Configured allocation ratio of excess transmit
bandwidth between fast and interleaved channels. Only
applies when two channel mode and RADSL are supported.
Distribute bandwidth on each channel in excess of the
corresponding ChanConfMinTxRate so that:
adslAturConfRateChanRatio =
[Fast / (Fast + Interleaved)] * 100
In other words this value is the fast channel
percentage.
Parsed from file ADSL-LINE-MIB.mib
Module: ADSL-LINE-MIB
Configured allocation ratio of excess transmit
bandwidth between fast and interleaved channels. Only
applies when two channel mode and RADSL are supported.
Distribute bandwidth on each channel in excess of the
corresponding ChanConfMinTxRate so that:
adslAturConfRateChanRatio =
[Fast / (Fast + Interleaved)] * 100
In other words this value is the fast channel
percentage.
SYNTAX INTEGER(0..100)
UNITS "%"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Configured allocation ratio of excess transmit
bandwidth between fast and interleaved channels. Only
applies when two channel mode and RADSL are supported.
Distribute bandwidth on each channel in excess of the
corresponding ChanConfMinTxRate so that:
adslAturConfRateChanRatio =
[Fast / (Fast + Interleaved)] * 100
In other words this value is the fast channel
percentage."
View at oid-info.com
Configured allocation ratio of excess transmit
bandwidth between fast and interleaved channels. Only
applies when two channel mode and RADSL are supported.
Distribute bandwidth on each channel in excess of the
corresponding ChanConfMinTxRate so that:
adslAturConfRateChanRatio =
[Fast / (Fast + Interleaved)] * 100
In other words this value is the fast channel
percentage.
Parsed from file adsl-line.mib.txt
Company: None
Module: ADSL-LINE-MIB
Configured allocation ratio of excess transmit
bandwidth between fast and interleaved channels. Only
applies when two channel mode and RADSL are supported.
Distribute bandwidth on each channel in excess of the
corresponding ChanConfMinTxRate so that:
adslAturConfRateChanRatio =
[Fast / (Fast + Interleaved)] * 100
In other words this value is the fast channel
percentage.
adslAturConfRateChanRatio OBJECT-TYPE SYNTAX INTEGER(0..100) UNITS "%" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and RADSL are supported. Distribute bandwidth on each channel in excess of the corresponding ChanConfMinTxRate so that: adslAturConfRateChanRatio = [Fast / (Fast + Interleaved)] * 100 In other words this value is the fast channel percentage." ::= { adslLineConfProfileEntry 17 }
adslAturConfRateChanRatio OBJECT-TYPE SYNTAX INTEGER(0..100) ACCESS read-write STATUS mandatory DESCRIPTION "Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and RADSL are supported. Distribute bandwidth on each channel in excess of the corresponding ChanConfMinTxRate so that: adslAturConfRateChanRatio = [Fast / (Fast + Interleaved)] * 100 In other words this value is the fast channel percentage." ::= { adslLineConfProfileEntry 17 }
Defined in RFC2662
adslAturConfRateChanRatio OBJECT-TYPE SYNTAX INTEGER(0..100) UNITS "%" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and RADSL are supported. Distribute bandwidth on each channel in excess of the corresponding ChanConfMinTxRate so that: adslAturConfRateChanRatio = [Fast / (Fast + Interleaved)] * 100 In other words this value is the fast channel percentage." ::= { adslLineConfProfileEntry 17 }
adslAturConfRateChanRatio OBJECT-TYPE SYNTAX INTEGER(0..100) UNITS "%" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and RADSL are supported. Distribute bandwidth on each channel in excess of the corresponding ChanConfMinTxRate so that: adslAturConfRateChanRatio = [Fast / (Fast + Interleaved)] * 100 In other words this value is the fast channel percentage." ::= { adslLineConfProfileEntry 17 }
Internet Assigned Numbers Authority
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.2.1.10.94.1.1.14.1.1 | adslLineConfProfileName | 0 | 0 | This object is used by the line configuration table in order to identify a row of this table. When `dynamic' profiles are impleme… |
