Configured maximum Interleave Delay for this channel.
Interleave delay applies only to the interleave channel
and defines the mapping (relative spacing) between
subsequent input bytes at the interleaver input and
their placement in the bit stream at the interleaver
output. Larger numbers provide greater separation
between consecutive input bytes in the output bit
stream allowing for improved impulse noise immunity
at the expense of payload latency.
Parsed from file ADSL-LINE-MIB.mib
Module: ADSL-LINE-MIB
Configured maximum Interleave Delay for this channel.
Interleave delay applies only to the interleave channel
and defines the mapping (relative spacing) between
subsequent input bytes at the interleaver input and
their placement in the bit stream at the interleaver
output. Larger numbers provide greater separation
between consecutive input bytes in the output bit
stream allowing for improved impulse noise immunity
at the expense of payload latency.
SYNTAX INTEGER(0..255)
UNITS "milli-seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Configured maximum Interleave Delay for this channel.
Interleave delay applies only to the interleave channel
and defines the mapping (relative spacing) between
subsequent input bytes at the interleaver input and
their placement in the bit stream at the interleaver
output. Larger numbers provide greater separation
between consecutive input bytes in the output bit
stream allowing for improved impulse noise immunity
at the expense of payload latency."
View at oid-info.com
Configured maximum Interleave Delay for this channel.
Interleave delay applies only to the interleave channel
and defines the mapping (relative spacing) between
subsequent input bytes at the interleaver input and
their placement in the bit stream at the interleaver
output. Larger numbers provide greater separation
between consecutive input bytes in the output bit
stream allowing for improved impulse noise immunity
at the expense of payload latency.
Parsed from file adsl-line.mib.txt
Company: None
Module: ADSL-LINE-MIB
Configured maximum Interleave Delay for this channel.
Interleave delay applies only to the interleave channel
and defines the mapping (relative spacing) between
subsequent input bytes at the interleaver input and
their placement in the bit stream at the interleaver
output. Larger numbers provide greater separation
between consecutive input bytes in the output bit
stream allowing for improved impulse noise immunity
at the expense of payload latency.
adslAturChanConfMaxInterleaveDelay OBJECT-TYPE SYNTAX INTEGER(0..255) UNITS "milli-seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency." ::= { adslLineConfProfileEntry 29 }
adslAturChanConfMaxInterleaveDelay OBJECT-TYPE SYNTAX INTEGER(0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency." ::= { adslLineConfProfileEntry 29 }
Defined in RFC2662
adslAturChanConfMaxInterleaveDelay OBJECT-TYPE SYNTAX INTEGER(0..255) UNITS "milli-seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency." ::= { adslLineConfProfileEntry 29 }
adslAturChanConfMaxInterleaveDelay OBJECT-TYPE SYNTAX INTEGER(0..255) UNITS "milli-seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency." ::= { adslLineConfProfileEntry 29 }
Internet Assigned Numbers Authority
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.94.1.1.14.1.1 | adslLineConfProfileName | 0 | 0 | This object is used by the line configuration table in order to identify a row of this table. When `dynamic' profiles are impleme… |
| 1.3.6.1.2.1.10.94.1.1.14.1.2 | adslAtucConfRateMode | 0 | 0 | Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information. |
| 1.3.6.1.2.1.10.94.1.1.14.1.3 | adslAtucConfRateChanRatio | 0 | 0 | Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mo… |
| 1.3.6.1.2.1.10.94.1.1.14.1.4 | adslAtucConfTargetSnrMgn | 0 | 0 | Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successful… |
