClockSource | 0 | 0 | The source of Tranmit Clock. 'loopTiming' indicates that the recovered re- ceive clock is used as the transmit clock. 'localTimin… |
| 1.3.6.1.2.1.10.18.6.1.13 | dsx1Fdl | 0 | 0 | This bitmap describes the use of the facili- ties data link, and is the sum of the capabili- ties: 'other' indicates that a prot… |
| 1.3.6.1.2.1.10.18.6.1.14 | dsx1InvalidIntervals | 0 | 0 | The number of intervals for which no valid data is available. |
| 1.3.6.1.2.1.10.18.6.1.15 | dsx1LineLength | 0 | 0 | The length of the ds1 line in meters. This objects provides information for line build out circuitry if it exists and can use thi… |
| 1.3.6.1.2.1.10.18.6.1.16 | dsx1LineStatusLastChange | 0 | 0 | The value of MIB II's sysUpTime object at the time this DS1 entered its current line status state. If the current state was ente… |
| 1.3.6.1.2.1.10.18.6.1.17 | dsx1LineStatusChangeTrapEnable | 0 | 0 | Indicates whether dsx1LineStatusChange traps should be generated for this interface. |
| 1.3.6.1.2.1.10.18.6.1.18 | dsx1LoopbackStatus | 0 | 0 | This variable represents the current state of the loopback on the DS1 interface. It contains information about loopbacks establi… |
| 1.3.6.1.2.1.10.18.6.1.19 | dsx1Ds1ChannelNumber | 0 | 0 | This variable represents the channel number of the DS1/E1 on its parent Ds2/E2 or DS3/E3. A value of 0 indicated this DS1/E1 doe… |
| 1.3.6.1.2.1.10.18.6.1.20 | dsx1Channelization | 0 | 0 | Indicates whether this ds1/e1 is channelized or unchannelized. The value of enabledDs0 indicates that this is a DS1 channelized … |
| 1.3.6.1.2.1.10.18.6.1.21 | dsx1LineMode | 0 | 0 | This setting puts the T1 framer into either long haul (CSU) mode or short haul (DSU) mode. |
| 1.3.6.1.2.1.10.18.6.1.22 | dsx1LineBuildOut | 0 | 0 | Attenuation setting for T1 framer in long haul (CSU) mode. The optional values are: -7.5dB, -15dB, -22.5dB and 0dB. |
| 1.3.6.1.2.1.10.18.6.1.23 | dsx1LineImpedance | 0 | 0 | dsx1LineImpedance OBJECT-TYPE SYNTAX INTEGER { notApplicable(1), unbalanced75ohms(2), balanced100ohms(3), balanced120ohms(4) } … |
| 1.3.6.1.2.1.10.18.6.1.100 | dsx1LineBuildOut | 0 | 0 | None |
| 1.3.6.1.2.1.10.18.6.1.101 | dsx1PerformanceReport | 0 | 0 | None |