dsx1LineImpedance OBJECT-TYPE
SYNTAX INTEGER {
notApplicable(1),
unbalanced75ohms(2),
balanced100ohms(3),
balanced120ohms(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Nominal line impedance. For T1 and J1 lines, the
value is typically balanced100ohms(3). For E1
lines, the value is typically unbalanced75ohms(2)
and balanced120ohms(4). When this object does not
apply, or when the appropriate value is not known,
the value should be set to notApplicable(1)."
View at oid-info.com
Automatically extracted from RFC4805
Internet Assigned Numbers Authority
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.18.6.1.1 | dsx1LineIndex | 0 | 0 | This object is the identifier of a DS1 Inter- face on a managed device. If there is an ifEn- try that is directly associated wi… |
| 1.3.6.1.2.1.10.18.6.1.2 | dsx1IfIndex | 0 | 0 | This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
| 1.3.6.1.2.1.10.18.6.1.3 | dsx1TimeElapsed | 0 | 0 | The number of seconds that have elapsed since the beginning of the current error-measurement period. |
| 1.3.6.1.2.1.10.18.6.1.4 | dsx1ValidIntervals | 0 | 0 | The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought o… |
| 1.3.6.1.2.1.10.18.6.1.5 | dsx1LineType | 0 | 0 | This variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits… |
| 1.3.6.1.2.1.10.18.6.1.6 | dsx1LineCoding | 0 | 0 | This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its chara… |
| 1.3.6.1.2.1.10.18.6.1.7 | dsx1SendCode | 0 | 0 | This variable indicates what type of code is being sent across the DS1 interface by the dev- ice. The values mean: dsx1SendNoCo… |
| 1.3.6.1.2.1.10.18.6.1.8 | dsx1CircuitIdentifier | 0 | 0 | This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting. |
| 1.3.6.1.2.1.10.18.6.1.9 | dsx1LoopbackConfig | 0 | 0 | This variable represents the loopback confi- guration of the DS1 interface. Agents support- ing read/write access should retur… |
| 1.3.6.1.2.1.10.18.6.1.10 | dsx1LineStatus | 0 | 0 | This variable indicates the Line Status of the interface. It contains loopback, failure, re- ceived 'alarm' and transmitted 'a… |
| 1.3.6.1.2.1.10.18.6.1.11 | dsx1SignalMode | 0 | 0 | 'none' indicates that no bits are reserved for signaling on this channel. 'robbedBit' indicates that T1 Robbed Bit Sig- naling is… |
| 1.3.6.1.2.1.10.18.6.1.12 | dsx1TransmitClockSource | 0 | 0 | The source of Tranmit Clock. 'loopTiming' indicates that the recovered re- ceive clock is used as the transmit clock. 'localTimin… |
| 1.3.6.1.2.1.10.18.6.1.13 | dsx1Fdl | 0 | 0 | This bitmap describes the use of the facili- ties data link, and is the sum of the capabili- ties: 'other' indicates that a prot… |
| 1.3.6.1.2.1.10.18.6.1.14 | dsx1InvalidIntervals | 0 | 0 | The number of intervals for which no valid data is available. |
| 1.3.6.1.2.1.10.18.6.1.15 | dsx1LineLength | 0 | 0 | The length of the ds1 line in meters. This objects provides information for line build out circuitry if it exists and can use thi… |
| 1.3.6.1.2.1.10.18.6.1.16 | dsx1LineStatusLastChange | 0 | 0 | The value of MIB II's sysUpTime object at the time this DS1 entered its current line status state. If the current state was ente… |
| 1.3.6.1.2.1.10.18.6.1.17 | dsx1LineStatusChangeTrapEnable | 0 | 0 | Indicates whether dsx1LineStatusChange traps should be generated for this interface. |
| 1.3.6.1.2.1.10.18.6.1.18 | dsx1LoopbackStatus | 0 | 0 | This variable represents the current state of the loopback on the DS1 interface. It contains information about loopbacks establi… |
| 1.3.6.1.2.1.10.18.6.1.19 | dsx1Ds1ChannelNumber | 0 | 0 | This variable represents the channel number of the DS1/E1 on its parent Ds2/E2 or DS3/E3. A value of 0 indicated this DS1/E1 doe… |
| 1.3.6.1.2.1.10.18.6.1.20 | dsx1Channelization | 0 | 0 | Indicates whether this ds1/e1 is channelized or unchannelized. The value of enabledDs0 indicates that this is a DS1 channelized … |
| 1.3.6.1.2.1.10.18.6.1.21 | dsx1LineMode | 0 | 0 | This setting puts the T1 framer into either long haul (CSU) mode or short haul (DSU) mode. |
| 1.3.6.1.2.1.10.18.6.1.22 | dsx1LineBuildOut | 0 | 0 | Attenuation setting for T1 framer in long haul (CSU) mode. The optional values are: -7.5dB, -15dB, -22.5dB and 0dB. |
| 1.3.6.1.2.1.10.18.6.1.100 | dsx1LineBuildOut | 0 | 0 | None |
| 1.3.6.1.2.1.10.18.6.1.101 | dsx1PerformanceReport | 0 | 0 | None |