The baud rate to set the rs232 ports to at boot time.
Parsed from file h-sonet_mib.txt
Company: None
Module: NSCHippiSonet-MIB
The baud rate to set the rs232 ports to at boot time.
Parsed from file NSCHippiSonet-MIB.mib
Module: NSCHippiSonet-MIB
Vendor: NSC
Module: NSCHippiSonet-MIB
[Automatically extracted from oidview.com]
nscHippiSonetPortSpeed OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The baud rate to set the rs232 ports to at boot time." ::= { nscHippiSonetProfile 8 }
nscHippiSonetPortSpeed OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The baud rate to set the rs232 ports to at boot time." ::= { nscHippiSonetProfile 8 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.10.2.1.5.6.8.0 | nscHippiSonetPortSpeed | 0 | 0 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.10.2.1.5.6.1 | nscHippiSonetOpticalRcvOffset | 1 | 1 | String representation of the floating value for the offset of the optical receive light formula. |
| 1.3.6.1.4.1.10.2.1.5.6.2 | nscHippiSonetOpticalRcvSlope | 1 | 1 | String representation of the floating value for the slope of the optical receive light formula. |
| 1.3.6.1.4.1.10.2.1.5.6.3 | nscHippiSonetBiasCurrent | 1 | 1 | Integer representation of the floating value for the baseline current of the transmit laser in milliamps. This value is used by … |
| 1.3.6.1.4.1.10.2.1.5.6.4 | nscHippiSonetBiasTemp | 1 | 1 | Temperature in celcius at which the profiled bias current was taken. This value is used with the bias current to determine the l… |
| 1.3.6.1.4.1.10.2.1.5.6.5 | nscHippiSonetBackfaceVoltage | 1 | 1 | String representation of the floting value of the Voltage in millivolts that was measured at the backface of the laser when it wa… |
| 1.3.6.1.4.1.10.2.1.5.6.6 | nscHippiSonetIField | 1 | 1 | The I-Field address that is used by the hippi interface. |
| 1.3.6.1.4.1.10.2.1.5.6.7 | nscHippiSonetBootPort | 1 | 1 | Which rs232 port the boot information should be sent to. Ports 1 & 2 are the only valid ports with 1 being located on the back o… |
| 1.3.6.1.4.1.10.2.1.5.6.9 | nscHippiSonetThreshold | 1 | 1 | Threshold of the mega-fifo at which flow control will be activated. The value represents 8ths of the fifo with 7 representing th… |
| 1.3.6.1.4.1.10.2.1.5.6.10 | nscHippiTimeout | 1 | 1 | Timeout value to use when trying to connect from our hippi source. This timer is started when the source raises connect. If the… |
| 1.3.6.1.4.1.10.2.1.5.6.11 | nscHippiSonetDipSwitch | 1 | 1 | This is a software switch that functions much like a hardware dip switch. At the moment, the only use of this switch is to defin… |