1.3.6.1.2.1.10.94.1.1.14.1.2 | adslAtucConfRateMode | 0 | 0 | Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information. |
1.3.6.1.2.1.10.94.1.1.14.1.3 | adslAtucConfRateChanRatio | 0 | 0 | Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mo… |
1.3.6.1.2.1.10.94.1.1.14.1.4 | adslAtucConfTargetSnrMgn | 0 | 0 | Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successful… |
1.3.6.1.2.1.10.94.1.1.14.1.5 | adslAtucConfMaxSnrMgn | 0 | 0 | Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power… |
1.3.6.1.2.1.10.94.1.1.14.1.6 | adslAtucConfMinSnrMgn | 0 | 0 | Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increa… |
1.3.6.1.2.1.10.94.1.1.14.1.7 | adslAtucConfDownshiftSnrMgn | 0 | 0 | Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrea… |
1.3.6.1.2.1.10.94.1.1.14.1.8 | adslAtucConfUpshiftSnrMgn | 0 | 0 | Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase… |
1.3.6.1.2.1.10.94.1.1.14.1.9 | adslAtucConfMinUpshiftTime | 0 | 0 | Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the … |
1.3.6.1.2.1.10.94.1.1.14.1.10 | adslAtucConfMinDownshiftTime | 0 | 0 | Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL is not present, t… |
1.3.6.1.2.1.10.94.1.1.14.1.11 | adslAtucChanConfFastMinTxRate | 0 | 0 | Configured Minimum Transmit rate for `Fast' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode… |
1.3.6.1.2.1.10.94.1.1.14.1.12 | adslAtucChanConfInterleaveMinTxRate | 0 | 0 | Configured Minimum Transmit rate for `Interleave' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADS… |
1.3.6.1.2.1.10.94.1.1.14.1.13 | adslAtucChanConfFastMaxTxRate | 0 | 0 | Configured Maximum Transmit rate for `Fast' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode… |
1.3.6.1.2.1.10.94.1.1.14.1.14 | adslAtucChanConfInterleaveMaxTxRate | 0 | 0 | Configured Maximum Transmit rate for `Interleave' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADS… |
1.3.6.1.2.1.10.94.1.1.14.1.15 | adslAtucChanConfMaxInterleaveDelay | 0 | 0 | Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the map… |
1.3.6.1.2.1.10.94.1.1.14.1.16 | adslAturConfRateMode | 0 | 0 | Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information. |
1.3.6.1.2.1.10.94.1.1.14.1.18 | adslAturConfTargetSnrMgn | 0 | 0 | Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successful… |
1.3.6.1.2.1.10.94.1.1.14.1.19 | adslAturConfMaxSnrMgn | 0 | 0 | Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power… |
1.3.6.1.2.1.10.94.1.1.14.1.20 | adslAturConfMinSnrMgn | 0 | 0 | Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increa… |
1.3.6.1.2.1.10.94.1.1.14.1.21 | adslAturConfDownshiftSnrMgn | 0 | 0 | Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrea… |
1.3.6.1.2.1.10.94.1.1.14.1.22 | adslAturConfUpshiftSnrMgn | 0 | 0 | Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase… |
1.3.6.1.2.1.10.94.1.1.14.1.23 | adslAturConfMinUpshiftTime | 0 | 0 | Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the … |
1.3.6.1.2.1.10.94.1.1.14.1.24 | adslAturConfMinDownshiftTime | 0 | 0 | Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL is not present, t… |
1.3.6.1.2.1.10.94.1.1.14.1.25 | adslAturChanConfFastMinTxRate | 0 | 0 | Configured Minimum Transmit rate for `Fast' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode… |
1.3.6.1.2.1.10.94.1.1.14.1.26 | adslAturChanConfInterleaveMinTxRate | 0 | 0 | Configured Minimum Transmit rate for `Interleave' channels, in bps. See adslAturConfRateChanRatio for information regarding RADS… |
1.3.6.1.2.1.10.94.1.1.14.1.27 | adslAturChanConfFastMaxTxRate | 0 | 0 | Configured Maximum Transmit rate for `Fast' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode… |
1.3.6.1.2.1.10.94.1.1.14.1.28 | adslAturChanConfInterleaveMaxTxRate | 0 | 0 | Configured Maximum Transmit rate for `Interleave' channels, in bps. See adslAturConfRateChanRatio for information regarding RADS… |
1.3.6.1.2.1.10.94.1.1.14.1.29 | adslAturChanConfMaxInterleaveDelay | 0 | 0 | Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the map… |
1.3.6.1.2.1.10.94.1.1.14.1.30 | adslLineConfProfileRowStatus | 0 | 0 | This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this ob… |