| 1.3.6.1.2.1.10.94.1.1.14.1.5 | adslAtucConfMaxSnrMgn | 0 | 0 | Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power… |
| 1.3.6.1.2.1.10.94.1.1.14.1.6 | adslAtucConfMinSnrMgn | 0 | 0 | Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increa… |
| 1.3.6.1.2.1.10.94.1.1.14.1.7 | adslAtucConfDownshiftSnrMgn | 0 | 0 | Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrea… |
| 1.3.6.1.2.1.10.94.1.1.14.1.8 | adslAtucConfUpshiftSnrMgn | 0 | 0 | Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase… |
| 1.3.6.1.2.1.10.94.1.1.14.1.9 | adslAtucConfMinUpshiftTime | 0 | 0 | Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the … |
| 1.3.6.1.2.1.10.94.1.1.14.1.10 | adslAtucConfMinDownshiftTime | 0 | 0 | Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL is not present, t… |
| 1.3.6.1.2.1.10.94.1.1.14.1.11 | adslAtucChanConfFastMinTxRate | 0 | 0 | Configured Minimum Transmit rate for `Fast' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode… |
| 1.3.6.1.2.1.10.94.1.1.14.1.12 | adslAtucChanConfInterleaveMinTxRate | 0 | 0 | Configured Minimum Transmit rate for `Interleave' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADS… |
| 1.3.6.1.2.1.10.94.1.1.14.1.13 | adslAtucChanConfFastMaxTxRate | 0 | 0 | Configured Maximum Transmit rate for `Fast' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode… |
| 1.3.6.1.2.1.10.94.1.1.14.1.14 | adslAtucChanConfInterleaveMaxTxRate | 0 | 0 | Configured Maximum Transmit rate for `Interleave' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADS… |
| 1.3.6.1.2.1.10.94.1.1.14.1.15 | adslAtucChanConfMaxInterleaveDelay | 0 | 0 | Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the map… |
| 1.3.6.1.2.1.10.94.1.1.14.1.16 | adslAturConfRateMode | 0 | 0 | Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information. |
| 1.3.6.1.2.1.10.94.1.1.14.1.17 | adslAturConfRateChanRatio | 0 | 0 | Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mo… |
| 1.3.6.1.2.1.10.94.1.1.14.1.18 | adslAturConfTargetSnrMgn | 0 | 0 | Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successful… |
| 1.3.6.1.2.1.10.94.1.1.14.1.19 | adslAturConfMaxSnrMgn | 0 | 0 | Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power… |
| 1.3.6.1.2.1.10.94.1.1.14.1.20 | adslAturConfMinSnrMgn | 0 | 0 | Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increa… |
| 1.3.6.1.2.1.10.94.1.1.14.1.21 | adslAturConfDownshiftSnrMgn | 0 | 0 | Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrea… |
| 1.3.6.1.2.1.10.94.1.1.14.1.22 | adslAturConfUpshiftSnrMgn | 0 | 0 | Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase… |
| 1.3.6.1.2.1.10.94.1.1.14.1.23 | adslAturConfMinUpshiftTime | 0 | 0 | Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the … |
| 1.3.6.1.2.1.10.94.1.1.14.1.24 | adslAturConfMinDownshiftTime | 0 | 0 | Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL is not present, t… |
| 1.3.6.1.2.1.10.94.1.1.14.1.25 | adslAturChanConfFastMinTxRate | 0 | 0 | Configured Minimum Transmit rate for `Fast' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode… |
| 1.3.6.1.2.1.10.94.1.1.14.1.26 | adslAturChanConfInterleaveMinTxRate | 0 | 0 | Configured Minimum Transmit rate for `Interleave' channels, in bps. See adslAturConfRateChanRatio for information regarding RADS… |
| 1.3.6.1.2.1.10.94.1.1.14.1.27 | adslAturChanConfFastMaxTxRate | 0 | 0 | Configured Maximum Transmit rate for `Fast' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode… |
| 1.3.6.1.2.1.10.94.1.1.14.1.28 | adslAturChanConfInterleaveMaxTxRate | 0 | 0 | Configured Maximum Transmit rate for `Interleave' channels, in bps. See adslAturConfRateChanRatio for information regarding RADS… |
| 1.3.6.1.2.1.10.94.1.1.14.1.30 | adslLineConfProfileRowStatus | 0 | 0 | This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this ob… |