The architecture of the APS group.
onePlusOne
The 1+1 architecture permanently bridges the working
line to the protection line.
oneToN
The 1:n architecture allows one protection channel to
protect up to n working channels. When a fault is detected
on one of the n working channels that channel is bridged
over the protection channel.
onePlusOneCompatible
This refers to 1 + 1 bidirectional switching compatible with
1:n bidirectional switching as specified in ITU-T
Recommendation G.783 (04/97) section A.3.4.1. Since this
mode necessitates bidirectional switching, apsConfigDirection
must be set to bidirectional whenever onePlusOneCompatible
is set.
onePlusOneOptimized
This refers to 1 + 1 bidirectional switching optimized
for a network using predominantly 1 + 1 bidirectional
switching as specified in ITU-T Recommendation G.783 (04/97)
section B.1. Since this mode necessitates bidirectional
switching, apsConfigDirection must be set to bidirectional
whenever onePlusOneOptimized is set.
This object may not be modified if the associated
apsConfigRowStatus object is equal to active(1).
Parsed from file APS-MIB.mib
Module: APS-MIB
Vendor: IETF RFCs
Module: APS-MIB (rfc3498-SONET-Linear-Automatic-Protection-Switching-APS.mib)
Type: TABULAR
Access: read-create
Syntax: INTEGER
Automatically extracted from www.mibdepot.com
apsConfigMode OBJECT-TYPE SYNTAX INTEGER { onePlusOne(1), oneToN(2), onePlusOneCompatible(3), onePlusOneOptimized(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The architecture of the APS group. onePlusOne The 1+1 architecture permanently bridges the working line to the protection line. oneToN The 1:n architecture allows one protection channel to protect up to n working channels. When a fault is detected on one of the n working channels that channel is bridged over the protection channel. onePlusOneCompatible This refers to 1 + 1 bidirectional switching compatible with 1:n bidirectional switching as specified in ITU-T Recommendation G.783 (04/97) section A.3.4.1. Since this mode necessitates bidirectional switching, apsConfigDirection must be set to bidirectional whenever onePlusOneCompatible is set. onePlusOneOptimized This refers to 1 + 1 bidirectional switching optimized for a network using predominantly 1 + 1 bidirectional switching as specified in ITU-T Recommendation G.783 (04/97) section B.1. Since this mode necessitates bidirectional switching, apsConfigDirection must be set to bidirectional whenever onePlusOneOptimized is set. This object may not be modified if the associated apsConfigRowStatus object is equal to active(1)." DEFVAL {onePlusOne} ::= { apsConfigEntry 3 }
Internet Assigned Numbers Authority
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.49.1.1.2.1.1 | apsConfigName | 0 | 0 | A textual name for the APS group. |
| 1.3.6.1.2.1.10.49.1.1.2.1.2 | apsConfigRowStatus | 0 | 0 | The status of this APS group entry. An entry may not exist in the active state unless all objects in the entry have an appropriat… |
| 1.3.6.1.2.1.10.49.1.1.2.1.4 | apsConfigRevert | 0 | 0 | The revertive mode of the APS group. nonrevertive Traffic remains on the protection line until another switch request is received.… |
| 1.3.6.1.2.1.10.49.1.1.2.1.5 | apsConfigDirection | 0 | 0 | The directional mode of the APS group. unidirectional The unidirectional mode provides protection in one direction. bidirectional T… |
| 1.3.6.1.2.1.10.49.1.1.2.1.6 | apsConfigExtraTraffic | 0 | 0 | This object enables or disables the transfer of extra traffic on the protection channel in a 1:n architecture. This object must b… |
| 1.3.6.1.2.1.10.49.1.1.2.1.7 | apsConfigSdBerThreshold | 0 | 0 | The Signal Degrade Bit Error Rate. The negated value of this number is used as the exponent of 10 for computing the threshold val… |
| 1.3.6.1.2.1.10.49.1.1.2.1.8 | apsConfigSfBerThreshold | 0 | 0 | The Signal Failure Bit Error Rate. The negated value of this number is used as the exponent of 10 for computing the threshold val… |
| 1.3.6.1.2.1.10.49.1.1.2.1.9 | apsConfigWaitToRestore | 0 | 0 | The Wait To Restore period in seconds. After clearing of a condition that necessitated an automatic switch, the wait to restore p… |
| 1.3.6.1.2.1.10.49.1.1.2.1.10 | apsConfigCreationTime | 0 | 0 | The value of sysUpTime at the time the row was created |
| 1.3.6.1.2.1.10.49.1.1.2.1.11 | apsConfigStorageType | 0 | 0 | The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columna… |